Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C0273/13  Open in ABS Motor Relay Circuit  C0273/14  Short in ABS Motor Relay Circuit  


DESCRIPTION

The ABS motor relay supplies power to the ABS pump motor. While the ABS is activated, the skid control ECU (brake actuator assembly) turns the ABS motor relay on and operates the ABS pump motor.

The ABS motor relay is housed in the skid control ECU in the brake actuator assembly.

If the voltage supplied to the motor relay (+BM) is below the DTC detection threshold due to low voltage from the battery or generator, the DTC may be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C0273/13 Open in ABS Motor Relay Circuit
1.

Relay contact is open when the relay is on.

2.

Relay contact remains open when the relay is on.


·

ABS fuse

·

ABS motor relay circuit

·

Skid control ECU (Brake actuator assembly)


-
C0273/14 Short in ABS Motor Relay Circuit When the motor relay is off, the motor relay remains closed.
·

ABS motor relay circuit

·

Skid control ECU (Brake actuator assembly)


-

WIRING DIAGRAM

C274042E02
0.417,1.115 2.25,1.313 1.833,0.198 10 false from Battery 2.219,1.302 2.677,1.531 0.458,0.229 10 false ABS 3.5,1 3.958,1.198 0.458,0.198 10 false +BM 3.5,1.875 4.115,2.073 0.615,0.198 10 false GND1 3.5,2.292 4.115,2.49 0.615,0.198 10 false GND2 3.198,1 3.406,1.188 0.208,0.188 10 false 13 3.198,1.74 3.51,1.938 0.313,0.198 10 false 25 3.229,2.292 3.438,2.531 0.208,0.24 10 false 1 4.958,1.083 6.344,1.344 1.385,0.26 10 false ABS Motor Relay 4.99,1.5 6.365,1.792 1.375,0.292 10 false Skid Control ECU 4.792,3.552 6.938,3.75 2.146,0.198 10 false ABS Pump Motor 4.25,4 4.708,4.198 0.458,0.198 10 false A13 4.25,4.167 6.031,4.49 1.781,0.323 10 false Brake Actuator Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the skid control (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK TERMINAL VOLTAGE (+BM TERMINAL)
C330019C22
1.5,0.167 1.917,0.417 0.417,0.25 2.469,0.51 2.469,0.979 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 1.604,0.208 2.063,0.406 0.458,0.198 10 false A13 2.302,0.302 2.76,0.5 0.458,0.198 10 false +BM
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-13 (+BM) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-25 (GND1) - Body ground Always Below 1 Ω
A13-1 (GND2) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC
HINT:

These codes are detected when a problem is identified in the skid control ECU (brake actuator assembly).

The ABS motor relay is in the skid control ECU (brake actuator assembly). Therefore, the ABS motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the brake actuator assembly.



b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC not output A
DTC output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

It is suspected that the DTCs were output due to a bad connection of the connector terminal.





A

B