Home › Drivetrain › P610 (HYBRID TRANSMISSION / TRANSAXLE) › OIL COOLER
RM32K0E _52 Drivetrain _059722 P610 HYBRID TRANSMISSION / TRANSAXLE _0292763 OIL COOLER A

P610 HYBRID TRANSMISSION / TRANSAXLE  OIL COOLER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL NO. 1 MOTOR COOLING HOSE

HINT:

Perform this procedure only when replacement of the motor cooling cooler is necessary.


a.
C353018C01
0,0 0,0 false
V100145

ATF Application Area


Coat a small amount of ATF as shown in the illustration.


b.
C345388C01
2.104,2.698 1.865,3.104 1.865,3.104 2.167,2.688 true 0.563,0.417 0.688,0.417 0.688,0.417 0.802,0.573 false 1.938,1.344 2.156,1.542 0.219,0.198 10 false *a 2.042,0.344 2.323,0.552 0.281,0.208 10 false *b 0.313,0.833 0.583,1.042 0.271,0.208 10 false *d 1.698,3.031 1.969,3.24 0.271,0.208 10 false *c 0.385,0.313 0.656,0.521 0.271,0.208 10 false *e
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark
*d Center of Paint Mark
*e 180°
V100145

Clip Location


Install the No. 1 motor cooling hose to the motor cooling cooler and slide the clip to secure it.

NOTICE:
·

Be careful not to deform the motor cooling cooler.

·

Make sure to align the paint mark on the No. 1 motor cooling hose with the paint mark on the motor cooling cooler.

·

Make sure that the claws of the clip are positioned within the area shown in the illustration.




Hide 2.INSTALL NO. 2 MOTOR COOLING HOSE

HINT:

Perform this procedure only when replacement of the motor cooling cooler is necessary.


a.
C353019C01
0,0 0,0 false
V100145

ATF Application Area


Coat a small amount of ATF as shown in the illustration.


b.
C345389C01
1.354,2.24 1.438,2.146 1.438,2.146 1.552,2.146 false 2.677,1.615 2.927,1.74 2.927,1.74 2.667,1.51 true 1.469,1.688 1.698,1.875 0.229,0.188 10 false *a 0.521,1.677 0.74,1.854 0.219,0.177 10 false *b 0.969,1.76 1.198,1.958 0.229,0.198 10 false *d 1.594,2.031 1.823,2.229 0.229,0.198 10 false *e 2.969,1.677 3.198,1.865 0.229,0.188 10 false *c
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark
*d Center of Paint Mark
*e 180°
V100145

Clip Location


Install the No. 2 motor cooling hose to the motor cooling cooler and slide the clip to secure it.

NOTICE:
·

Be careful not to deform the motor cooling cooler.

·

Make sure to align the paint mark on the No. 2 motor cooling hose with the paint mark on the motor cooling cooler.

·

Make sure that the claws of the clip are positioned within the area shown in the illustration.




Hide G125A 3.INSTALL MOTOR COOLING COOLER

a.
C365173N01
1.896,1.688 2.052,1.865 0.156,0.177 10 true 1 0.875,0.938 1.031,1.135 0.156,0.198 10 true 2 1.927,1.073 2.083,1.271 0.156,0.198 10 true 3

Temporarily install the motor cooling cooler to the hybrid vehicle transaxle assembly with the 3 bolts.


b.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


c.
C365174C01
0,0.417 0.521,0.427 false 2.354,0.969 2.615,0.969 true 2.354,0.979 2.615,1.052 true 2.948,1.125 3.26,1.281 0.313,0.156 10 false *a 2.177,0.865 2.49,1.021 0.313,0.156 10 false *b
*a 2 to 7 mm (0.0787 to 0.276 in.)
*b Paint Mark


Install the No. 2 motor cooling pipe to the No. 2 motor cooling hose and slide the clip to secure it.

NOTICE:

Make sure to align the paint mark on the No. 2 motor cooling pipe with the paint mark on the No. 2 motor cooling hose.



d.

Temporarily install the No. 2 motor cooling pipe to the hybrid vehicle transaxle assembly with the union bolt and a new gasket.


e.

Install the No. 1 oil cooler tube clamp to the hose bracket with the bolt.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


f.

Tighten the union bolt to install the No. 2 motor cooling pipe.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


g.
C343168C01
2.729,1 2.479,0.938 2.479,0.938 2.708,0.906 true 3.052,1.25 3.302,1.448 0.25,0.198 10 false *a 2.323,0.865 2.542,1.042 0.219,0.177 10 false *b
*a 2 to 7 mm (0.0787 to 0.276 in.)
*b Paint Mark


Connect the No. 1 motor cooling hose to the No. 1 motor cooling pipe and slide the clip to secure it.

NOTICE:

Make sure to align the paint mark on the No. 1 motor cooling pipe with the paint mark on the No. 1 motor cooling hose.



Hide G922F 4.CONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE

Hide G922H 5.CONNECT INLET HYBRID RADIATOR HOSE

Hide 17701 6.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 7.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 8.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide G9200 9.INSTALL INVERTER WITH CONVERTER ASSEMBLY

Hide 11.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 51444A 12.INSTALL REAR ENGINE UNDER COVER LH

Hide 51441 13.INSTALL NO. 1 ENGINE UNDER COVER