Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2016.10–2018.05
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292486 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A8111  Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground  


DESCRIPTION

The battery cooling blower assembly speed is controlled by the hybrid vehicle control ECU. Power is supplied to the battery cooling blower assembly when the MREL terminal of the hybrid vehicle control ECU turns on the IGCT relay. The hybrid vehicle control ECU sends command signals (SI0) to the battery cooling blower assembly to adjust the fan speed to an appropriate speed for the HV battery temperature. The frequency (FP0) of the battery cooling blower assembly is sent to the hybrid vehicle control ECU via the battery voltage sensor as a monitor signal using serial communication.

A260101E32
0.521,0.208 2.594,0.646 2.073,0.438 10 false Battery Cooling Blower Assembly 2.792,0.958 4.417,1.323 1.625,0.365 10 false SI0 (Command Signal) 2.865,3.198 4.531,3.521 1.667,0.323 10 false FP0 (Monitor Signal) 4.875,0.385 5.771,1.021 0.896,0.635 10 false Hybrid Vehicle Control ECU 4.833,2.354 5.813,2.802 0.979,0.448 10 false Battery Voltage Sensor 3.896,1.729 5.281,2.01 1.385,0.281 10 false Serial Communication

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A8111 Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground Both of the following conditions are met:
·

The speed calculated based on the battery cooling blower assembly output frequency is not within the target control speed range.

·

The battery cooling blower assembly speed is excessively low when a certain level of speed is requested (possibility of an open or short to ground in connected circuits, or motor locking).


(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid vehicle control ECU

·

Battery cooling blower assembly

·

BATT FAN fuse

·

Wire harness or connector


Does not come on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0A8111
·

Hybrid Battery Cooling Fan Drive Request

·

Hybrid Battery Cooling Fan 1 Drive Status

·

Hybrid Battery Cooling Fan Frequency



The following items can be helpful when performing repairs:

Data List
·

Hybrid Battery Temperature 1 to 3

·

BATT Voltage


HINT:

"Hybrid Battery Cooling Fan Frequency" is detected when the battery cooling blower assembly is operating and its value changes in proportion to the battery cooling blower assembly speed.


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

7.

Select fan mode 6 and operate the battery cooling blower assembly and wait for 10 seconds or more.

HINT:

Operation of the battery cooling blower assembly can be confirmed by checking if air is sucked into the air intake port of the intake duct.


8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A394808E01
0.552,0.323 3.156,0.521 2.604,0.198 10 false Auxiliary Battery 2.271,0.469 2.969,0.719 0.698,0.25 10 false IGCT-IG 3.406,1.052 4.104,1.302 0.698,0.25 10 false IGCT 4.49,0.458 5.24,0.729 0.75,0.271 10 false BATT FAN 5.021,0.219 5.177,0.417 0.156,0.198 10 false 2 4.583,0.219 4.74,0.417 0.156,0.198 10 false 1 3.115,0.219 3.271,0.417 0.156,0.198 10 false 3 3.115,0.635 3.271,0.833 0.156,0.198 10 false 1 3.927,0.219 4.083,0.417 0.156,0.198 10 false 5 3.927,0.635 4.083,0.833 0.156,0.198 10 false 2 1.656,1.385 2.354,1.635 0.698,0.25 10 false MREL 1.844,1.917 2.542,2.167 0.698,0.25 10 false SI0 1.698,4.052 2.396,4.302 0.698,0.25 10 false BTH+ 1.729,4.531 2.427,4.781 0.698,0.25 10 false BTH- 0.927,4.073 1.625,4.323 0.698,0.25 10 false E01 0.927,4.563 1.625,4.813 0.698,0.25 10 false E02 2.208,1.458 2.906,1.708 0.698,0.25 10 false A48 2.26,2.01 2.958,2.26 0.698,0.25 10 false F3 2.26,4.052 2.958,4.302 0.698,0.25 10 false F2 2.26,4.531 2.958,4.781 0.698,0.25 10 false F2 0.573,4.073 1.271,4.323 0.698,0.25 10 false F2 0.573,4.563 1.271,4.813 0.698,0.25 10 false F3 2.302,1.271 3,1.521 0.698,0.25 10 false 6 2.271,1.813 2.969,2.063 0.698,0.25 10 false 29 2.271,3.854 2.969,4.104 0.698,0.25 10 false 32 2.271,4.333 2.969,4.583 0.698,0.25 10 false 33 0.625,4.375 1.323,4.625 0.698,0.25 10 false 5 0.625,3.875 1.323,4.125 0.698,0.25 10 false 5 5.604,5.125 7.125,5.406 1.521,0.281 10 false Battery Voltage Sensor 5.604,4.958 6,5.177 0.396,0.219 10 false M41 3.25,2.448 3.948,2.698 0.698,0.25 10 false GND0 3.25,1.917 3.948,2.167 0.698,0.25 10 false SI0 4.417,2.448 5.115,2.698 0.698,0.25 10 false FP0 4.458,1.917 5.156,2.167 0.698,0.25 10 false IG0 3.021,1.917 3.177,2.115 0.156,0.198 10 false 4 3.021,2.448 3.177,2.646 0.156,0.198 10 false 3 4.813,1.917 4.969,2.115 0.156,0.198 10 false 2 4.813,2.448 4.969,2.646 0.156,0.198 10 false 1 3.26,3.083 4.719,3.583 1.458,0.5 10 false Battery Cooling Blower Assembly 3.26,2.927 3.958,3.177 0.698,0.25 10 false M43 5.854,2.448 6.271,2.635 0.417,0.188 10 false FP0 5.854,4.083 6.292,4.26 0.438,0.177 10 false BTH+ 5.854,4.563 6.292,4.771 0.438,0.208 10 false BTH- 5.625,2.448 5.948,2.625 0.323,0.177 10 false 8 5.625,3.979 6.021,4.167 0.396,0.188 10 false 2 5.625,4.458 5.99,4.646 0.365,0.188 10 false 3 0.625,5.083 2.625,5.573 2,0.49 10 false Hybrid Vehicle Control ECU

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery



·
A371653

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A371654C01
1.563,1.229 1.333,0.813 true 1.156,0.677 1.469,0.875 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

As the battery cooling blower assembly speed is excessively low, there is a possibility of an open or short to ground in connected circuits, or motor locking.


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
P0AFC00 or P0AFC96 is not output. A
P0AFC00 or P0AFC96 is also output. B


e.

Turn the power switch off.



A

2.PERFORM ACTIVE TEST USING GTS (DRIVING THE BATTERY COOLING FAN)

B

2.PERFORM ACTIVE TEST USING GTS (DRIVING THE BATTERY COOLING FAN)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Clear DTCs
50002 397

d.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.

Powertrain > Hybrid Control > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid Battery Cooling Fan Battery cooling blower assembly operation and blower volume can be checked. OFF, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > Hybrid Control > Active Test
Tester Display
Control the Hybrid Battery Cooling Fan
50004 397 2

e.

Select air volume mode 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check if the fan operates and air is sucked. In accordance with fail-safe system operation, the hybrid vehicle control ECU sends a command to operate the battery cooling blower assembly.



f.

Check that the battery cooling blower assembly operates, air is sucked into the inlet duct and the operation sound is normal.

HINT:

The battery cooling blower assembly may not stop even when turning the cooling fan off in the "Control the Hybrid Battery Cooling Fan" Active Test. This is due to HV system control and is not a malfunction.



g.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY)

NG

7.CHECK FUSE (BATT FAN)
3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


c.

Disconnect the battery voltage sensor connector.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A376400N04
1.885,0.75 2.292,1.042 0.406,0.292 1.917,0.781 2.26,1.021 0.344,0.24 10 true M43

Disconnect the battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A368047C04
1.448,2.125 1.906,2.396 0.458,0.271 0.781,3.542 1.24,3.813 0.458,0.271 1.896,3.51 2.354,3.281 true 1.906,2.635 2.365,2.406 true 0.135,0.115 0.594,0.604 0.458,0.49 10 false *a 0.24,3.021 0.604,3.323 0.365,0.302 10 false *b 0.885,3.583 1.406,3.885 0.521,0.302 10 false M43 1.563,2.177 2.083,2.479 0.521,0.302 10 false M41 2.427,3.156 2.792,3.458 0.365,0.302 10 false FP0 1.615,2.604 1.979,2.906 0.365,0.302 10 false FP0
*a Rear view of wire harness connector
(to Battery Voltage Sensor)
*b Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M41-8 (FP0) - M43-1 (FP0) Power switch off Below 1 Ω
M41-8 (FP0) - Body ground and other terminals Power switch off 10 kΩ or higher



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M41-8 (FP0) - Body ground Power switch on (IG) Below 1 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

Check that each connector between the battery voltage sensor and battery cooling blower assembly is not loose or disconnected.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the battery cooling blower assembly connector.


l.

Reconnect the battery voltage sensor connector.


m.

Install the No. 1 HV battery shield panel.


Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (COOLING FAN FREQUENCY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (COOLING FAN FREQUENCY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Connect the GTS to the DLC3.


e.

Turn the power switch on (IG).


f.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


g.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

h.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.

Powertrain > Hybrid Control > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid Battery Cooling Fan Battery cooling blower assembly operation and blower volume can be checked. OFF, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > Hybrid Control > Active Test
Tester Display
Control the Hybrid Battery Cooling Fan
50004 397 2

i.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Cooling Fan Frequency.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Cooling Fan Frequency
50003 397 157

j.

Select each air volume mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

NOTICE:

If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the hybrid vehicle control ECU sends a command to operate the battery cooling fan assembly.



k.
A368051C35
2.167,0.156 2.604,0.385 0.438,0.229 1.719,1.635 2.26,0.948 true 2.781,1.698 2.49,0.958 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.26,0.177 2.656,0.49 0.396,0.313 10 false M41 1.552,1.656 1.885,1.917 0.333,0.26 10 false FP0 2.688,1.719 3.021,1.979 0.333,0.26 10 false GND
*a Component with harness connected
(Battery Voltage Sensor)


While the cooling fan is operating, compare the value in the Data List (Hybrid Battery Cooling Fan Frequency) with the frequency value that was actually measured at the battery voltage sensor connector.

Specified Condition:
Tester Connection Condition
M41-8 (FP0) - M41-5 (GND) Battery cooling blower assembly is operating.


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each air volume mode 1 to 6. If the Active Test cannot be performed, compare the values only in the current air volume mode.



Result:
Result Proceed to
Both of the value in the Data List (Hybrid Battery Cooling Fan Frequency) and the actual measured value at the battery voltage sensor connector are 0 Hz. A
Other than above B


l.

Turn the power switch off.


m.

Disconnect the cable from the negative (-) auxiliary battery terminal.


n.

Install the No. 1 HV battery shield panel.



A

5.CHECK BATTERY VOLTAGE SENSOR

B

6.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)
5.CHECK BATTERY VOLTAGE SENSOR
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


c.
A376400N04
1.885,0.75 2.292,1.042 0.406,0.292 1.917,0.781 2.26,1.021 0.344,0.24 10 true M43

Disconnect the battery cooling bower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A369910C21
1.542,0.333 2.042,0.583 0.5,0.25 1.99,0.979 2.448,0.719 true 1.99,1.229 2.479,1.521 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.656,0.354 2.313,0.875 0.656,0.521 10 false M43 2.531,0.594 3.115,1.219 0.583,0.625 10 false FP0 2.552,1.531 3.104,1.844 0.552,0.313 10 false GND0
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M43-1 (FP0) - M43-3 (GND0) Power switch on (IG) 4.5 to 5.5 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the battery cooling blower assembly connector.


j.

Install the rear seat cushion assembly.


Result:
Proceed to
OK
NG



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

6.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Connect the GTS to the DLC3.


e.

Turn the power switch on (IG).


f.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


g.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

h.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.

Powertrain > Hybrid Control > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid Battery Cooling Fan Battery cooling blower assembly operation and blower volume can be checked. OFF, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > Hybrid Control > Active Test
Tester Display
Control the Hybrid Battery Cooling Fan
50004 397 2

i.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Cooling Fan Frequency.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Cooling Fan Frequency
50003 397 157

j.

Select each air volume mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

NOTICE:

If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the hybrid vehicle control ECU sends a command to operate the battery cooling blower assembly.



k.
A368051C36
2.167,0.156 2.604,0.385 0.438,0.229 1.719,1.635 2.26,0.948 true 2.781,1.698 2.49,0.958 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.26,0.177 2.656,0.49 0.396,0.313 10 false M41 1.552,1.656 1.885,1.917 0.333,0.26 10 false FP0 2.688,1.719 3.021,1.979 0.333,0.26 10 false GND
*a Component with harness connected
(Battery Voltage Sensor)


While the cooling fan is operating, compare the value in the Data List (Hybrid Battery Cooling Fan Frequency) with the frequency value that was actually measured at the battery voltage sensor connector.

Specified Condition:
Tester Connection Condition Specified Condition
M41-8 (FP0) - M41-5 (GND) Battery cooling blower assembly is operating. Difference between the value in the Data List (Hybrid Battery Cooling Fan Frequency) and the actual measured value at the battery voltage sensor connector is 10% or less.


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each air volume mode 1 to 6. If the Active Test cannot be performed, compare the values only in the current air volume mode.



Result:
Proceed to
OK
NG


l.

Turn the power switch off.


m.

Disconnect the cable from the negative (-) auxiliary battery terminal.


n.

Install the No. 1 HV battery shield panel.



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

7.CHECK FUSE (BATT FAN)
a.
A389510C01
2.656,1.99 1.74,1.427 true 0.354,0.167 0.667,0.365 0.313,0.198 10 false *1 2.656,2.031 2.969,2.229 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 BATT FAN Fuse


Remove the BATT FAN fuse from the No. 1 engine room relay block.


b.

Measure the resistance of the BATT FAN fuse.

Standard Resistance:
Tester Connection Condition Specified Condition
BATT FAN fuse Power switch off Below 1 Ω



c.

Install the BATT FAN fuse to the No. 1 engine room relay block.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY) (VOLTAGE)

NG

17.CHECK HARNESS AND CONNECTOR (BATT FAN FUSE - BATTERY COOLING BLOWER ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY) (VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


c.
A376400N04
1.885,0.75 2.292,1.042 0.406,0.292 1.917,0.781 2.26,1.021 0.344,0.24 10 true M43

Disconnect the battery cooling bower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Connect the GTS to the DLC3.


f.

Turn the power switch on (IG).


g.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


h.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

i.
A369910C71
1.552,0.333 2.052,0.583 0.5,0.25 1.042,0.781 1.583,1 true 2,1.24 2.5,1.5 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.656,0.365 2.073,0.552 0.417,0.188 10 false M43 0.729,0.688 1.313,1.313 0.583,0.625 10 false IG0 2.531,1.51 3.198,1.719 0.667,0.208 10 false GND0
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M43-2 (IG0) - M43-3 (GND0) Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

·

Installation condition of fuse(s) (before removing fuse(s)) (IG circuit)

·

Fuse condition (before and after removing fuse(s)) (IG circuit)

·

Connection condition of connectors (IG circuit)

·

Wire harness condition (IG circuit)

·

Wire harness condition (GND circuit)




j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.


l.

Install the rear seat cushion assembly.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY COOLING BLOWER ASSEMBLY)

NG

13.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BODY GROUND)
9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the hybrid vehicle control ECU connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the hybrid vehicle control ECU and battery cooling blower assembly is not loose or disconnected.




c.

Remove the rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


d.
A376400N04
1.885,0.75 2.292,1.042 0.406,0.292 1.917,0.781 2.26,1.021 0.344,0.24 10 true M43

Disconnect the battery cooling blower assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




e.
A389511C01
2.365,0.333 2.865,0.583 0.5,0.25 0.75,3.5 1.25,3.75 0.5,0.25 2.833,2.75 2.635,2.229 true 1.167,4.167 1.5,3.781 true 0.25,0.167 0.563,0.323 0.313,0.156 10 false *a 0.25,3.167 0.563,3.323 0.313,0.156 10 false *b 2.781,2.802 3.198,2.969 0.417,0.167 10 false SI0 1.052,4.208 1.469,4.375 0.417,0.167 10 false SI0 0.865,3.521 1.323,3.719 0.458,0.198 10 false M43 2.531,0.354 2.99,0.552 0.458,0.198 10 false F3
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-29 (SI0) - M43-4 (SI0) Power switch off Below 1 Ω
M43-4 (SI0) - Body ground and other terminals Power switch off 10 kΩ or higher


NOTICE:

Make sure that each connector between the hybrid vehicle control ECU and battery cooling blower assembly is not loose or disconnected and its terminals are not deformed or corroded.



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M43-4 (SI0) - Body ground Power switch on (IG) Below 1 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

Check that each connector between the hybrid vehicle control ECU and battery cooling blower assembly is not loose or disconnected.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the battery cooling blower assembly connector.


l.

Install the rear seat cushion assembly.


m.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

10.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HYBRID VEHICLE CONTROL ECU

b.
A394817C04
1.802,0.583 2.302,0.833 0.5,0.25 2.396,0.583 2.896,0.833 0.5,0.25 1.5,2.25 1.896,1.417 true 2.917,2.25 2.625,1.625 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.969,0.615 2.281,0.813 0.313,0.198 10 false F2 2.573,0.615 2.885,0.813 0.313,0.198 10 false F3 1.333,2.26 1.646,2.458 0.313,0.198 10 false E01 2.813,2.26 3.125,2.458 0.313,0.198 10 false SI0
*a Component without harness connected
(Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-29 (SI0) - F2-5 (E01) Power switch off 10 kΩ or higher



c.

Install the hybrid vehicle control ECU.


Result:
Proceed to
OK
NG



OK

11.CHECK HYBRID VEHICLE CONTROL ECU (SI0 VOLTAGE)

NG

11.CHECK HYBRID VEHICLE CONTROL ECU (SI0 VOLTAGE)
a.

Turn the power switch on (IG).


b.
A418457C01
1.802,0.833 2.302,1.083 0.5,0.25 2.385,0.833 2.885,1.083 0.5,0.25 1.667,2.583 1.896,1.719 true 2.813,2.583 2.604,1.906 true 0.115,0.073 0.427,0.229 0.313,0.156 10 false *a 2.563,0.865 2.875,1.021 0.313,0.156 10 false F3 1.979,0.854 2.292,1.01 0.313,0.156 10 false F2 1.542,2.594 1.854,2.75 0.313,0.156 10 false E01 2.74,2.594 3.052,2.75 0.313,0.156 10 false SI0
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F3-29 (SI0) - F2-5 (E01) Power switch on (IG) 4.5 to 5.5 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

12.CHECK BATTERY COOLING BLOWER ASSEMBLY

NG

REPLACE BATTERY COOLING BLOWER ASSEMBLY

12.CHECK BATTERY COOLING BLOWER ASSEMBLY
a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

f.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.

Powertrain > Hybrid Control > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid Battery Cooling Fan Battery cooling blower assembly operation and blower volume OFF, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > Hybrid Control > Active Test
Tester Display
Control the Hybrid Battery Cooling Fan
50004 397 2

g.

Select each air volume mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

NOTICE:

If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the waveform. In accordance with fail-safe system operation, the hybrid vehicle control ECU sends a command to operate the battery cooling blower assembly.



h.
A389500C04
2.375,0.833 2.875,1.083 0.5,0.25 1.792,0.833 2.292,1.083 0.5,0.25 1.74,2.417 1.885,1.719 true 2.823,2.615 2.615,1.917 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.635,2.469 2.021,2.667 0.385,0.198 10 false E01 2.781,2.656 3.344,2.823 0.563,0.167 10 false SI0 1.969,0.865 2.354,1.063 0.385,0.198 10 false F2 2.552,0.865 2.938,1.063 0.385,0.198 10 false F3
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Connect an oscilloscope to the F2 and F3 hybrid vehicle control ECU connectors and check the waveform.

Item Content
Tester Connection F3-29(SI0) - F2-5(E01)
Equipment Setting 10 V/DIV., 1 ms./DIV.
Condition Power switch on (IG), during Active Test

HINT:
·

Perform this inspection with the hybrid vehicle control ECU connector connected.

·

The wave length will vary with the operating speed of the battery cooling blower assembly.




i.

Turn the power switch off.


j.
A284431C05
2.938,1.031 3.396,1.229 0.458,0.198 10 false GND 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a
*a Waveform 1


Disconnect the cable from the negative (-) auxiliary battery terminal.


Result:
Result Proceed to
Normal (The pulse output of waveform 1) A
No pulse generation B



A

REPLACE BATTERY COOLING BLOWER ASSEMBLY

B

13.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


c.
A376400N09
1.885,0.75 2.292,1.042 0.406,0.292 1.917,0.781 2.26,1.021 0.344,0.24 10 true M43

Disconnect the battery cooling blower assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




d.
A369910C55
1.583,0.354 2.021,0.635 0.438,0.281 1.969,1.229 2.51,1.448 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.688,0.385 2.344,0.906 0.656,0.521 10 false M43 2.583,1.427 3.219,1.813 0.635,0.385 10 false GND0
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-3 (GND0) - Body ground Power switch off Below 1 Ω



e.

Reconnect the battery cooling blower assembly connector.


f.

Install the rear seat cushion assembly.


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
a.

Disconnect the hybrid vehicle control ECU connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



b.
A389503C01
1.792,0.583 2.292,0.833 0.5,0.25 1.5,2.833 1.885,2.417 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.344,2.875 1.76,3.031 0.417,0.156 10 false E01 1.958,0.615 2.375,0.771 0.417,0.156 10 false F2
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-5 (E01) - Body ground Power switch off Below 1 Ω



c.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
a.

Disconnect the hybrid vehicle control ECU connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



b.
A389504C01
2.385,0.5 2.885,0.75 0.5,0.25 2.25,2.667 2.604,2.26 true 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 2.083,2.719 2.479,2.875 0.396,0.156 10 false E02 2.552,0.521 2.865,0.719 0.313,0.198 10 false F3
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-5 (E02) - Body ground Power switch off Below 1 Ω



c.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the IGCT relay from the No. 1 engine room relay block.

NOTICE:

Check the terminals of the relay for deformation and corrosion.



c.

Remove the rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


d.
A376400N04
1.885,0.75 2.292,1.042 0.406,0.292 1.917,0.781 2.26,1.021 0.344,0.24 10 true M43

Disconnect the battery cooling blower assembly connector.

NOTICE:
·

Check that each connector between the IGCT relay and battery cooling blower assembly is not loose or disconnected.

·

Before disconnecting the connector, check that it is not loose or disconnected.




e.
A389512C01
0.417,0.25 0.917,0.5 0.5,0.25 0.75,0.75 1.115,0.49 true 0.104,1.167 0.417,1.323 0.313,0.156 10 false *1 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 2.146,2.75 2.458,2.906 0.313,0.156 10 false *b 0.604,0.792 0.917,0.948 0.313,0.156 10 false IG0 0.552,0.26 1.01,0.458 0.458,0.198 10 false M43
*1 No. 1 Engine Room Relay Block
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)
*b IGCT Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGCT relay holder) - M43-2 (IG0) Power switch off Below 1 Ω


NOTICE:
·

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

·

Check that each connector between the IGCT relay and battery cooling blower assembly is not loose or disconnected.




f.

Reconnect the battery cooling blower assembly connector.


g.

Install the rear seat cushion assembly.


h.

Install the IGCT relay to the No. 1 engine room relay block.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (BATT FAN FUSE - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the BATT FAN fuse from the No. 1 engine room relay block.


c.

Remove the rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


d.
A376400N04
1.885,0.75 2.292,1.042 0.406,0.292 1.917,0.781 2.26,1.021 0.344,0.24 10 true M43

Disconnect the battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A389513C01
0.417,0.25 0.917,0.5 0.5,0.25 0.75,0.833 1.115,0.49 true 0.073,1.125 0.385,1.281 0.313,0.156 10 false *1 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 2.198,2.281 2.51,2.438 0.313,0.156 10 false *b 0.604,0.885 0.917,1.042 0.313,0.156 10 false IG0 0.542,0.271 1,0.469 0.458,0.198 10 false M43
*1 No. 1 Engine Room Relay Block
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)
*b BATT FAN Fuse Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-2 (IG0) - Terminals other than 2 (BATT FAN fuse holder) and body ground Power switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



f.

Reconnect the battery cooling blower assembly connector.


g.

Install the rear seat cushion assembly.


h.

Install the BATT FAN fuse to the No. 1 engine room relay block.


Result:
Proceed to
OK
NG



OK

18.CHECK BATTERY COOLING BLOWER ASSEMBLY

NG

20.REPAIR OR REPLACE HARNESS OR CONNECTOR
18.CHECK BATTERY COOLING BLOWER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


c.
A376400N04
1.885,0.75 2.292,1.042 0.406,0.292 1.917,0.781 2.26,1.021 0.344,0.24 10 true M43

Disconnect the battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A369912C08
1.479,0.25 1.979,0.5 0.5,0.25 0.99,1.479 1.552,1.229 true 1.938,0.979 2.5,0.729 true 0.208,0.115 0.781,0.625 0.573,0.51 10 false *a 1.594,0.26 2.167,0.771 0.573,0.51 10 false M43 2.583,0.635 3.156,1.146 0.573,0.51 10 false IG0 0.531,1.396 1.104,1.906 0.573,0.51 10 false GND0
*a Component without harness connected
(Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-2 (IG0) - M43-3 (GND0) and Body ground Power switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



e.

Reconnect the battery cooling blower assembly connector.


f.

Install the rear seat cushion assembly.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (BATT FAN)

NG

19.REPLACE BATTERY COOLING BLOWER ASSEMBLY
19.REPLACE BATTERY COOLING BLOWER ASSEMBLY

NEXT

REPLACE FUSE (BATT FAN)

20.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (BATT FAN)