Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV RELAY ASSEMBLY › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292499 HV RELAY ASSEMBLY A

HYBRID / BATTERY CONTROL  HV RELAY ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV battery junction block assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 6.INSTALL CONNECTOR COVER ASSEMBLY

Hide 8.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 9.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918A 10.REMOVE REAR DOOR SCUFF PLATE LH

Hide 76974F 11.REMOVE REAR UNDER SIDE COVER LH

Hide 67917A 12.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 76973F 13.REMOVE REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 76971G 14.REMOVE REAR UNDER COVER

Hide 71033 15.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G9230 16.REMOVE BATTERY COOLING BLOWER ASSEMBLY

Hide G92N4A 17.REMOVE NO. 1 HV BATTERY COVER PANEL RH

Hide 821H1 18.DISCONNECT HV FLOOR UNDER WIRE

Hide G92F1 20.REMOVE NO. 1 HYBRID BATTERY EXHAUST DUCT

Hide G920L 22.REMOVE UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY

Hide 23.REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A375911

Remove the bolt and disconnect the electric vehicle battery plug assembly.


b.
A378146

Disconnect the HV battery junction block assembly connector.

NOTICE:

Insulate the disconnected connectors with insulating tape.



c.

Disengage the clamp.


d.
A375912

Disengage the 2 claws and open the wiring harness protector.


e.
A375913

Disconnect the HV battery junction block assembly connector.

NOTICE:

Insulate the disconnected connectors with insulating tape.



f.
A375914C01
2.135,2.729 2.448,2.729 true 2.51,2.677 2.823,2.875 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and remove the wiring harness protector.


g.
A375915

Disconnect the HV battery junction block assembly connector.


h.
A375916

Remove the 4 nuts and HV battery junction block assembly from the No. 1 hybrid battery shield sub-assembly.

NOTICE:

If the HV battery junction block assembly has been struck or dropped, replace it with a new one.