Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.09
RM19Y0E _53 Suspension _059025 TIRE PRESSURE MONITORING _0288381 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  ECU Power Source Circuit  


DESCRIPTION

The IG circuit is the power source for the tire pressure warning ECU and receiver.

WIRING DIAGRAM

C364610E01
4.26,2.208 6.927,2.563 2.667,0.354 10 false Tire Pressure Warning ECU and Receiver 3.458,0.792 3.958,1.042 0.5,0.25 10 false IG1 0.979,0.625 2.021,0.99 1.042,0.365 10 false from IG Circuit 5.031,0.625 5.542,0.875 0.51,0.25 10 false IG1 4.76,1.073 5.156,1.333 0.396,0.26 10 false 12 4.802,0.521 5.198,0.781 0.396,0.26 10 false 1 4.823,1.594 5.219,1.854 0.396,0.26 10 false 9 5.021,1.177 5.521,1.427 0.5,0.25 10 false GND 5.021,1.719 5.521,1.969 0.5,0.25 10 false GND3 4.26,2.052 4.76,2.302 0.5,0.25 10 false K6

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - BATTERY AND BODY GROUND)
a.
C363479C02
0.229,0.729 0.729,0.979 0.5,0.25 0.771,1.688 1.208,1.25 true 2.25,1.448 2.74,1.708 true 1.792,1.958 1.625,1.479 true 0.396,0.781 1.01,0.979 0.615,0.198 10 false K6 0.115,0.115 0.729,0.313 0.615,0.198 10 false *a 0.521,1.615 0.865,1.865 0.344,0.25 10 false IG1 2.813,1.625 3.427,1.823 0.615,0.198 10 false GND 1.729,1.979 2.427,2.156 0.698,0.177 10 false GND3
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the tire pressure warning ECU and receiver connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K6-1 (IG1) - Body ground Ignition switch ON 10 to 16 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K6-9 (GND3) - Body ground Always Below 1 Ω
K6-12 (GND) - Body ground Always Below 1 Ω



Result:
Result
OK
NG



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR