Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1552/52  PIG Voltage Abnormality  C1553/53  Overvoltage  C1554/54  Power Supply Relay Failure  


DESCRIPTION

When a problem occurs in the system, the power source relay circuit and the motor relay circuit are shut off to stop the power assist. The ECU must be replaced when there is a problem with the relays because each relay is built into the ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1552/52 PIG Voltage Abnormality PIG power source circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU Assembly


Comes on (Red) Ignition switch ON again or after system confirmed to be normal Buzzer :
Sounds in termittently
C1553/53 Overvoltage Abnormal over voltage
·

IG and PIG power source circuits

·

Power steering ECU Assembly


Comes on (Red) Ignition switch ON again or after system confirmed to be normal Buzzer :
Sounds in termittently
C1554/54 Power Supply Relay Failure Power source relay circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU Assembly


Comes on (Red) Ignition switch ON again Buzzer :
Sounds in termittently

WIRING DIAGRAM

Refer to DTCs C1523/23, C1524/24 and C1555/55.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>C1523/23

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS OR TECHSTREAM (PIG POWER SUPPLY)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Chassis / EPS / Data List.


e.

Select the item "PIG Power Supply" in the Data List and read the value displayed on the GTS or Techstream.

Chassis > EPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PIG power supply Power source voltage to activate motor Min: 0 V
Max: 21.1531 V
11 to 14 V Power steering is in operation
Chassis > EPS > Data List
Tester Display
PIG power supply
50003 581 7
OK:

The normal condition value is displayed on the GTS or Techstream.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE POWER STEERING ECU

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the E74 power steering ECU assembly connector.


b.
C332781C07
2.24,0.406 2.625,0.604 0.385,0.198 2.792,1.708 2.552,1.021 true 2.135,1.74 2.313,1.021 true 2.313,0.427 2.625,0.625 0.313,0.198 10 false E74 1.844,1.781 2.427,2 0.583,0.219 10 false 2 (GND) 2.51,1.771 3.104,2 0.594,0.229 10 false 1 (BAT+) 0.156,0.094 0.469,0.292 0.313,0.198 10 false *a
*a Component with harness connected
(Power Steering ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E74-1 (BAT+) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E74-2 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.INSPECT STEERING COLUMN ASSEMBLY (POWER STEERING MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING COLUMN ASSEMBLY (POWER STEERING MOTOR)
a.

Disconnect the z1 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-1 (M1) - z1-2 (M2) Always Below 1 Ω
z1-1 (M1) - Body ground Always 1 MΩ or higher
z1-2 (M2) - Body ground Always 1 MΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE STEERING COLUMN ASSEMBLY