Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C0226/52  SFR Solenoid Circuit  C0236/54  SFL Solenoid Circuit  C0246/56  SRR Solenoid Circuit  C0256/58  SRL Solenoid Circuit  


DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C0226/52 SFR Solenoid Circuit
1.

When the solenoid drive is abnormal.

2.

When the solenoid resistance value is abnormal.

3.

When the ECU drive request and feedback signal do not match.


·

ABS2 fuse

·

Solenoid circuit

·

Skid control ECU (Brake actuator assembly)


-
C0236/54 SFL Solenoid Circuit
1.

When the solenoid drive is abnormal.

2.

When the solenoid resistance value is abnormal.

3.

When the ECU drive request and feedback signal do not match.


·

ABS2 fuse

·

Solenoid circuit

·

Skid control ECU (Brake actuator assembly)


-
C0246/56 SRR Solenoid Circuit
1.

When the solenoid drive is abnormal.

2.

When the solenoid resistance value is abnormal.

3.

When the ECU drive request and feedback signal do not match.


·

ABS2 fuse

·

Solenoid circuit

·

Skid control ECU (Brake actuator assembly)


-
C0256/58 SRL Solenoid Circuit
1.

When the solenoid drive is abnormal.

2.

When the solenoid resistance value is abnormal.

3.

When the ECU drive request and feedback signal do not match.


·

ABS2 fuse

·

Solenoid circuit

·

Skid control ECU (Brake actuator assembly)


-

WIRING DIAGRAM

C274051E02
0.094,1.26 1.927,1.458 1.833,0.198 10 false from Battery 1.677,1.448 2.198,1.656 0.521,0.208 10 false ABS2 4.073,1.177 6.823,1.375 2.75,0.198 10 false ABS Solenoid Relay 2.531,3.042 2.844,3.24 0.313,0.198 10 false 25 2.531,1.167 2.844,1.365 0.313,0.198 10 false 38 2.594,3.906 2.823,4.104 0.229,0.198 10 false 1 2.802,1.167 3.26,1.365 0.458,0.198 10 false +BS 2.844,3.115 3.458,3.313 0.615,0.198 10 false GND1 2.833,3.969 3.448,4.167 0.615,0.198 10 false GND2 4.104,5.333 6.552,5.531 2.448,0.198 10 false Skid Control ECU 3.76,6 4.219,6.198 0.458,0.198 10 false A13 3.74,6.167 5.521,6.5 1.781,0.333 10 false Brake Actuator Assembly 5.927,1.031 6.542,1.229 0.615,0.198 10 false SRLR 5.927,1.542 6.542,1.74 0.615,0.198 10 false SRLH 5.927,2.063 6.542,2.26 0.615,0.198 10 false SFRR 5.927,2.573 6.542,2.771 0.615,0.198 10 false SFRH 5.927,3.063 6.542,3.26 0.615,0.198 10 false SFLR 5.927,3.573 6.542,3.771 0.615,0.198 10 false SFLH 5.927,4.063 6.542,4.26 0.615,0.198 10 false SRRR 5.927,4.583 6.542,4.781 0.615,0.198 10 false SRRH

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the brake actuator is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

The solenoid circuits are in the skid control ECU (brake actuator assembly). Therefore, the solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the brake actuator assembly.



b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC not output A
DTC output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

It is suspected that the DTCs were output due to a bad connection of the connector terminal.





A

B