Home › Drivetrain › P610 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT LEVER POSITION SENSOR
RM32K0E _52 Drivetrain _059722 P610 HYBRID TRANSMISSION / TRANSAXLE _0292765 SHIFT LEVER POSITION SENSOR A

P610 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER POSITION SENSOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL SHIFT LEVER POSITION SENSOR SEAL

HINT:

Perform this procedure only when replacement of the shift lever position sensor seal is necessary.


a.

Coat the lip of a new shift lever position sensor seal with MP grease.


b.
C365185C01
2,1.094 2,0.844 false 1.427,1.104 1.74,1.26 0.313,0.156 10 false *a 1.865,1.125 2.323,1.323 0.458,0.198 10 false SST
*a Depth


Using SST and a hammer, install the shift lever position sensor seal to the hybrid vehicle transaxle assembly.

SST
09350-30020  (09350-07110)

Standard Depth:

4.05 to 5.40 mm (0.159 to 0.213 in.)


NOTICE:
·

Be sure to install the shift lever position sensor seal in the correct direction.

·

Do not install the shift lever position sensor seal at an angle.




Hide 89451A 2.INSTALL SHIFT LEVER POSITION SENSOR

a.

Temporarily install the shift lever position sensor to the hybrid vehicle transaxle assembly with the 2 bolts.

NOTICE:
·

Do not reuse the shift lever position sensor if it has been dropped or subjected to a severe impact.

·

Do not allow moisture to adhere to the connector terminal.




b.

Install the lock nut and lock plate to the shift lever position sensor.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


c.
C365186N01
2.688,0.042 2.844,0.24 0.156,0.198 10 false N 3.01,0.688 3.167,0.885 0.156,0.198 10 false P

Temporarily install the control shaft lever.


d.

Turn the control shaft lever clockwise until it stops, and then from that position turn it counterclockwise by 2 notches to set it to the N position.


e.

Remove the control shaft lever.


f.
C365187C01
0.833,2.781 0.833,1.448 true 1.083,2.531 1.083,1.448 true 0.75,2.802 1.063,2.958 0.313,0.156 10 false *a 1.01,2.573 1.323,2.729 0.313,0.156 10 false *b 1.927,2.344 2.24,2.5 0.313,0.156 10 false *c
*a Neutral Basic Line
*b Protrusion
*c Range of Play


Align the protrusion with the neutral basic line.

NOTICE:

The protrusion of the lock plate has a certain amount of play. Align the center point of the range of play with the neutral basic line.



g.
C365181N01
2.313,1.083 2.469,1.281 0.156,0.198 10 true 1 1.188,0.177 1.344,0.375 0.156,0.198 10 true 2

Tighten the 2 bolts in the order shown in the illustration.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


h.
C365179C02
1.75,1.417 1.75,1.083 true 1.677,1.427 1.885,1.625 0.208,0.198 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, bend down the tabs of the lock plate.


i.

Install the control shaft lever to the hybrid vehicle transaxle assembly with the nut and washer.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


j.

Connect the shift lever position sensor connector.


Hide 33820B 3.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


b.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Before connecting the transmission control cable assembly, check that the shift lever position sensor and shift lever are in neutral.



Hide 6.INSPECT SHIFT LEVER POSITION SENSOR POSITION

Hide 51444A 8.INSTALL REAR ENGINE UNDER COVER LH

Hide 51441 9.INSTALL NO. 1 ENGINE UNDER COVER