The front passenger side squib circuit consists of the center airbag sensor assembly and the instrument panel passenger airbag assembly.
The circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side squib circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1805/52 | Passenger Seat Frontal Collision Squib Short | One of the following conditions is met:
·
Short in front passenger side squib circuit. ·
Front passenger side squib malfunction. ·
Center airbag sensor assembly malfunction. |
·
Instrument panel wire ·
Instrument panel passenger airbag assembly (front passenger side squib) ·
Center airbag sensor assembly |
DTC is output in check mode |
| B1806/52 | Passenger Seat Frontal Collision Squib Open | One of the following conditions is met:
·
Open in front passenger side squib circuit. ·
Front passenger side squib malfunction. ·
Center airbag sensor assembly malfunction. |
·
Instrument panel wire ·
Instrument panel passenger airbag assembly (front passenger side squib) ·
Center airbag sensor assembly |
DTC is output in check mode |
| B1807/52 | Passenger Seat Frontal Collision Squib GND Short | One of the following conditions is met:
·
Short to ground in front passenger side squib circuit. ·
Front passenger side squib malfunction. ·
Center airbag sensor assembly malfunction. |
·
Instrument panel wire ·
Instrument panel passenger airbag assembly (front passenger side squib) ·
Center airbag sensor assembly |
DTC is output in check mode |
| B1808/52 | Passenger Seat Frontal Collision Squib BATT Short | One of the following conditions is met:
·
Short to B+ in front passenger side squib circuit. ·
Front passenger side squib malfunction. ·
Center airbag sensor assembly malfunction. |
·
Instrument panel wire ·
Instrument panel passenger airbag assembly (front passenger side squib) ·
Center airbag sensor assembly |
DTC is output in check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
To perform the simulation method, enter check mode (signal check) with the intelligent tester or Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
| *1 | Instrument Panel Passenger Airbag Assembly
(Front Passenger Side Squib) |
| *2 | Instrument Panel Wire |
| *3 | Center Airbag Sensor Assembly |
| *4 | Connector C |
| *a | Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib)) |
Disconnect the connector from the instrument panel passenger airbag assembly.
Connect the black wire side of SST (resistance 2.1 Ω) to connector C.
Never connect a tester to the instrument panel passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert the SST into the terminals of the connector when connecting.
Insert the SST straight into the terminals of the connector.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTCs B1805/52, B1806/52, B1807/52 and B1808/52 are not output.
DTCs other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST from connector C.
| *1 | Instrument Panel Passenger Airbag Assembly
(Front Passenger Side Squib) |
| *2 | Center Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
Disconnect the connectors from the center airbag sensor assembly.
Check that the connectors (on the center airbag sensor assembly side and instrument panel passenger airbag side) are not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
| *1 | Instrument Panel Passenger Airbag Assembly
(Front Passenger Side Squib) |
| *2 | Center Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib)) |
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
|---|---|---|
| E61-1 (P+) - Body ground | Ignition switch ON | Below 1 V |
| E61-2 (P-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
|---|---|---|
| E61-1 (P+) - E61-2 (P-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
|---|---|---|
| E61-1 (P+) - E61-2 (P-) | Always | 1 MΩ or higher |
| E61-1 (P+) - Body ground | Always | 1 MΩ or higher |
| E61-2 (P-) - Body ground | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Instrument Panel Passenger Airbag Assembly
(Front Passenger Side Squib) |
| *2 | Center Airbag Sensor Assembly |
Connect the connectors to the instrument panel passenger airbag assembly and the center airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTCs B1805/52, B1806/52, B1807/52 and B1808/52 are not output.
DTCs other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG