Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TEST MODE PROCEDURE  


SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (USING THE GTS OR TECHSTREAM)


NOTICE:

The test mode inspection is conducted after the power steering ECU has been replaced with a new one.


HINT:
·

Speed sensor signals can be checked easily in test mode.

·

Test mode codes C1571 and C1573 are stored during transition to test mode. These codes do not indicate a malfunction since the codes will be cleared when the ECU determines that the sensor is normal.

·

The test mode codes are cleared simultaneously when test mode is terminated.



a.

Enter Test Mode

i.

Turn the ignition switch off.


ii.

Connect the GTS or Techstream to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS or Techstream on.


v.

Switch the power steering ECU to the Test Mode. Enter the following menus: Chassis / EPS / Utility / Test Mode.



b.

Check that the EPS warning light comes on for several seconds and then blinks in the test mode pattern (0.25 seconds on and 0.25 seconds off).


c.

Check vehicle speed signal and engine speed signal.

i.

Drive the vehicle and accelerate until the vehicle speed reaches 20 km/h (12 mph) or more.

HINT:

If the engine speed exceeds 450 rpm during this check, engine speed signals will also be checked simultaneously.


C229852E03
0.271,0.156 2.083,0.417 1.813,0.26 10 When system is normal: 1.927,0.542 2.865,0.75 0.938,0.208 10 km/h (mph) 0.552,1.344 1.635,1.521 1.083,0.177 10 Vehicle speed 2.021,1.094 2.51,1.281 0.49,0.188 10 20 (12) 3.427,1.302 4.104,1.448 0.677,0.146 10 2 seconds 2.271,1.667 2.573,1.833 0.302,0.167 10 0 0.5,2.438 1.698,2.781 1.198,0.344 10 EPS warning light 1.802,2.313 2.177,2.469 0.375,0.156 10 ON 1.802,2.594 2.219,2.76 0.417,0.167 10 OFF 2.323,2.792 3.115,3.01 0.792,0.219 10 4 Hz blink 3.229,2.792 7.094,3.125 3.865,0.333 10 Light blinks until test mode code C1571 and C1573 is cleared. 6.052,1.656 6.646,1.844 0.594,0.188 10 Time 3.229,3.094 6.917,3.542 3.688,0.448 10 Light goes off when driving at 20 km/h (12 mph) or more for 2 seconds or more.



d.

Check the DTCs in test mode.

Test Mode Code
Code Detection Item Condition to Clear Code Trouble Area
C1571
((Click here))
Vehicle speed signal Vehicle speed at 20 km/h (12 mph) or more for 2 seconds or more If the code cannot be cleared, any of the following areas may be malfunctioning:
·

Speed sensor circuit

·

Brake control system (w/ABS)

·

CAN communication system


C1573
((Click here))
Engine speed signal Engine speed at 450 rpm or more for 2 seconds or more If the code cannot be cleared, any of the following areas may be malfunctioning:
·

Engine speed signal circuit

·

Power steering ECU assembly

·

ECM





SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (USING SST CHECK WIRE)


NOTICE:

The test mode inspection is conducted after the power steering ECU has been replaced with a new one.


HINT:
·

Speed sensor signals can be checked easily in test mode.

·

Test mode codes C1571 and C1573 are stored during transition to test mode. These codes do not indicate a malfunction since the codes will be cleared when the ECU determines that the sensor is normal.

·

The test mode codes are cleared simultaneously when test mode is terminated.



a.
C193959C13
2,1.854 1.844,1.854 1.844,1.854 1.75,1.448 true 2.094,0.396 1.896,0.396 1.896,0.396 1.583,0.906 true 0.073,0.052 0.24,0.219 0.167,0.167 10 false *a 2.073,1.781 2.479,1.958 0.406,0.177 10 false ECUT 2.146,0.323 2.302,0.5 0.156,0.177 10 false E
*a Front view of DLC3


Enter Test Mode

i.

Turn the ignition switch off.


ii.

Using SST Connect terminals 13 (ECUT) and 4 (E) of the DLC3.

SST
09843-18040  


iii.

Turn the ignition switch to ON.

HINT:

Be sure to connect the correct terminals of the connector, otherwise a malfunction may occur.



iv.

Connect the SST check wire to terminal 4 (E) and disconnect it, and repeat this procedure 2 times at intervals of 2 seconds.



b.

Check that the EPS warning light comes on for several seconds and then blinks in the test mode pattern (0.25 seconds on and 0.25 seconds off).


c.

Check vehicle speed signal and engine speed signal.

i.

Drive the vehicle and accelerate until the vehicle speed reaches 20 km/h (12 mph) or more.

HINT:

If the engine speed exceeds 450 rpm during this check, engine speed signals will also be checked simultaneously.


C229852E03
0.271,0.156 2.083,0.417 1.813,0.26 10 When system is normal: 1.927,0.542 2.865,0.75 0.938,0.208 10 km/h (mph) 0.552,1.344 1.635,1.521 1.083,0.177 10 Vehicle speed 2.021,1.094 2.51,1.281 0.49,0.188 10 20 (12) 3.427,1.302 4.104,1.448 0.677,0.146 10 2 seconds 2.271,1.667 2.573,1.833 0.302,0.167 10 0 0.5,2.438 1.698,2.781 1.198,0.344 10 EPS warning light 1.802,2.313 2.177,2.469 0.375,0.156 10 ON 1.802,2.594 2.219,2.76 0.417,0.167 10 OFF 2.323,2.792 3.115,3.01 0.792,0.219 10 4 Hz blink 3.229,2.792 7.094,3.125 3.865,0.333 10 Light blinks until test mode code C1571 and C1573 is cleared. 6.052,1.656 6.646,1.844 0.594,0.188 10 Time 3.229,3.094 6.917,3.542 3.688,0.448 10 Light goes off when driving at 20 km/h (12 mph) or more for 2 seconds or more.



d.

Check the DTCs in test mode.

Test Mode Code
Code Detection Item Condition to Clear Code Trouble Area
71
((Click here))
Vehicle speed signal Vehicle speed at 20 km/h (12 mph) or more for 2 seconds or more If the code cannot be cleared, any of the following areas may be malfunctioning:
·

Speed sensor circuit

·

Brake control system (w/ABS)

·

CAN communication system


73
((Click here))
Engine speed signal Engine speed at 450 rpm or more for 2 seconds or more If the code cannot be cleared, any of the following areas may be malfunctioning:
·

Engine speed signal circuit

·

Power steering ECU assembly

·

ECM