Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

When one of the following conditions is met, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter and the skid control ECU (brake actuator assembly).

·

The anti-lock brake system is defective.


WIRING DIAGRAM

C333200E02
5.167,4.865 6.813,5.333 1.646,0.469 10 false Skid Control ECU (Brake Actuator Assembly) 5.156,4.677 5.615,4.875 0.458,0.198 10 false A13 5.49,0.833 5.948,1.031 0.458,0.198 10 false CANH 5.49,1.396 5.948,1.594 0.458,0.198 10 false CANL 5.208,0.646 5.667,0.844 0.458,0.198 10 false 22 5.208,1.208 5.667,1.406 0.458,0.198 10 false 10 4.438,0.688 4.896,0.885 0.458,0.198 10 false 39 4.448,1.219 4.906,1.417 0.458,0.198 10 false 40 2.979,0.656 3.438,0.854 0.458,0.198 10 false 25 2.979,1.208 3.438,1.406 0.458,0.198 10 false 26 3.948,0.833 4.406,1.031 0.458,0.198 10 false CANH 3.958,1.396 4.417,1.594 0.458,0.198 10 false CANL 3.271,0.833 3.729,1.031 0.458,0.198 10 false HCAN 3.26,1.385 3.719,1.583 0.458,0.198 10 false LCAN 1.823,0.708 2.281,0.906 0.458,0.198 10 false CANH 1.823,1.26 2.281,1.458 0.458,0.198 10 false CANL 2.323,0.635 2.5,0.833 0.177,0.198 10 false 9 2.313,1.167 2.49,1.365 0.177,0.198 10 false 8 0.708,1.125 1.271,1.313 0.563,0.188 10 false CAN IC 0.76,2.104 1.125,2.302 0.365,0.198 10 false CPU 0.979,2.906 1.344,3.104 0.365,0.198 10 false ABS 2.802,2.854 3.469,3.042 0.667,0.188 10 false ECU IG2 2.042,2.563 2.271,2.74 0.229,0.177 10 false IG 5.479,3.625 5.792,3.844 0.313,0.219 10 false +IG 5.49,4.333 5.802,4.552 0.313,0.219 10 false +BS 5.188,3.49 5.5,3.708 0.313,0.219 10 false 12 5.198,4.188 5.51,4.406 0.313,0.219 10 false 38 4.438,3.802 5.104,3.99 0.667,0.188 10 false ECU-IG1 4.469,4.5 5.135,4.688 0.667,0.188 10 false ABS2 6.01,3.302 6.677,3.49 0.667,0.188 10 false GND1 6,3.844 6.667,4.031 0.667,0.188 10 false GND2 2.344,2.552 2.521,2.75 0.177,0.198 10 false 5 6.49,3.146 6.948,3.344 0.458,0.198 10 false 25 6.49,3.708 6.948,3.906 0.458,0.198 10 false 1 0.365,3.573 2.281,3.813 1.917,0.24 10 false Combination Meter Assembly 0.385,3.365 0.844,3.563 0.458,0.198 10 false E34 0.844,5.333 2.76,5.573 1.917,0.24 10 false : CAN Communication Line 3.344,1.948 3.802,2.146 0.458,0.198 10 false A24 3.74,1.948 4.198,2.146 0.458,0.198 10 false ECM 3.042,4.323 3.865,4.542 0.823,0.219 10 false from Battery 2.896,3.625 3.885,3.854 0.99,0.229 10 false from IG1 Relay 4.073,2.688 5.063,2.917 0.99,0.229 10 false from IG2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Result Proceed to
DTC not output A
DTC output B




A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.


Result:
Proceed to
OK
NG




OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (POWER SOURCE TERMINAL)

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

4.CHECK TERMINAL VOLTAGE (POWER SOURCE TERMINAL)
a.
C330019C26
1.5,0.167 1.917,0.417 0.417,0.25 2.594,0.448 2.271,0.99 true 2.906,1.802 2.563,1.354 true 0.719,1.865 0.906,1.365 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 1.573,0.208 2.031,0.406 0.458,0.198 10 false A13 2.635,0.344 3.094,0.542 0.458,0.198 10 false +IG 2.823,1.844 3.281,2.042 0.458,0.198 10 false +BS 0.531,1.917 0.99,2.115 0.458,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-38 (+BS) - Body ground Always 11 to 14 V
A13-38 (+BS) - A13-25 (GND1) Always 11 to 14 V
A13-12 (+IG) - Body ground Ignition switch ON 11 to 14 V
A13-12 (+IG) - A13-25 (GND1) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-25 (GND1) - Body ground Always Below 1 Ω
A13-1 (GND2) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

6.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (ABS WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS or Techstream to the DLC3.


c.

Start the engine.


d.

Perform the Active Test of the skid control ECU (brake actuator assembly) using the GTS or Techstream.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Test Part Control Range Diagnostic Note
ABS warning lamp ABS warning light ON/OFF Observe the combination meter assembly

Result:
Result Proceed to
Does not change between ON and OFF A
Changes between ON and OFF B




A

B