Home › Drivetrain › A4R AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT › from 2015.08
RM19Y0E _52 Drivetrain _041457 A4R AUTOMATIC TRANSMISSION / TRANSAXLE _0197969 AUTOMATIC TRANSMISSION UNIT A

A4R AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

C153990N01
1.031,0.646 1.625,1.167 0.594,0.521 10 A 5.865,1.563 6.5,2.25 0.635,0.688 10 C 4.375,1.885 4.979,2.531 0.604,0.646 10 B 2.323,3.219 2.917,3.76 0.594,0.542 10 C 0.906,3.458 1.448,4.021 0.542,0.563 10 C 2.094,5.542 2.719,6.125 0.625,0.583 10 D

Mark Thrust Bearing Outside Diameter
mm (in.)
Thrust Bearing Inside Diameter
mm (in.)
A 44.5 (1.752) 29.7 (1.169)
B 30.0 (1.181) 14.0 (0.551)
C 57.0 (2.244) 41.4 (1.630)
D 44.5 (1.752) 29.7 (1.169)

Hide 85420 2.INSTALL TRANSMISSION SOLENOID ASSEMBLY

a.
C331453

Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it to the transmission solenoid assembly.


b.

Install the transmission solenoid assembly with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 35623S 3.INSTALL 1ST AND REVERSE BRAKE PISTON

a.
C153991N01
0.625,0.948 0.396,0.677 false 0.104,0.573 0.802,1.052 0.698,0.479 10 SST

Assemble the brake discs and brake plates on the 1st and reverse brake piston.


b.

Using SST and a press, press the assembly with 6.4 N (0.65 kg, 1.43 lb).

SST
09350-32014  (09351-32040)


c.

Measure the assembly height.

Based on this assembly height, select a suitable flange according to the table below.

Assembly height Part No. Flange thickness Mark
39.450 to 39.661 mm
(1.55314 to 1.56145 in.)
35885-B1010 4.0 mm (0.157 in.) 0
39.250 to 39.450 mm
(1.54527 to 1.55314 in.)
35885-B1020 4.2 mm (0.165 in.) 1
39.050 to 39.250 mm
(1.53740 to 1.54527 in.)
35885-B1030 4.4 mm (0.173 in.) 2
38.850 to 39.050 mm
(1.52952 to 1.53740 in.)
35885-B1040 4.6 mm (0.181 in.) 3
38.650 to 38.850 mm
(1.52165 to 1.52952 in.)
35885-B1050 4.8 mm (0.189 in.) 4
38.439 to 38.650 mm
(1.51334 to 1.52165 in.)
35885-B1060 5.0 mm (0.197 in.) 5


d.
C153992

Coat the 1st and reverse brake piston with Toyota Genuine ATF Type T-IV, and install it to the transmission case.


e.

Install the 1st and reverse brake piston return spring and 1st and reverse brake piston return spring seat.


f.
C267380C01
0.833,0.781 0.573,0.219 true 1.583,2.01 1.219,1.563 true 2.854,1.073 2.854,0.74 true 2.313,0.938 1.938,0.448 true 2.542,0.896 2.604,1.844 2.604,1.844 2.354,1.115 true 0.292,0.115 0.906,0.49 0.615,0.375 10 SST 1.635,1.948 2.354,2.177 0.719,0.229 10 SST 2.74,1.125 3.385,1.542 0.646,0.417 10 SST 1.833,0.292 2.177,0.573 0.344,0.281 10 *a 2.531,1.865 2.875,2.146 0.344,0.281 10 *b
*a Groove
*b Deformation


Place SST on the 1st and reverse brake piston return spring seat and compress the 1st and reverse brake piston return spring.

SST
09351-87201  
09351-97201  

HINT:

To prevent deformation, be sure to stop tightening the SST when the spring has been lowered 1 to 2 mm (0.04 to 0.08 in.) from the snap ring installation groove.



g.
C153980

Using snap ring pliers, install the hole snap ring.


Hide 35775F 4.INSTALL RADIAL BALL BEARING

a.
C153978

Install the radial ball bearing to the transmission case.


Hide 35740A 5.INSTALL FRONT PLANETARY RING GEAR ASSEMBLY

a.
C153993C01
1.781,0.24 2.229,0.135 true 1.781,0.448 2.531,0.469 true 1.896,0.802 2.76,0.906 true 1.771,1.323 2.635,1.583 true 1.625,0.896 1.219,0.375 true 2.25,0.042 2.75,0.458 0.5,0.417 10 *2 2.583,0.385 3.229,0.781 0.646,0.396 10 SST 2.802,0.823 3.427,1.229 0.625,0.406 10 SST 2.688,1.51 3.323,1.906 0.635,0.396 10 SST 1,0.281 1.469,0.688 0.469,0.406 10 *1
*1 Front Planetary Ring Gear Assembly
*2 Press


Using SST and a press, install the front planetary ring gear assembly into the transmission case.

SST
09308-14010  
09309-14010  
09309-35010  


b.
C153994N01
0.969,1.458 1.615,1.885 true 1.688,1.823 2.208,2.167 0.521,0.344 10 A

Install the thrust needle roller bearing to the front planetary ring gear assembly.

HINT:

Be sure to install with the A section of the bearing facing toward the output shaft side.



Hide 35883A 6.INSTALL BRAKE DISC

a.
C334362N01
0.292,0.531 0.594,0.531 false 0.292,0.875 0.594,0.875 false 1.5,0.896 1.5,1.667 1.5,1.667 1.271,1.667 true 0.375,1.104 0.583,1.104 false 0.375,1.344 0.594,1.344 false 1.333,0.885 1.563,0.885 true 0.375,0.875 0.375,1.656 0.375,1.656 0.635,1.656 false 1.323,1.156 1.49,1.156 true 1.323,1.396 1.49,1.396 true 0.167,0.448 0.385,0.635 0.219,0.188 10 false F 1.594,0.823 1.75,1.042 0.156,0.219 10 true D 0.156,0.781 0.375,0.969 0.219,0.188 10 false P

for 1NR-VE

i.

Install the 4 brake plates, 4 brake discs and the brake flange.

Install in order:

P = Brake plate, D = brake disc, F = Brake flange

P - D - P - D - P - D - P - D - F


HINT:
·

Before installing new brake clutch discs, soak them in the Toyota Genuine ATF Type T-IV for at least 15 minutes.

·

Be sure to align the cut-out section of the brake plates and brake flange when installing the brake plate.





b.
C153975N01
0.708,0.25 0.323,0.25 false 0.625,0.656 0.333,0.656 false 0.625,1.625 0.479,1.625 0.479,1.625 0.479,0.656 false 0.625,1.385 0.479,1.385 false 0.625,1.146 0.479,1.146 false 0.625,0.896 0.479,0.896 false 1.354,0.708 1.604,0.708 false 1.344,1.698 1.51,1.698 1.51,1.698 1.51,0.708 false 1.344,1.448 1.51,1.448 false 1.354,1.208 1.51,1.208 false 1.344,0.958 1.51,0.958 false 0.188,0.156 0.75,0.552 0.563,0.396 10 F 1.625,0.615 2.198,1.177 0.573,0.563 10 D 0.188,0.563 0.708,1.104 0.521,0.542 10 P

for 2NR-VE

i.

Install the 5 brake plates, 5 brake discs and the brake flange.

Install in order:

P = Brake plate, D = brake disc, F = Brake flange

P - D - P - D - P - D - P - D - P - D - F


HINT:
·

Before installing new brake discs, soak them in the Toyota Genuine ATF Type T-IV for at least 15 minutes.

·

Be sure to align the cut-out section of the brake plates and brake flange when installing the brake plate.





c.
C153974

Using snap ring pliers, install the hole snap ring.


Hide 35720 7.INSTALL FRONT PLANETARY GEAR ASSEMBLY

a.
C153995

Install the front planetary gear assembly to the transmission case.

HINT:

Ensure that the front planetary gear assembly rotates smoothly.



Hide 35790A 8.INSTALL 1 WAY CLUTCH ASSEMBLY

a.
C153996

Install the 1 way clutch assembly into the transmission case.

HINT:
·

Make sure that the 1 way clutch assembly and the hole snap ring are installed in the correct direction.

·

Align the cut-out section at the inside of the transmission case with the protruding section provided with the matchmarks of the 1 way clutch assembly.




Hide 35624E 9.INSTALL 2ND AND 4TH BRAKE PISTON

a.
C153997N01
0.406,0.625 0.625,0.948 false 0.115,0.521 0.885,1 0.771,0.479 10 SST

Assemble the No. 1 brake flanges, No. 1 brake discs and brake plates on the 2nd and 4th brake piston.


b.

Using SST and a press, press the assembly with 19.6 N (2.00 kg, 4.41 lb).

SST
09350-32014  (09351-32040)


c.

Measure the assembly height.

Based on this assembly height, select a suitable hole snap ring according to the table below.

Assembly height Part No. Snap ring thickness Color
35.66 to 35.91 mm
(1.4039 to 1.4138 in.)
90045-21179 2.25 mm (0.0886 in.) Black
35.91 to 36.16 mm
(1.4138 to 1.4236 in.)
90045-21178 2.00 mm (0.0787 in.) Brown
36.16 to 36.41 mm
(1.4236 to 1.4335 in.)
90045-21177 1.75 mm (0.0689 in.) Blue
36.41 to 36.66 mm
(1.4335 to 1.4433 in.)
90045-21176 1.50 mm (0.0591 in.) Silver


d.
C153998

Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them onto the 2nd and 4th brake piston.


e.
C153999C01
2.375,1.458 1.698,1.646 1.698,1.646 2.469,1.646 true 1.469,1.542 2.021,2.01 0.552,0.469 10 *a
*a Align


Align the claws of the 2nd and 4th brake piston and 2nd and 4th brake cylinder, and install the 2nd and 4th brake piston.

NOTICE:

Do not damage the O-ring.



f.
C153969C02
2.104,1.021 2.375,1.01 false 1.323,0.26 1.083,0.188 false 1.271,1.615 1.01,1.563 false 0.875,0.094 1.51,0.573 0.635,0.479 10 *1 0.781,1.458 1.427,1.906 0.646,0.448 10 *3 2.385,0.896 2.865,1.417 0.479,0.521 10 *2
*1 2nd and 4th Brake Piston Return Spring Seat
*2 2nd and 4th Brake Piston Return Spring
*3 2nd and 4th Brake Piston


Apply Toyota Genuine ATF Type T-IV to the outer periphery of the 2nd and 4th brake cylinder.


g.

Install the 2nd and 4th brake piston return spring seat, 2nd and 4th brake piston return spring, 2nd and 4th brake piston and 2nd and 4th brake cylinder into the transmission case.


h.
C154000

Using 2 screwdrivers, install the hole snap ring.


Hide 35681 10.INSTALL NO. 1 BRAKE DISC

a.
C334361N01
0.25,1.719 0.552,1.719 false 0.25,0.625 0.542,0.625 false 0.271,1.063 0.51,1.063 false 0.354,1.063 0.354,1.375 0.354,1.375 0.51,1.375 false 1.229,0.865 1.438,0.865 true 1.385,0.875 1.385,1.469 1.385,1.469 1.229,1.469 true 1.229,1.188 1.375,1.188 true 0.135,0.542 0.292,0.74 0.156,0.198 10 false F 1.469,0.781 1.625,0.979 0.156,0.198 10 false D 0.135,0.969 0.292,1.167 0.156,0.198 10 false P 0.135,1.625 0.292,1.823 0.156,0.198 10 false F

for 1NR-VE

i.

Install the 2 No. 1 brake flanges, 2 brake plates and 3 No. 1 brake discs.

Install in order:

P = Brake plate, D = No. 1 Brake disc, F = No. 1 Brake flange

F - D - P - D - P - D - F


HINT:
·

Before installing new brake discs, soak them in the Toyota Genuine ATF Type T-IV for at least 15 minutes.

·

Be sure to align the cut-out section of the brake plates and brake flanges when installing the brake plate.





b.
C267381N01
0.25,0.271 0.594,0.271 false 0.24,1.802 0.583,1.802 false 0.25,0.792 0.531,0.792 false 0.542,1.406 0.375,1.406 0.375,1.406 0.375,0.802 false 1.229,1.469 1.365,1.469 1.365,1.469 1.365,0.594 false 1.24,0.594 1.417,0.594 false 1.25,0.917 1.354,0.917 false 1.24,1.208 1.354,1.208 false 0.375,1.115 0.51,1.115 false 0.135,0.188 0.438,0.51 0.302,0.323 10 F 0.125,1.708 0.427,2.031 0.302,0.323 10 F 0.115,0.708 0.438,1.073 0.323,0.365 10 P 1.448,0.5 1.833,0.875 0.385,0.375 10 D

for 2NR-VE

i.

Install the 2 No. 1 brake flanges, 3 brake plates and 4 No. 1 brake discs.

Install in order:

P = Brake plate, D = No. 1 Brake disc, F = No. 1 Brake flange

F - D - P - D - P - D - P - D - F


HINT:
·

Before installing new brake discs, soak them in the Toyota Genuine ATF Type T-IV for at least 15 minutes.

·

Be sure to align the cut-out section of the brake plates and brake flanges when installing the brake plate.





c.
C153966

Using snap ring pliers, install the hole snap ring.


Hide 11.MEASURE BRAKE DISC END PLAY

a.
C153965C02
2.302,1.74 2.167,1.948 true 2.083,1 1.75,0.229 true 1.979,1.938 2.448,2.177 0.469,0.24 10 *1 1.583,0.073 2.104,0.521 0.521,0.448 10 *2
*1 1st and Reverse Brake
*2 2nd and 4th Brake


Using a feeler gauge, measure the 1st and reverse brake and 2nd and 4th brake end play.

Standard end play:
1st and reverse brake:

for 1NR-VE: 0.69 to 1.18 mm (0.0270 to 0.0463 in.)

for 2NR-VE: 0.65 to 1.14 mm (0.0254 to 0.0447 in.)

2nd and 4th brake:

for 1NR-VE: 1.08 to 1.53 mm (0.0424 to 0.0604 in.)

for 2NR-VE: 1.07 to 1.52 mm (0.0420 to 0.0600 in.)


HINT:

If the measured thrust clearance fails to conform to the specified value above, select a snap ring.



Hide 35709K 12.INSTALL REAR PLANETARY GEAR SUB-ASSEMBLY

a.
C267382

Apply Toyota Genuine ATF Type T-IV to the bush section.


b.

Install the rear planetary gear sub-assembly into the transmission case.


Hide 35706V 13.INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C153963C02
0.698,0.302 2.271,0.229 2.271,0.229 0.667,1.552 true 2.333,0.115 2.875,0.521 0.542,0.406 10 *1
*1 Thrust Needle Roller Bearing


Apply Toyota Genuine ATF Type T-IV to the bush section.


b.

Coat the 2 thrust needle roller bearings with petroleum jelly and install them to the planetary sun gear sub-assembly.


c.

Install the planetary sun gear sub-assembly into the transmission case.

HINT:

Check the bearing installation position and direction.



Hide 35631J 14.INSTALL NO. 1 FORWARD CLUTCH HUB

a.
C153962C02
1.667,0.146 2.104,0.115 false 2.177,0.042 2.781,0.542 0.604,0.5 10 *1
*1 Thrust Needle Roller Bearing


Install the thrust needle roller bearing to the No. 1 forward clutch hub.


b.

Install the No. 1 forward clutch hub to the transmission case.

HINT:

Check the bearing installation position and direction.



Hide 35708 15.INSTALL INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C153961C02
1.594,0.198 2.125,0.156 true 2.156,0.073 2.74,0.531 0.583,0.458 10 *1
*1 Thrust Needle Roller Bearing


Install the thrust needle roller bearing to the intermediate shaft sub-assembly.


b.

Install the intermediate shaft sub-assembly to the transmission case.

HINT:

Check the bearing installation position and direction.



Hide 35673 16.INSTALL REAR CLUTCH DISC

a.
C334363N01
1.542,0.094 1.698,0.292 0.156,0.198 10 false F 1.531,1.771 1.688,1.969 0.156,0.198 10 false F 1.531,1.563 1.688,1.76 0.156,0.198 10 false P 1.531,1.344 1.688,1.542 0.156,0.198 10 false P 1.531,1.146 1.688,1.344 0.156,0.198 10 false P 1.531,0.927 1.688,1.125 0.156,0.198 10 false P 1.531,0.708 1.688,0.906 0.156,0.198 10 false P 1.531,0.5 1.688,0.698 0.156,0.198 10 false P 1.531,0.302 1.688,0.5 0.156,0.198 10 false P 0.323,0.198 0.479,0.396 0.156,0.198 10 false D 0.323,0.406 0.479,0.604 0.156,0.198 10 false D 0.323,0.615 0.479,0.813 0.156,0.198 10 false D 0.323,0.823 0.479,1.021 0.156,0.198 10 false D 0.323,1.031 0.479,1.229 0.156,0.198 10 false D 0.323,1.24 0.479,1.438 0.156,0.198 10 false D 0.323,1.448 0.479,1.646 0.156,0.198 10 false D 0.323,1.667 0.479,1.865 0.156,0.198 10 false D

Install the 2 rear clutch flanges, 8 rear clutch discs and 7 No. 3 clutch plates.

Install in order:

P = No. 3 clutch plate, D = Rear clutch disc, F = Rear clutch flange

F - D - P - D - P - D - P - D - P - D - P - D - P - D - P - D - F


HINT:
·

Before installing new rear clutch discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.

·

Be sure to align the cut-out sections of the No. 3 clutch plates and rear clutch flanges when installing them.




b.
C270874

Insert the tip of the hole snap ring into the groove, and install the hole snap ring while compressing it by hand.

NOTICE:

Ensure that the hole snap ring is fitted securely into the groove.



c.
C270875

Using a feeler gauge, measure the rear clutch piston stroke.

Standard piston stroke:

1.03 to 1.34 mm (0.0406 to 0.0528 in.)


If the result is not as specified, replace the hole snap ring with a suitable one by referring to the table below.

Hole snap ring thickness Part No. Color
1.50 mm (0.0591 in.) 90045-21170 Silver
1.75 mm (0.0689 in.) 90045-21171 Blue
2.00 mm (0.0784 in.) 90045-21172 Brown
2.25 mm (0.0886 in.) 90045-21173 Black


Hide 35633F 17.INSTALL FRONT CLUTCH CLUTCH DISC

a.
C183587N01
0.302,0.552 0.458,0.75 0.156,0.198 10 false D 1.479,0.427 1.635,0.625 0.156,0.198 10 false F 1.479,0.635 1.635,0.833 0.156,0.198 10 false P 0.302,0.74 0.458,0.938 0.156,0.198 10 false D 0.302,0.927 0.458,1.125 0.156,0.198 10 false D 0.302,1.125 0.458,1.323 0.156,0.198 10 false D 1.479,0.833 1.635,1.031 0.156,0.198 10 false P 1.479,1.031 1.635,1.229 0.156,0.198 10 false P 1.479,1.219 1.635,1.417 0.156,0.198 10 false P

Install the 4 No. 2 clutch plates, 4 front clutch clutch discs and forward clutch flange.

Install in order:

P = No. 2 clutch plate, D = front clutch clutch disc, F = Forward clutch flange

P - D - P - D - P - D - P - D - F


HINT:
·

Before installing new front clutch clutch discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.

·

Be sure to align the cut-out sections of the forward clutch flange and No. 2 clutch plates when installing them.




b.
C270877

Insert the tip of the hole snap ring into the groove, and install the hole snap ring while compressing it by hand.

NOTICE:

Ensure that the hole snap ring is fitted securely into the groove.



c.
C184585

Using a feeler gauge, measure the forward clutch piston stroke.

Standard piston stroke:

0.67 to 0.98 mm (0.0264 to 0.0386 in.)


If the result is not as specified, replace the hole snap ring with a suitable one by referring to the table below.

Hole snap ring thickness Part No. Color
1.50 mm (0.0591 in.) 90045-21164 Silver
1.75 mm (0.0689 in.) 90045-21166 Blue
2.00 mm (0.0784 in.) 90045-21167 Brown
2.25 mm (0.0886 in.) 90045-21168 Black
2.50 mm (0.0984 in.) 90045-21169 Silver


Hide 35633B 18.INSTALL FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC

a.
C184584N01
0.302,0.781 0.458,0.979 0.156,0.198 10 false D 0.302,0.979 0.458,1.177 0.156,0.198 10 false D 1.448,0.667 1.604,0.865 0.156,0.198 10 false F 1.448,0.896 1.604,1.094 0.156,0.198 10 false P 1.448,1.073 1.604,1.271 0.156,0.198 10 false P

Install the 2 No. 1 clutch plates, 2 forward multiple disc clutch clutch discs and reverse clutch flange.

Install in order:

P = No. 1 clutch plate, D = forward multiple disc clutch clutch disc, F = Reverse clutch flange

P - D - P - D - F


HINT:
·

Before installing new clutch discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.

·

Be sure to align the cut-out sections of the reverse clutch flange and No. 1 clutch plates when installing them.




b.
C270879

Insert the tip of the hole snap ring into the groove, and install the hole snap ring while compressing it by hand.

NOTICE:

Ensure that the hole snap ring is fitted securely into the groove.



Hide 35650 19.INSTALL REAR MULTIPLE DISC CLUTCH ASSEMBLY

a.
C154001

Coat 3 new input shaft oil seal rings with Toyota Genuine ATF Type T-IV, and install them to the rear multiple disc clutch assembly.


b.

Install the rear multiple disc clutch assembly to the transmission case.


c.
C154002C01
2.292,2.667 1.927,2.667 false 1.146,3.646 1.396,3.646 false 1.865,1.417 2.76,2.365 true 2.323,2.573 2.802,3.052 0.479,0.479 10 *a 1.396,3.094 1.969,3.531 0.573,0.438 10 A 1.448,3.563 2.052,4.021 0.604,0.458 10 *b 2.813,2.344 3.281,2.792 0.469,0.448 10 A
*a Installation Section of Front Oil Pump Body
*b Rear Multiple Disc Clutch


Using a vernier caliper, measure height A between the rear multiple disc clutch assembly and the installation section of the front oil pump body sub-assembly.

Standard height:

Approximately 43 mm (1.69 in.)



Hide 35610 20.INSTALL FRONT MULTIPLE DISC CLUTCH ASSEMBLY

a.
C154003

Install the front multiple disc clutch assembly into the transmission case.


b.

Install the thrust needle roller bearing onto the front multiple disc clutch assembly.

NOTICE:

Do not damage the input shaft oil seal rings of the rear multiple disc clutch assembly.



c.
C154004C01
2.76,3.25 2.313,3.063 false 0.667,2.979 1.271,3.156 true 1.583,1.479 2.76,2.375 true 2.813,3.146 3.25,3.698 0.438,0.552 10 *a 2.031,3.073 2.573,3.688 0.542,0.615 10 A 0.458,2.875 0.99,3.385 0.531,0.51 10 *b 2.802,2.333 3.313,2.813 0.51,0.479 10 A
*a Installation Section of Front Oil Pump Body
*b Front Multiple Disc Clutch


Using a vernier caliper, measure height A, marked A, between the front multiple disc clutch assembly and the installation section of the front oil pump body sub-assembly.

Standard height:

Approximately 43.5 mm (1.71 in.)



Hide 35301 21.INSTALL FRONT OIL PUMP BODY SUB-ASSEMBLY

a.
C153957

Install the front oil pump body sub-assembly into the transmission case with the 7 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)

NOTICE:

To prevent the oil seal ring from sticking on the front multiple clutch disc drum, do not press on the front oil pump body sub-assembly hard.



b.
C153956

Using a dial indicator, measure the input shaft end play.

Standard end play:

0.26 to 0.88 mm (0.0102 to 0.0346 in.)


HINT:

There are 3 different thickness bearings for the end of the stator shaft.


If the thrust clearance is not within the standard range, select one of them.

Part No. Bearing thickness
90043-74044 3.41 mm (0.1343 in.)
90043-74043 3.81 mm (0.1500 in.)
90043-74045 4.21 mm (0.1657 in.)


Hide 35595 22.INSTALL PARKING LOCK PAWL BRACKET

a.
C331396

Install the parking lock pawl bracket with the 2 bolts.

Torque:
37.5 N*m (382 kgf*cm, 28 ft.*lbf)


Hide 35557 23.INSTALL PARKING LOCK PAWL

a.

Apply Toyota Genuine ATF Type T-IV to the parking lock pawl shaft.


b.
C331395

Install the parking lock pawl, parking lock pawl shaft and torsion spring.


Hide 35771D 24.INSTALL OUTPUT SHAFT BALL BEARING

a.
C154006C01
1.844,0.104 2.229,0.104 false 2.219,0.604 1.844,0.604 false 2.25,0.51 2.875,0.927 0.625,0.417 10 SST 2.26,0.052 2.781,0.427 0.521,0.375 10 *1
*1 Press


Using SST and a press, install the output shaft ball bearing onto the output shaft sub-assembly.

SST
09309-37010  


Hide 35073 25.INSTALL OUTPUT SHAFT SUB-ASSEMBLY

a.
C154007

Install the output shaft sub-assembly into the transmission case.


Hide 35108 26.INSTALL EXTENSION (ATM) HOUSING SUB-ASSEMBLY

a.

Clean the threads of the bolts and the case with a non-residue solvent.


b.
C331462

Apply FIPG (Diameter 1.5 to 2.5 mm (0.059 to 0.098 in.)) to the extension (ATM) housing sub-assembly as shown in the illustration.

FIPG:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



c.
C331448C02
1.74,0.688 2.49,0.281 true 2.531,0.156 2.823,0.333 0.292,0.177 10 false *1
*1 No. 2 Engine Hanger


Install the extension (ATM) housing sub-assembly and No. 2 engine hanger with the 10 bolts.

Torque:
21.8 N*m (222 kgf*cm, 16 ft.*lbf)


Hide 35108R 27.INSTALL AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

a.
C154009N01
1.875,0.146 2.083,0.542 true 1.594,0.063 2.188,0.458 0.594,0.396 10 SST

Coat a new automatic transmission extension housing oil seal lip with MP grease.


b.

Using SST and a hammer, install the automatic transmission extension housing oil seal.

SST
09325-12010  

Drive in depth:

1.0 to 2.0 mm (0.039 to 0.079 in.)



Hide 33111Q 28.INSTALL TRANSMISSION CASE OIL SEAL

a.
C154010N01
1.406,1.417 1.698,1.667 false 1.75,1.646 2.438,2.052 0.688,0.406 10 SST

Using SST, lightly tap in a new transmission case oil seal into the transmission case.

SST
09612-10093  (09612-10061)

HINT:
·

When properly installed, the oil seal should be flush with the bottom of the oil seal indentation on the transmission case.

·

Be careful not to damage the oil seal.




Hide 35056 29.INSTALL PARKING LOCK WITH ROLLER LEVER SUB-ASSEMBLY

a.
C331398

Apply Toyota Genuine ATF Type T-IV to the parking lock rod sub-assembly.


b.

Install the parking lock rod sub-assembly into the parking lock with roller lever sub-assembly.


c.
C331399

Apply Toyota Genuine ATF Type T-IV to the control shaft.


d.

Install the control shaft into the transmission case.


e.
C331400

Using a pin punch and a hammer, install a new slotted spring pin.


f.
C331393

Using a 3 mm hexagon wrench, install the set bolt.

Torque:
Maximum torque : 3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 35824 30.INSTALL BRAKE CYLINDER SEAL

a.
C184808C04
1.438,1.333 2.563,1.333 true 2.615,1.24 2.927,1.438 0.313,0.198 10 false *1
*1 Brake Cylinder Seal


Coat a new brake cylinder seal with Toyota Genuine ATF Type T-IV, and install it into the transmission case.


Hide 35410 31.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C331389

Connect the connector of the solenoid wire assembly.


b.
C325147N02
1.208,0.229 1.365,0.427 0.156,0.198 10 false A 1.802,0.146 1.958,0.344 0.156,0.198 10 false A 3.177,0.656 3.333,0.854 0.156,0.198 10 false A 2.177,0.125 2.333,0.323 0.156,0.198 10 false B 1.365,3.198 1.521,3.396 0.156,0.198 10 false C 3.188,1.49 3.344,1.688 0.156,0.198 10 false C

Temporarily install the transmission valve body assembly with the 6 bolts.

NOTICE:

Clean the bolts with compressed air before installation.


Bolt length:

35 mm (1.38 in.) for bolt A

45 mm (1.77 in.) for bolt B

16 mm (0.63 in.) for bolt C



c.

Securely tighten the 6 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 35409D 32.INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY

Hide 35303 33.INSTALL OIL STRAINER SUB-ASSEMBLY

Hide 35106 34.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

Hide 84540 35.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C153887C01
2.656,1.26 2.344,1.885 true 2.198,1.896 2.625,2.177 0.427,0.281 10 *1
*1 Transmission Control Shaft Lever


Install the park/neutral position switch assembly to the control shaft.


b.

Temporarily install the bolt.


c.

Temporarily install the transmission control shaft lever sub-assembly.


d.
C153890C04
2.333,0.615 2.823,0.646 true 2.854,0.563 3.323,1.073 0.469,0.51 10 *1
*1 Transmission Control Shaft Lever


Turn the transmission control shaft lever counterclockwise until it stops, and turn it clockwise 2 notches to set it to the N position.


e.

Remove the transmission control shaft lever.


f.
C153889C03
2.115,0.427 2.75,0.26 true 1.938,1.104 2.854,1.188 true 2.771,0.188 3.333,0.646 0.563,0.458 10 *1 2.865,1.104 3.344,1.594 0.479,0.49 10 *a
*1 Notch
*a Neutral Basic Line


Place a ruler tightly against the notch on the control shaft, and adjust the park/neutral position switch assembly until the neutral basic line becomes parallel with the ruler.


g.

Hold the switch in position and tighten the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 35507E 36.INSTALL TRANSMISSION CONTROL SHAFT LEVER

Hide 89413B 37.INSTALL TRANSMISSION REVOLUTION SENSOR

a.
C331441

Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them onto the transmission revolution sensors.


b.

Install the transmission revolution sensor (Input speed sensor) with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


c.

Install the transmission revolution sensor (Output speed sensor) with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 35578B 38.INSTALL TRANSMISSION CONTROL CABLE BRACKET

a.
C331439

Connect the park/neutral position switch connector to the switch harness clamp.


b.

Install the transmission control cable bracket with the 2 bolts.

Torque:
21.8 N*m (222 kgf*cm, 16 ft.*lbf)


Hide 35108C 39.INSTALL AUTOMATIC EXTENSION HOUSING PLUG

a.
C331438

Install the automatic extension housing plug with the hose clamp.