Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.09
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0288382 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C0278/11  Solenoid Relay System Open  


DESCRIPTION

The ABS solenoid relay supplies power to the ABS solenoid.

After the ignition switch is turned to ON, if the ABS initial check completes, the skid control ECU (brake actuator assembly) turns the ABS solenoid relay on.

The ABS solenoid relay is housed in the skid control ECU in the brake actuator assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C0278/11 Solenoid Relay System Open With ignition switch ON, an open circuit or short to ground occurs in the solenoid valve relay in the brake actuator.
·

ABS fuse

·

Wire harness or connector

·

Open or short in solenoid relay circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

Skid control ECU (brake actuator assembly)


-

WIRING DIAGRAM

C356395E02
0.229,1.198 1.146,1.396 0.917,0.198 10 false from Battery 1.656,1.375 2.115,1.573 0.458,0.198 10 false ABS2 1.594,1.052 1.802,1.219 0.208,0.167 10 false 1 2.021,1.052 2.229,1.219 0.208,0.167 10 false 2 3.25,1.094 3.438,1.281 0.188,0.188 10 false 38 3.25,4.969 3.438,5.156 0.188,0.188 10 false 25 3.542,1.104 3.833,1.281 0.292,0.177 10 false +BS 3.542,4.99 4.115,5.25 0.573,0.26 10 false GND1 4.552,0.99 5.646,1.198 1.094,0.208 10 false Solenoid Relay 4.49,4.094 5.646,4.573 1.156,0.479 10 false Skid Control ECU 5.969,1.313 6.406,1.542 0.438,0.229 10 false SFRH 5.969,1.917 6.427,2.135 0.458,0.219 10 false SFLH 5.969,2.49 6.406,2.719 0.438,0.229 10 false SRRH 5.979,3.083 6.417,3.313 0.438,0.229 10 false SRLH 5.979,3.667 6.417,3.896 0.438,0.229 10 false SFRR 5.979,4.26 6.417,4.49 0.438,0.229 10 false SFLR 5.969,4.844 6.406,5.073 0.438,0.229 10 false SRRR 5.979,5.406 6.417,5.635 0.438,0.229 10 false SRLR 6.021,6 6.458,6.229 0.438,0.229 10 false SM1 6.01,6.594 6.448,6.823 0.438,0.229 10 false SM2 4.323,7.896 6.063,8.104 1.74,0.208 10 false Brake Actuator Assembly 3.958,7.885 4.271,8.083 0.313,0.198 10 false A13

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the skid control (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK TERMINAL VOLTAGE (+BS TERMINAL)
C330019C54
1.51,0.25 1.927,0.5 0.417,0.25 1.906,2.01 2.198,2.01 2.198,2.01 2.438,1.365 true 0.115,0.094 0.427,0.344 0.313,0.25 10 false *a 1.604,0.292 2.073,0.625 0.469,0.333 10 false A13 1.594,1.938 2.104,2.156 0.51,0.219 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator assembly))


a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-38 (+BS) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-25 (GND1) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC
HINT:

These codes are detected when a problem is identified in the skid control ECU (brake actuator assembly).

The solenoid circuit is in the skid control ECU (brake actuator assembly). Therefore, the solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).



b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC is not output A
DTC is output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harnesses and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

It is suspected that the DTCs were output due to a bad connection of the connector terminal.





A

B