Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2016.10–2018.05
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292486 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0ABF11  Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground  P0ABF15  Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open  P1CBB12  Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery  P1CBB14  Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open  


DESCRIPTION

A battery current sensor is installed to the positive (+) terminal side of the HV battery and detects current flowing from the HV battery. The battery current sensor outputs voltage, which changes between 0 and 5 V according to the detected amperage, to the IB terminal of the battery voltage sensor. The battery voltage sensor sends signals to the hybrid vehicle control ECU. The hybrid vehicle control ECU determines the charging and discharging amount of the HV battery based on the received signals and calculates the SOC of the HV battery through the accumulated amperage.

A304993E21
0.052,0.073 0.625,0.521 0.573,0.448 10 false Charging Current 0.719,0.083 1.479,0.552 0.76,0.469 10 false Discharging Current 0.875,1.01 2.563,1.25 1.688,0.24 10 false Battery Current Sensor 2.094,2.677 3.688,2.948 1.594,0.271 10 false Battery Voltage Sensor 2.406,1.26 2.865,1.458 0.458,0.198 10 false VIB 2.417,1.563 2.729,1.76 0.313,0.198 10 false IB 2.406,1.865 2.865,2.063 0.458,0.198 10 false GIB 3.177,0.104 6,0.323 2.823,0.219 10 false Battery Current Sensor Output Voltage 3.969,0.469 4.427,0.667 0.458,0.198 10 false (V) 3.958,0.865 4.417,1.063 0.458,0.198 10 false 4.5 3.969,1.594 4.427,1.792 0.458,0.198 10 false 2.5 3.969,2.323 4.427,2.521 0.458,0.198 10 false 0.5 4.25,2.625 4.865,2.823 0.615,0.198 10 false -200 5.594,2.625 5.75,2.823 0.156,0.198 10 false 0 6.729,2.625 7.063,2.823 0.333,0.198 10 false 200 4.229,3.083 4.865,3.271 0.635,0.188 10 false Charge 6.49,3.083 7.146,3.302 0.656,0.219 10 false Discharge 4.948,3.198 6.25,3.427 1.302,0.229 10 false HV Battery Current 6.188,3.188 6.531,3.417 0.344,0.229 10 false (A)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ABF11 Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground The battery current sensor output voltage is excessively low.
(1 trip detection logic)
·

Battery voltage sensor

·

HV battery junction block assembly

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0ABF15 Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open The battery current sensor output voltage is excessively high.
(1 trip detection logic)
·

Battery voltage sensor

·

HV battery junction block assembly

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P1CBB12 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery Power source voltage of the battery current sensor is excessively high.
(1 trip detection logic)
·

Battery voltage sensor

·

HV battery junction block assembly

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P1CBB14 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open Power source voltage of the battery current sensor is excessively low.
(1 trip detection logic)
·

Battery voltage sensor

·

HV battery junction block assembly

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0ABF11 Hybrid Battery Current *1
P0ABF15
P1CBB12
P1CBB14

HINT:

*1: The value of "Hybrid Battery Current *1" will be approximately 0 A when the power switch is on (IG) (READY off).


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 10 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A311271E24
2.156,0.865 2.542,1.146 0.385,0.281 10 false 1 2.156,1.479 2.51,1.667 0.354,0.188 10 false 4 2.156,2.104 2.51,2.292 0.354,0.188 10 false 3 4.875,2.135 5.229,2.323 0.354,0.188 10 false 12 5.198,1.5 5.552,1.688 0.354,0.188 10 false IB0 4.875,0.854 5.229,1.042 0.354,0.188 10 false 6 5.167,0.854 5.521,1.042 0.354,0.188 10 false VIB 1.802,0.969 2.156,1.156 0.354,0.188 10 false VIB 4.927,1.5 5.281,1.688 0.354,0.188 10 false 5 1.813,1.594 2.167,1.781 0.354,0.188 10 false IB0 1.802,2.24 2.156,2.427 0.354,0.188 10 false GIB 5.167,2.135 5.521,2.323 0.354,0.188 10 false GIB 0.365,2.75 0.719,2.938 0.354,0.188 10 false z13 0.375,2.917 2.688,3.49 2.313,0.573 10 false HV Battery Junction Block Assembly (Battery Current Sensor) 5.01,2.76 5.365,2.948 0.354,0.188 10 false z12 5.01,2.927 6.75,3.229 1.74,0.302 10 false Battery Voltage Sensor

Refer to the wiring diagram for DTC P0AFC00.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AFC00

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery



·
A371653

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A371654C01
1.563,1.229 1.333,0.813 true 1.156,0.677 1.469,0.875 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
P0AFC00, P0AFC96 or P308A12 is not output. A
P0AFC00, P0AFC96 or P308A12 is also output. B


e.

Turn the power switch off.



A

2.CHECK BATTERY VOLTAGE SENSOR (IGCT VOLTAGE)

B

2.CHECK BATTERY VOLTAGE SENSOR (IGCT VOLTAGE)

OK

3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY VOLTAGE SENSOR POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery cover panel RH.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
A376407N06
1.792,0.948 2.167,1.188 0.375,0.24 1.854,0.969 2.135,1.167 0.281,0.198 10 true z13

Disconnect the battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


e.

Disconnect the battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



f.
A368052C05
2.198,2.094 2.625,2.354 0.427,0.26 2.063,3.552 2.49,3.813 0.427,0.26 1.198,1.781 1.583,2.281 true 1.771,4.031 2.365,4.208 true 0.844,2.458 1.49,2.396 true 0.865,2.094 1.5,2.271 true 0.844,4.208 1.469,4.052 true 0.854,3.583 1.448,3.76 true 0.229,0.073 0.677,0.552 0.448,0.479 10 false *a 0.344,3.01 0.917,3.542 0.573,0.531 10 false *b 2.313,2.125 2.76,2.604 0.448,0.479 10 false z12 2.167,3.594 2.615,4.073 0.448,0.479 10 false z13 0.969,1.688 1.542,2.219 0.573,0.531 10 false IB0 2.406,4.135 2.917,4.458 0.51,0.323 10 false IB0 0.615,2.385 1.188,2.917 0.573,0.531 10 false GIB 0.635,1.99 1.208,2.521 0.573,0.531 10 false VIB 0.583,4.146 1.156,4.531 0.573,0.385 10 false GIB 0.594,3.469 1.167,4 0.573,0.531 10 false VIB
*a Rear view of wire harness connector
(to Battery Voltage Sensor)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly (Battery Current Sensor))


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z12-5 (IB0) - z13-4 (IB0) Power switch off Below 1 Ω
z12-12 (GIB) - z13-3 (GIB) Power switch off Below 1 Ω
z12-6 (VIB) - z13-1 (VIB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
z12-5 (IB0) or z13-4 (IB0) - Body ground and other terminals Power switch off 10 kΩ or higher
z12-12 (GIB) or z13-3 (GIB) - Body ground and other terminals Power switch off 10 kΩ or higher
z12-6 (VIB) or z13-1 (VIB) - Body ground and other terminals Power switch off 10 kΩ or higher


HINT:

As the battery harness is not available as a supply part, if the harness cannot be repaired, replace the HV battery.



g.

Reconnect the battery voltage sensor connector.


h.

Install the No. 1 hybrid battery exhaust duct.


i.

Reconnect the battery current sensor connector to the HV battery junction block assembly.


j.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

4.CHECK BATTERY VOLTAGE SENSOR (VIB VOLTAGE)

NG

REPAIR HARNESS OR CONNECTOR (BATTERY CURRENT SENSOR)

4.CHECK BATTERY VOLTAGE SENSOR (VIB VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A368051C38
1.677,0.208 2.115,0.438 0.438,0.229 1.135,1.667 1.677,0.979 true 1.688,0.875 1.26,0.427 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 1.781,0.229 2.177,0.542 0.396,0.313 10 false z12 0.938,1.708 1.271,1.969 0.333,0.26 10 false GIB 0.958,0.344 1.292,0.604 0.333,0.26 10 false VIB
*a Component with harness connected
(Battery Voltage Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z12-6 (VIB) - z12-12 (GIB) Power switch on (IG) 4.6 to 5.4 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 hybrid battery exhaust duct.


Result:
Proceed to
OK
NG



OK

5.CHECK BATTERY VOLTAGE SENSOR (GIB - GND)

NG

9.CHECK BATTERY VOLTAGE SENSOR (VIB VOLTAGE)
5.CHECK BATTERY VOLTAGE SENSOR (GIB - GND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.

Disconnect the battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A379234C04
1.615,0.25 2.115,0.5 0.5,0.25 2.198,0.26 2.698,0.51 0.5,0.25 1.156,0.438 1.708,0.958 true 2.865,0.438 2.479,0.958 true 0.073,0.083 0.469,0.333 0.396,0.25 10 false *a 0.906,0.354 1.385,0.677 0.479,0.323 10 false GIB 2.323,0.271 2.802,0.594 0.479,0.323 10 false M41 1.771,0.271 2.25,0.594 0.479,0.323 10 false z12 2.906,0.354 3.354,0.76 0.448,0.406 10 false GND
*a Component without harness connected
(Battery Voltage Sensor)


Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
z12-12 (GIB) - M41-5 (GND) Power switch off Below 1 Ω



e.

Reconnect the battery voltage sensor connector.


f.

Install the No. 1 hybrid battery exhaust duct.


Result:
Proceed to
OK
NG



OK

6.CHECK BATTERY VOLTAGE SENSOR (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)

NG

6.CHECK BATTERY VOLTAGE SENSOR (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A368051C39
1.635,0.177 2.073,0.406 0.438,0.229 1.135,1.667 1.677,0.979 true 1.76,0.865 1.177,0.281 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 1.76,0.198 2.156,0.51 0.396,0.313 10 false z12 0.99,1.688 1.323,1.948 0.333,0.26 10 false GIB 0.823,0.177 1.156,0.438 0.333,0.26 10 false IB0
*a Component with harness connected
(Battery Voltage Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z12-5 (IB0) - z12-12 (GIB) Power switch on (IG) 2.46 to 2.54 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 hybrid battery exhaust duct.


Result:
Result Proceed to
OK A
NG(Voltage is outside the specified value and 0.4 V or more.) B
NG(Voltage is outside the specified value and less than 0.4 V.) C



A

B

7.CHECK BATTERY VOLTAGE SENSOR (VIB - IB0)

C

8.CHECK BATTERY VOLTAGE SENSOR (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)
7.CHECK BATTERY VOLTAGE SENSOR (VIB - IB0)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.

Disconnect the battery voltage sensor connectors.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A383475C03
1.604,0.25 2.104,0.5 0.5,0.25 1.708,0.885 1.354,0.479 true 2.417,0.479 1.771,0.885 true 0.177,0.104 0.656,0.49 0.479,0.385 10 false *a 1.75,0.271 2.229,0.656 0.479,0.385 10 false z12 1.115,0.396 1.594,0.781 0.479,0.385 10 false VIB 2.479,0.427 2.958,0.813 0.479,0.385 10 false IB0
*a Component without harness connected
(Battery Voltage Sensor)


Measure the resistance according to the value(s) in the tables below.

Tester Connection Condition
z12-6 (VIB) - z12-5 (IB0) Power switch off

Result:
Result Proceed to
Below 1 Ω A
Other than above B



e.

Reconnect the battery voltage sensor connectors.


f.

Install the No. 1 hybrid battery exhaust duct.



A

B

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

8.CHECK BATTERY VOLTAGE SENSOR (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery cover panel RH.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
A376407N06
1.792,0.948 2.167,1.188 0.375,0.24 1.854,0.969 2.135,1.167 0.281,0.198 10 true z13

Disconnect the battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Turn the power switch on (IG).


g.
A368051C39
1.635,0.177 2.073,0.406 0.438,0.229 1.135,1.667 1.677,0.979 true 1.76,0.865 1.177,0.281 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 1.76,0.198 2.156,0.51 0.396,0.313 10 false z12 0.99,1.688 1.323,1.948 0.333,0.26 10 false GIB 0.823,0.177 1.156,0.438 0.333,0.26 10 false IB0
*a Component with harness connected
(Battery Voltage Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z12-5 (IB0) - z12-12 (GIB) Power switch on (IG) 4.6 to 5.4 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Install the No. 1 hybrid battery exhaust duct.


k.

Reconnect the battery current sensor connector to the HV battery junction block assembly.


l.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NG

9.CHECK BATTERY VOLTAGE SENSOR (VIB VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery cover panel RH.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
A376407N06
1.792,0.948 2.167,1.188 0.375,0.24 1.854,0.969 2.135,1.167 0.281,0.198 10 true z13

Disconnect the battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Turn the power switch on (IG).


g.
A368051C38
1.677,0.208 2.115,0.438 0.438,0.229 1.135,1.667 1.677,0.979 true 1.688,0.875 1.26,0.427 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 1.781,0.229 2.177,0.542 0.396,0.313 10 false z12 0.938,1.708 1.271,1.969 0.333,0.26 10 false GIB 0.958,0.344 1.292,0.604 0.333,0.26 10 false VIB
*a Component with harness connected
(Battery Voltage Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z12-6(VIB) - z12-12 (GIB) Power switch on (IG) 4.6 to 5.4 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Install the No. 1 hybrid battery exhaust duct.


k.

Reconnect the battery current sensor connector to the HV battery junction block assembly.


l.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NG