Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.


WIRING DIAGRAM

C332708E02
0.156,6.448 1.156,7.01 1,0.563 10 false Main Body ECU (Fuse Block Assembly) 0.792,7.531 2.677,7.75 1.885,0.219 10 false : CAN Communication Line 1.875,6.385 4.26,6.917 2.385,0.531 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Sub-Assembly) 2.688,2.792 4.583,3.063 1.896,0.271 10 false Combination Meter Assembly 2.698,2.594 3,2.792 0.302,0.198 10 false E34 5.469,5.354 7.052,5.74 1.583,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 0.531,0.448 1.01,0.635 0.479,0.188 10 false CANH 0.552,0.917 1.031,1.104 0.479,0.188 10 false CANL 1.094,0.438 1.396,0.635 0.302,0.198 10 false 3C 1.083,0.885 1.385,1.083 0.302,0.198 10 false 3C 1.083,5.969 1.385,6.167 0.302,0.198 10 false 3D 0.396,4.417 0.896,4.604 0.5,0.188 10 false BKSW 1.146,5.729 1.375,5.938 0.229,0.208 10 false 3 1.094,0.688 1.396,0.885 0.302,0.198 10 false 30 1.115,0.219 1.417,0.417 0.302,0.198 10 false 21 2.74,1.365 3.219,1.552 0.479,0.188 10 false CANH 2.74,1.813 3.219,2 0.479,0.188 10 false CANL 2.552,1.167 2.854,1.365 0.302,0.198 10 false 9 2.542,1.625 2.844,1.823 0.302,0.198 10 false 8 6.208,0.427 6.688,0.615 0.479,0.188 10 false CANH 6.219,0.896 6.698,1.083 0.479,0.188 10 false CANL 5.938,0.24 6.24,0.438 0.302,0.198 10 false 22 5.917,0.708 6.219,0.906 0.302,0.198 10 false 10 5.479,5.156 5.865,5.375 0.385,0.219 10 false A13 6.208,4.271 6.688,4.458 0.479,0.188 10 false GND1 6.208,4.76 6.688,4.948 0.479,0.188 10 false GND2 5.948,4.135 6.25,4.333 0.302,0.198 10 false 25 5.979,4.615 6.208,4.813 0.229,0.198 10 false 1 6.219,3.302 6.698,3.49 0.479,0.188 10 false +BS 6.229,3.792 6.708,3.979 0.479,0.188 10 false +IG 4.135,3.479 4.615,3.667 0.479,0.188 10 false ABS2 4.073,3.99 4.677,4.167 0.604,0.177 10 false ECU-IG1 5.938,3.177 6.24,3.375 0.302,0.198 10 false 38 5.969,3.688 6.271,3.885 0.302,0.198 10 false 12 1.885,6.198 2.188,6.396 0.302,0.198 10 false A7 2.469,5.854 2.698,6.063 0.229,0.208 10 false 1 3.552,5.833 3.781,6.042 0.229,0.208 10 false 2 2.698,5.979 2.927,6.188 0.229,0.208 10 false + 3.365,5.969 3.594,6.177 0.229,0.208 10 false - 1.083,1.823 1.385,2.021 0.302,0.198 10 false 3G 1.083,1.365 1.385,1.563 0.302,0.198 10 false 3G 1.104,1.156 1.406,1.354 0.302,0.198 10 false 17 1.104,1.615 1.406,1.813 0.302,0.198 10 false 16 0.542,1.365 1.021,1.552 0.479,0.188 10 false CANH 0.552,1.833 1.031,2.021 0.479,0.188 10 false CANL 2.344,3.313 3.219,3.49 0.875,0.177 10 false from Battery 2.219,3.802 3.313,4.031 1.094,0.229 10 false from IG1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

If the brake actuator is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B




A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C330019C27
1.51,0.25 1.927,0.5 0.417,0.25 2.25,0.99 2.479,0.469 true 2.51,1.375 2.625,1.802 true 0.927,1.365 0.865,1.854 true 0.115,0.094 0.427,0.344 0.313,0.25 10 false *a 1.594,0.292 1.99,0.583 0.396,0.292 10 false A13 0.667,1.896 1.146,2.125 0.479,0.229 10 false GND1 2.438,0.281 2.729,0.521 0.292,0.24 10 false +IG 2.531,1.844 2.823,2.083 0.292,0.24 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A13 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-38 (+BS) - Body ground Always 11 to 14 V
A13-38 (+BS) - A13-25 (GND1) Always 11 to 14 V
A13-12 (+IG) - Body ground Ignition switch ON 11 to 14 V
A13-12 (+IG) - A13-25 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)

5.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
C330019C28
1.51,0.25 1.927,0.5 0.417,0.25 1.323,1.875 1.135,1.875 1.135,1.875 0.958,1.354 true 0.875,0.99 0.646,0.448 0.646,0.448 0.479,0.448 true 0.115,0.094 0.427,0.344 0.313,0.25 10 false *a 1.583,0.292 1.979,0.583 0.396,0.292 10 false A13 1.396,1.823 1.906,2.125 0.51,0.302 10 false GND1 0.073,0.365 0.583,0.667 0.51,0.302 10 false GND2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-25 (GND1) - Body ground Always Below 1 Ω
A13-1 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS OR TECHSTREAM (BRAKE FLUID SW)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)

6.READ VALUE USING GTS OR TECHSTREAM (BRAKE FLUID SW)
a.

Reconnect the A13 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS or Techstream to the DLC3.


c.

Connect the A7 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


d.

Turn the ignition switch to ON.


e.

Select the Data List using the GTS or Techstream.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Fluid SW Brake level warning switch ON or OFF ON: Brake fluid switch on
OFF: Brake fluid switch off
-


f.

Disconnect the F62 connector of the brake master cylinder reservoir sub-assembly again, and then reconnect it to check the tester display.

OK:

The tester display changes in response to the connector status of connection or disconnection.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS OR TECHSTREAM (BRAKE WARNING LAMP)

NG

8.INSPECT BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
7.READ VALUE USING GTS OR TECHSTREAM (BRAKE WARNING LAMP)
a.

Reconnect the A7 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


b.

Reconnect the E34 combination meter assembly connector.


c.

Select the Data List on the GTS or Techstream.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake warning lamp Brake warning light ON or OFF ON: Warning light on
OFF: Warning light off
-


d.

Check the GTS or Techstream display condition of the brake warning light.

Result:
Result Proceed to
Display of the Data List remains ON. A
Display of the Data List remains OFF. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

8.INSPECT BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
a.
C230719C14
1.958,1.948 2.458,2.771 false 1.521,1.948 1.021,2.771 false 2.427,2.792 2.583,2.979 0.156,0.188 10 false + 0.958,2.781 1.115,2.969 0.156,0.188 10 false - 0.198,0.198 0.51,0.354 0.313,0.156 10 false *a
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))


Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the A7 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the brake fluid level.


Standard Resistance:
Tester Connection Condition Specified Condition
1 (+) - 2 (-) Switch OFF (Float up) 1.9 to 2.1 kΩ
1 (+) - 2 (-) Switch ON (Float down) Below 1 Ω


HINT:

If the switch condition is normal, adjust the brake fluid level to the MAX level.



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Disconnect the 3D main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-3 - A7-1 (+) Always Below 1 Ω
3D-3 or A7-1 (+) - Body ground Always 10 kΩ or higher
A7-2 (-) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR