The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body with motor assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.
This Electronic Throttle Control System (ETCS) does not use a throttle cable.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2111 | Throttle Valve Open Stuck | The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic). | ·
Throttle actuator ·
Throttle body with motor assembly ·
Throttle valve ·
Wire harness or connector ·
ECM |
Comes on | DTC stored |
| P2112 | Throttle Valve Close Stuck | The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic). | ·
Throttle actuator ·
Throttle body with motor assembly ·
Throttle valve ·
Wire harness or connector ·
ECM |
Comes on | DTC stored |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Start the engine and fully depress and release the accelerator pedal quickly (to fully open and close the throttle valve).
Enter the following menus: Powertrain / EFI / Trouble Codes [B].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
When either of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.
Refer to DTC P2102.
Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>SFI SYSTEM>P2102
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Refer to "Data List / Active Test" [Relative throttle position, Main accelerator position, Sub accelerator position and Target throttle position].
Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2111 or P2112 is output | A |
| DTC P2111 or P2112 and other DTCs are output | B |
If any DTCs other than P2111 or P2112 are output, troubleshoot those DTCs first.
A
B
Check for contamination between the throttle valve and housing. If necessary, clean the throttle body with motor assembly. Also check that the throttle valve moves smoothly.
Throttle valve is not contaminated with foreign objects and moves smoothly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / EFI / Data List / Main accelerator position, Sub accelerator position and Target throttle position.
Read the values displayed on the GTS while wiggling the ECM wire harness.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| Value in Data List changes when wire harness is wiggled, or DTC is output | A |
| Other than above | B |
A
B
As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the throttle body with motor assembly.
Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>THROTTLE BODY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P2111 or P2112 is output | B |
A
B