The front airbag sensor LH circuit consists of the center airbag sensor assembly and front airbag sensor LH.
The front airbag sensor LH detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1605/15 is stored when a malfunction is detected in the front airbag sensor LH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1605/15 | Passenger seat side FR mechanical sensor malfunctioning | One of the following conditions is met:
·
The center airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor LH circuit. ·
A front airbag sensor LH malfunction. ·
A center airbag sensor assembly malfunction. |
·
Instrument panel wire ·
Engine room main wire ·
Front airbag sensor LH ·
Center airbag sensor assembly |
DTC is not output in check Mode. |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and front airbag sensor LH.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connectors from the center airbag sensor assembly and front airbag sensor LH.
| *1 | Front Airbag Sensor LH |
| *2 | Center Airbag Sensor Assembly |
Check that the connectors (on the center airbag sensor assembly side and front airbag sensor LH side) are not damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
| *1 | Front Airbag Sensor LH | *2 | Center Airbag Sensor Assembly |
| *3 | Connector E | *4 | Connector B |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Front Airbag Sensor LH) |
*b | Rear view of wire harness connector
(to Center Airbag Sensor Assembly) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B14-2 (SLH+) - Body ground | Ignition switch ON | Below 1 V |
| B14-1 (SLH-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 14 (SL+) and 20 (SL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B14-2 (SLH+) - B14-1 (SLH-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B14-2 (SLH+) - B14-1 (SLH+) | Always | 1 MΩ or higher |
| B14-2 (SLH+) - Body ground | Always | 1 MΩ or higher |
| B14-1 (SLH-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the front airbag sensor LH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connectors to the center airbag sensor assembly and front airbag sensor LH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1605/15 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the instrument panel wire connector from the engine room main wire.
| *1 | Front Airbag Sensor LH | *2 | Center Airbag Sensor Assembly |
| *3 | Engine Room Main Wire | *4 | Instrument Panel Wire |
| *5 | Connector C | *6 | Connector B |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Engine Room Main Wire) |
*b | Rear view of wire harness connector
(to Center Airbag Sensor Assembly) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| BE7-1 (SL+) - Body ground | Ignition switch ON | Below 1 V |
| BE7-2 (SL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 14 (SL+) and 20 (SL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| BE7-1 (SL+) - BE7-2 (SL-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| BE7-1 (SL+) - BE7-2 (SL-) | Always | 1 MΩ or higher |
| BE7-1 (SL+) - Body ground | Always | 1 MΩ or higher |
| BE7-2 (-SL-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG