Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TEST MODE PROCEDURE  


WARNING LIGHT INITIAL CHECK


a.

When the ignition switch is turned to ON, check that the ABS warning light and brake warning light illuminate and then turn off after 3 seconds. If a light remains on, proceed to troubleshooting for the light circuit below.

Trouble Area See procedure
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)
Brake warning light circuit (Remains on) (Click here)
Brake warning light circuit (Does not come on) (Click here)



SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (Using the GTS or Techstream)


HINT:

If the ignition switch is turned from ON to ACC or off during test mode (signal check), DTCs stored during the sensor check will be cleared.


a.

Procedure to enter test mode.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is centered.


iii.

Check that the shift lever is in neutral and apply the parking brake.


iv.

Connect the GTS or Techstream to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the GTS or Techstream on.


vii.

Switch the skid control ECU (brake actuator assembly) to test mode using the GTS or Techstream. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.


viii.

Check that the ABS warning light comes on for several seconds and then blinks in the test mode pattern (0.12 seconds on and 0.12 seconds off).

HINT:

If the ABS warning light does not blink, inspect the ECUT terminal circuit and ABS warning light circuit.


Trouble Area See procedure
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)




SPEED SENSOR CHECK (Using the GTS or Techstream)


NOTICE:
·

The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.

·

If the sensor check has not been completed, the ABS warning light will blink while driving and the ABS will not operate.



a.

Drive the vehicle straight-ahead.

Accelerate the vehicle to a speed of 20 km/h (13 mph) or more over several seconds.


b.

Check that the ABS warning light goes off.

HINT:
·

The sensor check may not be completed if wheelspin occurs.

·

The ABS warning light blinks when the sensor check is completed and the vehicle stops.

·

The ABS warning light comes on immediately if a malfunction is detected during the speed sensor check.




c.

Stop the vehicle.

HINT:

When the sensor check is completed, the ABS warning light goes off while driving and blinks in the test mode pattern (0.12 seconds on and 0.12 seconds off) while the vehicle is stationary.




END OF SENSOR CHECK (Using the GTS or Techstream)


a.

If the sensor check is completed, the ABS warning light blinks (0.12 seconds on and 0.12 seconds off) when the vehicle is stopped and turns off while the vehicle is being driven.

NOTICE:

If the signal check has not been completed, the ABS warning light blinks while driving and the ABS does not operate.




READ DTC OF SENSOR CHECK FUNCTION (Using the GTS or Techstream)


a.

Read the DTC(s) by following the GTS or Techstream screen.

NOTICE:
·

If only DTCs other than test mode sensor check DTCs are output, repair the malfunctions and clear the DTCs.

·

If test mode (signal check) DTCs and other DTCs are output or if only test mode (signal check) DTCs are output, repair the malfunctions, clear the DTCs, and perform the test mode (signal check) inspection again.



HINT:

Refer to the list of DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


ABS Sensor
DTC Code Detection Item Trouble Area
C1275/85 Abnormal change in output signal of front speed sensor RH Speed sensor rotor (Front axle with ABS sensor hub and bearing assembly RH)
C1276/86 Abnormal change in output signal of front speed sensor LH Speed sensor rotor (Front axle with ABS sensor hub and bearing assembly LH)
C1277/87 Abnormal change in output signal of rear speed sensor RH Speed sensor rotor (Rear axle hub and bearing assembly RH)
C1278/88 Abnormal change in output signal of rear speed sensor LH Speed sensor rotor (Rear axle hub and bearing assembly LH)



SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (Using SST Check Wire)


HINT:

If the ignition switch is turned from ON to ACC or off during test mode (signal check), DTCs stored during the sensor check will be cleared.


a.

Procedure to enter test mode.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is centered.


iii.

Check that the shift lever is in neutral and apply the parking brake.


iv.
C249767C08
1.604,0.771 1.417,0.354 true 1.844,1.427 1.844,1.792 true 1.344,0.167 1.583,0.448 0.24,0.281 10 E 1.719,1.833 2.26,2.115 0.542,0.281 10 ECUT 0.167,0.125 0.448,0.458 0.281,0.333 10 *a
*a Front view of DLC3


Using SST, connect terminals 13 (ECUT) and 4 (E) of the DLC3.

SST
09843-18040  


v.

Turn the ignition switch to ON.


vi.

Depressing the brake pedal 8 times or more within 5 seconds.


vii.

Check that the ABS warning light comes on for several seconds and then blinks in the test mode pattern (0.12 seconds on and 0.12 seconds off).

HINT:

If the ABS warning light does not blink, inspect the ABS warning light circuit.


Trouble Area See procedure
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)




SPEED SENSOR CHECK (Using SST Check Wire)


NOTICE:
·

The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.

·

If the sensor check has not been completed, the ABS warning light will blink while driving and the ABS will not operate.



a.

Drive the vehicle straight-ahead.

Accelerate the vehicle to a speed of 20 km/h (13 mph) or more over several seconds.


b.

Check that the ABS warning light goes off.

HINT:
·

The sensor check may not be completed if wheelspin occurs.

·

The ABS warning light blinks when the sensor check is completed and the vehicle stops.

·

The ABS warning light comes on immediately if a malfunction is detected during the speed sensor check.




c.

Stop the vehicle.

HINT:

When the sensor check is completed, the ABS warning light goes off while driving and blinks in the test mode pattern (0.12 seconds on and 0.12 seconds off) while the vehicle is stationary.




END OF SENSOR CHECK (Using SST Check Wire)


a.

If the sensor check is completed, the ABS warning light blinks (0.12 seconds on and 0.12 seconds off) when the vehicle is stopped and turns off while the vehicle is being driven.

NOTICE:

If the sensor check has not been completed, the ABS warning light blinks while driving and the ABS does not operate.




READ DTC OF SENSOR CHECK FUNCTION (Using SST Check Wire)


a.
C249767C08
1.604,0.771 1.417,0.354 true 1.844,1.427 1.844,1.792 true 1.344,0.167 1.583,0.448 0.24,0.281 10 E 1.719,1.833 2.26,2.115 0.542,0.281 10 ECUT 0.167,0.125 0.448,0.458 0.281,0.333 10 *a
*a Front view of DLC3


Using SST, connect terminals 13 (ECUT) and 4 (E) of the DLC3.

SST
09843-18040  


b.

Count the number of blinks of the ABS warning light.

NOTICE:
·

If only DTCs other than test mode sensor check DTCs are output, repair the malfunctions and clear the DTCs.

·

If test mode (signal check) DTCs and other DTCs are output or if only test mode (signal check) DTCs are output, repair the malfunctions, clear the DTCs, and perform the test mode (signal check) inspection again.



HINT:
·

If more than 1 malfunction is detected at the same time, the lowest numbered code is output first.




c.

After performing the check, disconnect SST from terminals 4 (E) and 13 (ECUT) of the DLC3, and then turn the ignition switch off.


d.

Turn the ignition switch to ON.

HINT:

If the ignition switch is not turned to ON after SST is removed from the DLC3, the previous test mode continues.




DTC OF SENSOR CHECK FUNCTION


HINT:

The codes in this table are output only in test mode (signal check).


ABS Sensor
DTC Code Detection Item Trouble Area
C1275/85 Abnormal change in output signal of front speed sensor RH Speed sensor rotor (Front axle with ABS sensor hub and bearing assembly RH)
C1276/86 Abnormal change in output signal of front speed sensor LH Speed sensor rotor (Front axle with ABS sensor hub and bearing assembly LH)
C1277/87 Abnormal change in output signal of rear speed sensor RH Speed sensor rotor (Rear axle hub and bearing assembly RH)
C1278/88 Abnormal change in output signal of rear speed sensor LH Speed sensor rotor (Rear axle hub and bearing assembly LH)