Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.09
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0288382 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C0273/13  Motor Relay System Open Wire  


DESCRIPTION

The ABS motor relay supplies power to the ABS pump motor. While the ABS is activated, the skid control ECU (brake actuator assembly) turns the ABS motor relay on and operates the ABS pump motor.

The ABS motor relay is housed in the skid control ECU in the brake actuator assembly.

If the voltage supplied to the motor relay (+BM) is below the DTC detection threshold due to low voltage from the battery or generator, the DTC may be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C0273/13 Motor Relay System Open Wire With ignition switch ON, abnormality occurs in the motor relay and motor relay drive circuit in the brake actuator.
·

ABS fuse

·

Wire harness or connector

·

Decreased power source voltage of motor relay

·

Open or short of motor relay

·

Improperly connected connector, deformation or corrosion of terminals

·

Wire harness or connector


-

WIRING DIAGRAM

C362250E02
1.198,2.063 1.76,2.281 0.563,0.219 10 false Battery 5.521,2.635 7.052,3.063 1.531,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 5.521,2.458 5.865,2.698 0.344,0.24 10 false A13 5.958,1.885 6.458,2.125 0.5,0.24 10 false GND2 5.729,1.75 5.948,2.01 0.219,0.26 10 false 1 5.958,0.667 6.458,0.906 0.5,0.24 10 false +BM 4.219,0.854 4.719,1.094 0.5,0.24 10 false ABS 2.375,0.854 3.115,1.125 0.74,0.271 10 false FL MAIN 5.667,0.552 6.167,0.792 0.5,0.24 10 false 13 4.063,0.563 4.281,0.823 0.219,0.26 10 false 1 4.552,0.563 4.771,0.823 0.219,0.26 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK TERMINAL VOLTAGE (+BM TERMINAL)
C330019C53
1.5,0.167 1.917,0.417 0.417,0.25 2.469,0.51 2.469,0.979 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 1.594,0.208 2.052,0.406 0.458,0.198 10 false A13 2.302,0.302 2.76,0.5 0.458,0.198 10 false +BM
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-13 (+BM) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-25 (GND1) - Body ground Always Below 1 Ω
A13-1 (GND2) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC
HINT:

These codes are detected when a problem is identified in the skid control ECU (brake actuator assembly).

The ABS motor relay is in the skid control ECU (brake actuator assembly). Therefore, the ABS motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).



b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC is not output A
DTC is output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

It is suspected that the DTCs were output due to a bad connection of the connector terminal.





A

B