Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2016.09
RM19Y0E _59 Vehicle Exterior _003020 LIGHTING (EXT) _0015281 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (fuse block assembly) controls the rear fog lights.

WIRING DIAGRAM

E355646E01
3.927,5.167 6.813,5.563 2.885,0.396 10 false Main Body ECU (Fuse Block Assembly) 0.5,5.125 3.385,5.521 2.885,0.396 10 false Rear Fog Light Switch Assembly 0.688,3.896 3.573,4.292 2.885,0.396 10 false Rear Fog Light Assembly 2.323,3.042 5.208,3.438 2.885,0.396 10 false RR FOG 4.073,0.583 6.958,0.979 2.885,0.396 10 false TAIL 1.542,2.792 4.427,3.188 2.885,0.396 10 false RR FOG 3.375,4.594 6.26,4.99 2.885,0.396 10 false 3F 3.375,1.979 6.26,2.375 2.885,0.396 10 false 16 3.396,4.375 6.281,4.771 2.885,0.396 10 false 21 2.031,4.427 4.917,4.823 2.885,0.396 10 false 3 0.635,4.417 3.521,4.813 2.885,0.396 10 false 4 2.031,3.219 4.917,3.615 2.885,0.396 10 false 2 0.667,3.198 3.552,3.594 2.885,0.396 10 false 1 2.188,2.01 5.073,2.406 2.885,0.396 10 false 2 2.917,2.438 5.802,2.833 2.885,0.396 10 false 5 2.917,2 5.802,2.396 2.885,0.396 10 false 1 2.177,2.458 5.063,2.854 2.885,0.396 10 false 3 1.229,0.406 4.115,0.802 2.885,0.396 10 false from Battery 0.438,2.583 3.323,2.979 2.885,0.396 10 false from Battery 1.76,4.469 4.646,4.865 2.885,0.396 10 false + 0.885,4.458 3.771,4.854 2.885,0.396 10 false - 1.781,3.365 4.667,3.76 2.885,0.396 10 false + 0.906,3.375 3.792,3.771 2.885,0.396 10 false - 4.802,1.635 7.156,2.031 2.354,0.396 10 false TAIL 3.385,2.188 6.271,2.583 2.885,0.396 10 false 3F 3.396,1.74 6.281,2.135 2.885,0.396 10 false 3I 3.427,1.531 6.313,1.927 2.885,0.396 10 false 2 3.375,0.417 6.26,0.813 2.885,0.396 10 false 3A 3.417,0.198 6.302,0.594 2.885,0.396 10 false 1 6.021,2.188 7.156,2.667 1.135,0.479 10 false RL03 6.021,0.938 7.156,1.417 1.135,0.479 10 false TAILO 6.021,4.604 7.156,5.083 1.135,0.479 10 false MCSW 0.51,4.958 1.646,5.438 1.135,0.479 10 false E94 0.708,3.74 1.844,4.219 1.135,0.479 10 false Q3 2.323,2.885 5.208,3.281 2.885,0.396 10 false E97

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (RR FOG LAMP)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Body / Active Test.


e.

According to the display on the GTS or Techstream, perform the Active Test.

Body Electrical / Body / Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rr fog lamp Rear fog light relay ON/OFF -

OK:

Rear fog light relay operates (Rear fog lights illuminate).


Result:
Proceed to
OK
NG




OK

2.INSPECT REAR FOG LIGHT SWITCH ASSEMBLY

NG

4.INSPECT REAR FOG LIGHT RELAY
2.INSPECT REAR FOG LIGHT SWITCH ASSEMBLY
a.

Remove the rear fog light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR FOG LIGHT SWITCH>REMOVAL


b.

Inspect the rear fog light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR FOG LIGHT SWITCH>INSPECTION

Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - REAR FOG SWITCH ASSEMBLY)

NG

REPLACE REAR FOG LIGHT SWITCH

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - REAR FOG SWITCH ASSEMBLY)
a.

Disconnect the E94 rear fog switch assembly connector.


b.

Disconnect the 3F main body ECU (fuse block assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E94-3(+) - 3F-21 Always Below 1 Ω
E94-4(-) - Body ground Always Below 1 Ω
E94-3(+) or 3F-21 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT REAR FOG LIGHT RELAY
a.

Remove the rear fog light relay.


b.

Inspect the rear fog light relay.

Click hereVehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - REAR FOG LIGHT RELAY)

NG

REPLACE REAR FOG LIGHT RELAY

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - REAR FOG LIGHT RELAY)
a.

Disconnect the E97 rear fog light relay connector.


b.

Disconnect the 3F main body ECU (fuse block assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3F-16 - E97-1 Always Below 1 Ω
3F-16 or E97-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - BATTERY)
a.

Remove the rear fog light assembly.


b.
E356637C01
1.438,0.25 2.021,0.5 0.583,0.25 0.354,0.25 0.667,0.448 0.313,0.198 10 false *a 1.615,0.302 1.927,0.5 0.313,0.198 10 false E97
*a Front view of wire harness connector
(to Rear Fog Light Relay connector)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E97-2 - Body ground Headlight dimmer switch assembly (light control switch) in tail position 11 to 14 V
E97-3 - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

7.INSPECT REAR FOG LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT REAR FOG LIGHT ASSEMBLY
a.

Remove the rear fog light assembly.


b.

Inspect the rear fog light assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR FOG LIGHT SWITCH>INSPECTION

Result:
Proceed to
OK
NG




OK

8.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - REAR FOG LIGHT ASSEMBLY)

NG

REPLACE REAR FOG LIGHT ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - REAR FOG LIGHT ASSEMBLY)
a.

Disconnect the E97 rear fog light relay connector.


b.

Disconnect the Q3 rear fog light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E97-5 - Q3-2(+) Always Below 1 Ω
Q3-1(-) - Body ground Always Below 1 Ω
E97-5 or Q3-2(+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR