Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292496 FRAME WIRE A

HYBRID / BATTERY CONTROL  FRAME WIRE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV floor under wire removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:
(Click here)
for Calibration:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 82121 3.DISCONNECT ENGINE WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.
A391963

Move each lock lever as shown in the illustration and disconnect the 2 inverter with converter assembly connectors.

NOTICE:
·

Do not touch the waterproof seal or terminals of the connector.

·

Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.

·

Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.

·

Insulate the disconnected terminals with insulating tape.




b.
A391980

Remove the bolt.


c.

Disengage the 2 clamps and disconnect the engine wire.


Hide 6.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY

Hide 8.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 9.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918A 10.REMOVE REAR DOOR SCUFF PLATE LH

Hide 76974F 11.REMOVE REAR UNDER SIDE COVER LH

Hide 67917A 12.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 76973F 13.REMOVE REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 76971G 14.REMOVE REAR UNDER COVER

Hide 71033 15.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G92N4A 16.REMOVE NO. 1 HV BATTERY COVER PANEL RH

Hide 821H1 17.DISCONNECT HV FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate the disconnected connectors with insulating tape.


a.
A375877C01
1.906,1.26 2.406,1.26 true 2.427,1.167 2.688,1.365 0.26,0.198 10 true *a
*a Shield Ground


Disconnect the 2 HV battery junction block assembly connectors.


b.

Disconnect the shield ground from the HV battery.


Hide 57627A 18.REMOVE REAR FLOOR SIDE MEMBER COVER RH

Hide 58165B 19.REMOVE FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.

Click hereEngine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>EXHAUST MANIFOLD>REMOVAL


Hide 51201 20.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 821H1 21.REMOVE HV FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate the disconnected connectors with insulating tape.


a.
A391981

Remove the 2 nuts.


b.

Remove the 3 clamps.

A391982

NOTICE:

If the clamps are removed forcibly, the stud bolts may be damaged.



c.
A391983

Disengage the grommet and pull out the HV floor under wire from the floor panel hole.


d.
A391984C01
0.083,0.177 0.354,0.396 0.271,0.219 12 true *A 0.844,1.188 1.042,1.385 0.198,0.198 10 true A 2.948,1.313 3.146,1.51 0.198,0.198 10 true B 0.104,2.573 0.375,2.792 0.271,0.219 12 true *B 2.875,3.792 3.073,3.99 0.198,0.198 10 true B 1.021,3.646 1.219,3.844 0.198,0.198 10 true A
*A for LHD
*B for RHD


Remove the clamp (A).


e.

Disengage the clamp (B) to remove the HV floor under wire.