Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003005 DOOR LOCK _0015187 WIRELESS DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  Only Wireless Control Function is Inoperative  


DESCRIPTION

The main body ECU (fuse block assembly) receives signals from the door control transmitter. Then, the main body ECU (fuse block assembly) sends lock/unlock signals to all door lock motors.

PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Each door locks and unlocks normally.


Result:
Proceed to
OK
NG




OK

2.CHECK KEY REMINDER WARNING SYSTEM

NG

2.CHECK KEY REMINDER WARNING SYSTEM
a.

Check that the key reminder warning buzzer operates normally.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK

OK:

Key reminder warning buzzer operates normally.


Result:
Proceed to
OK
NG




OK

3.CHECK DOOR CONTROL TRANSMITTER

NG

3.CHECK DOOR CONTROL TRANSMITTER
a.

Check whether the wireless door lock control functions operate normally with another registered transmitter.

OK:

Wireless door lock control functions operate normally.


Result:
Proceed to
OK
NG




OK

4.INSPECT TRANSMITTER BATTERY

NG

5.CHECK WAVE ENVIRONMENT
4.INSPECT TRANSMITTER BATTERY
B419117C01
1.406,2 1.573,1.667 1.573,1.667 1.656,1.667 false 0.625,0.406 0.729,0.229 0.729,0.229 0.813,0.229 false 0.167,0.135 0.563,0.417 0.396,0.281 10 false *A 0.167,1.896 0.563,2.177 0.396,0.281 10 false *B 1.698,1.573 2.094,1.854 0.396,0.281 10 false *1 0.896,0.146 1.292,0.427 0.396,0.281 10 false *1
*A for Key Type
*B for Key Ring Type
*1 Wire


a.

Remove the battery from the door control transmitter that does not operate.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(for Key Ring Type)>REPLACEMENT


b.

Attach a lead wire (0.6 mm (0.0236 in.) or less in diameter including wire sheath) with tape or equivalent to the negative terminal.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between the terminals or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.



c.

Carefully extend the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

NOTICE:

When replacing the transmitter battery, before starting work, remove any static electricity that has built up by touching, for example, the vehicle to prevent the door control transmitter from being damaged.



d.
B419118C01
1.521,1.917 1.771,1.667 1.771,1.667 1.854,1.667 false 0.698,0.417 0.875,0.229 0.875,0.229 0.958,0.229 false 0.115,0.104 0.667,0.552 0.552,0.448 10 false *A 0.104,1.885 0.656,2.333 0.552,0.448 10 false *B 1.021,0.156 1.573,0.604 0.552,0.448 10 false *a 1.917,1.583 2.469,2.031 0.552,0.448 10 false *a
*A for Key Type
*B for Key Ring Type
*a GND


Measure the voltage according to the value(s) in the table below.

HINT:
·

Measure the transmitter battery voltage while pressing the lock or unlock switch on the transmitter.

·

Perform the measurement when the door control transmitter is at room temperature.



Standard Voltage:
Tester Connection Condition Specified Condition
Battery positive (+) - Battery negative (-) Ignition switch off, all doors closed and lock or unlock switch pushed 2.5 to 3.2 V


Result:
Result Proceed to
OK (for Key Type) A
OK (for Key Ring Type) B
NG C




A

REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

B

REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

C

5.CHECK WAVE ENVIRONMENT
a.

Bring the door control transmitter assembly near the main body ECU (fuse block assembly), and perform a wireless operation check.

HINT:
·

When the door control transmitter assembly is brought near the main body ECU (fuse block assembly), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



OK:

Wireless door lock control functions operate normally.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (AFFECTED BY WAVE INTERFERENCE)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)