Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2019.09
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 2 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

Hybrid vehicle control ECU

·

Central gateway ECU (network gateway ECU)

·

Inverter with converter assembly

·

ECM

·

Brake booster with master cylinder assembly

·

No. 5 CAN junction connector

(for LHD)

·

No. 4 CAN junction connector

(for RHD)

·

No. 2 CAN junction connector



WIRING DIAGRAM

for LHD



C366138E03
1.344,0.719 1.958,0.917 0.615,0.198 10 false CANH 1.365,1.25 1.979,1.448 0.615,0.198 10 false CANL 1.844,0.625 2.01,0.823 0.167,0.198 10 false 1 1.875,1.135 2.042,1.333 0.167,0.198 10 false 7 0.427,1.594 1.042,1.792 0.615,0.198 10 false C65 0.438,1.76 2.604,2.01 2.167,0.25 10 false Inverter with Converter Assembly 2.656,0.625 2.99,0.823 0.333,0.198 10 false 10 2.656,1.167 2.99,1.365 0.333,0.198 10 false 21 4.01,0.625 4.344,0.823 0.333,0.198 10 false 8 4,1.167 4.333,1.365 0.333,0.198 10 false 19 4.99,0.635 5.323,0.833 0.333,0.198 10 false 18 4.969,1.167 5.302,1.365 0.333,0.198 10 false 17 5.26,0.635 5.875,0.833 0.615,0.198 10 false CA4H 5.26,1.167 5.875,1.365 0.615,0.198 10 false CA4L 5.927,1 6.542,1.198 0.615,0.198 10 false 120 Ω 5,1.625 5.615,1.823 0.615,0.198 10 false F74 5,1.792 6.99,2.208 1.99,0.417 10 false Central Gateway ECU (Network Gateway ECU) 4,2.76 4.333,2.958 0.333,0.198 10 false 7 3.99,3.302 4.323,3.5 0.333,0.198 10 false 18 2.646,3.302 2.979,3.5 0.333,0.198 10 false 20 2.708,2.76 3.042,2.958 0.333,0.198 10 false 9 1.833,2.75 2.167,2.948 0.333,0.198 10 false 25 1.844,3.302 2.177,3.5 0.333,0.198 10 false 24 1.365,2.865 1.979,3.063 0.615,0.198 10 false CA1H 1.385,3.396 2,3.594 0.615,0.198 10 false CA1L 0.5,3.74 1.115,3.938 0.615,0.198 10 false F3 0.5,3.906 2.417,4.156 1.917,0.25 10 false Hybrid Vehicle Control ECU 2.583,3.771 3.198,3.969 0.615,0.198 10 false F124 2.583,3.948 4.542,4.198 1.958,0.25 10 false No. 5 CAN Junction Connector 4,4.896 4.333,5.094 0.333,0.198 10 false 2 4,5.26 4.333,5.458 0.333,0.198 10 false 13 4,5.698 4.333,5.896 0.333,0.198 10 false 5 3.969,6.219 4.302,6.417 0.333,0.198 10 false 16 2.719,5.688 3.052,5.854 0.333,0.167 10 false 4 2.656,6.229 2.99,6.396 0.333,0.167 10 false 15 1.833,5.698 2.167,5.865 0.333,0.167 10 false 13 1.844,6.208 2.177,6.375 0.333,0.167 10 false 26 1.354,5.698 1.969,5.896 0.615,0.198 10 false CANH 1.375,6.229 1.99,6.427 0.615,0.198 10 false CANL 0.698,6.042 1.313,6.24 0.615,0.198 10 false 120 Ω 1.01,6.885 1.625,7.083 0.615,0.198 10 false ECM 1.021,6.698 1.635,6.896 0.615,0.198 10 false A38 2.677,6.708 3.292,6.906 0.615,0.198 10 false F113 2.677,6.875 4.594,7.125 1.917,0.25 10 false No. 2 CAN Junction Connector 4.99,5.698 5.323,5.896 0.333,0.198 10 false 30 4.979,6.219 5.313,6.417 0.333,0.198 10 false 29 5.25,5.771 5.865,5.969 0.615,0.198 10 false CA2H 5.25,6.344 5.865,6.542 0.615,0.198 10 false CA2L 5.094,6.698 5.708,6.896 0.615,0.198 10 false A39 5.083,6.875 6.781,7.323 1.698,0.448 10 false Brake Booster with Master Cylinder Assembly

for RHD



C366140E04
1.354,0.729 1.969,0.927 0.615,0.198 10 false CA2H 1.396,1.25 2.01,1.448 0.615,0.198 10 false CA2L 1.833,0.604 2.115,0.854 0.281,0.25 10 false 30 1.875,1.167 2.156,1.417 0.281,0.25 10 false 29 2.688,0.615 2.969,0.865 0.281,0.25 10 false 9 2.635,1.146 2.917,1.396 0.281,0.25 10 false 20 4,0.615 4.333,0.781 0.333,0.167 10 false 8 4.01,1.167 4.344,1.333 0.333,0.167 10 false 19 4,1.594 4.333,1.76 0.333,0.167 10 false 7 4,1.948 4.333,2.115 0.333,0.167 10 false 18 2.51,2.385 3.094,2.552 0.583,0.167 10 false F115 2.51,2.552 4.76,2.719 2.25,0.167 10 false No. 4 CAN Junction Connector 4.969,0.635 5.302,0.802 0.333,0.167 10 false 18 4.969,1.177 5.302,1.344 0.333,0.167 10 false 17 5.25,0.635 5.865,0.833 0.615,0.198 10 false CA4H 5.25,1.167 5.865,1.365 0.615,0.198 10 false CA4L 5.906,0.99 6.521,1.188 0.615,0.198 10 false 120 Ω 5.135,1.646 5.75,1.844 0.615,0.198 10 false F74 5.135,1.802 7.083,2.302 1.948,0.5 10 false Central Gateway ECU (Network Gateway ECU) 1.333,3.635 1.948,3.833 0.615,0.198 10 false CANH 1.365,4.167 1.979,4.365 0.615,0.198 10 false CANL 1.854,3.531 2.135,3.781 0.281,0.25 10 false 1 1.854,4.083 2.135,4.25 0.281,0.167 10 false 7 2.677,3.542 2.958,3.708 0.281,0.167 10 false 3 2.625,4.094 2.906,4.26 0.281,0.167 10 false 14 3.99,3.542 4.271,3.708 0.281,0.167 10 false 5 3.969,4.073 4.25,4.24 0.281,0.167 10 false 16 3.99,5.688 4.271,5.854 0.281,0.167 10 false 2 3.969,6.219 4.25,6.385 0.281,0.167 10 false 13 2.667,6.198 2.948,6.365 0.281,0.167 10 false 15 2.708,5.677 2.99,5.844 0.281,0.167 10 false 4 1.833,5.688 2.115,5.854 0.281,0.167 10 false 13 1.854,6.208 2.135,6.375 0.281,0.167 10 false 26 4.969,5.688 5.25,5.854 0.281,0.167 10 false 25 4.969,6.229 5.25,6.396 0.281,0.167 10 false 24 5.26,5.802 5.875,6 0.615,0.198 10 false CA1H 5.25,6.344 5.865,6.542 0.615,0.198 10 false CA1L 5.01,6.667 5.625,6.865 0.615,0.198 10 false F3 5.021,6.844 6.802,7.094 1.781,0.25 10 false Hybrid Vehicle Control ECU 2.583,6.677 3.198,6.875 0.615,0.198 10 false F113 2.583,6.844 4.5,7.094 1.917,0.25 10 false No. 2 CAN Junction Connector 1.01,6.698 1.625,6.896 0.615,0.198 10 false A38 1,6.854 1.5,7.021 0.5,0.167 10 false ECM 0.688,6.063 1.302,6.26 0.615,0.198 10 false 120 Ω 1.354,5.688 1.969,5.885 0.615,0.198 10 false CANH 1.375,6.208 1.99,6.406 0.615,0.198 10 false CANL 0.51,4.531 1.125,4.729 0.615,0.198 10 false C65 0.521,4.698 2.719,4.948 2.198,0.25 10 false Inverter with Converter Assembly 0.5,1.594 1.115,1.792 0.615,0.198 10 false A39 0.5,1.76 2.167,2.208 1.667,0.448 10 false Brake Booster with Master Cylinder Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on, turn the LDA main switch on and then drive the vehicle at a speed of 20 km/h (12 mph) or more for approximately 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR)

B

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366167C15
1.75,1.167 2.25,1.417 0.5,0.25 5.5,1 6,1.25 0.5,0.25 2.917,2.583 2.396,2.063 true 2.917,1.333 2.417,1.844 true 6.333,1.167 5.729,1.594 true 2.917,1 2.292,1.833 true 2.917,0.583 2.167,1.833 true 2.917,2.333 2.521,2.073 true 2.833,3.25 2.156,2.073 true 2.917,1.583 2.531,1.854 true 2.917,2.917 2.271,2.073 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 4.604,0.135 4.917,0.333 0.313,0.198 10 false *1 1.844,1.208 2.344,1.406 0.5,0.198 10 false F124 5.625,1.052 6.125,1.25 0.5,0.198 10 false F41 6.417,1.073 6.833,1.24 0.417,0.167 10 false CG 3,0.927 3.667,1.125 0.667,0.198 10 false CANH*c 2.99,1.25 3.656,1.448 0.667,0.198 10 false CANH*d 2.969,2.583 3.635,2.781 0.667,0.198 10 false CANL*d 2.969,2.927 3.635,3.125 0.667,0.198 10 false CANL*c 2.865,3.271 3.531,3.469 0.667,0.198 10 false CANL*b 2.979,0.49 3.646,0.688 0.667,0.198 10 false CANH*b 2.979,2.292 3.646,2.49 0.667,0.198 10 false CANL*e 3,1.51 3.667,1.708 0.667,0.198 10 false CANH*e
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to Hybrid Vehicle Control ECU
*e to Inverter with Converter Assembly - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F124-7 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 2 CAN junction connector
F124-18 (CANL) - F41-4 (CG)
F124-8 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F124-19 (CANL) - F41-4 (CG)
F124-9 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU
F124-20 (CANL) - F41-4 (CG)
F124-10 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inverter with converter assembly
F124-21 (CANL) - F41-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 2 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)

D

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C366167C16
1.75,1.167 2.25,1.417 0.5,0.25 5.5,1 6,1.25 0.5,0.25 6.333,1.167 5.729,1.615 true 2.677,1.24 2.281,1.833 true 2.667,2.5 2.281,2.073 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 4.604,0.135 4.917,0.333 0.313,0.198 10 false *1 1.844,1.208 2.344,1.406 0.5,0.198 10 false F124 5.625,1.052 6.125,1.25 0.5,0.198 10 false F41 6.406,1.073 6.823,1.24 0.417,0.167 10 false CG 2.698,2.542 3.365,2.74 0.667,0.198 10 false CANL*b 2.75,1.115 3.417,1.313 0.667,0.198 10 false CANH*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F124-8 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F124-19 (CANL) - F41-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C366167C17
1.75,1.167 2.25,1.417 0.5,0.25 5.5,1 6,1.25 0.5,0.25 1.469,1.844 1.083,1.583 true 1.167,2.75 1.719,2.063 true 5.729,1.604 6.396,1.188 true 1.844,1.854 1.083,1.083 true 1.719,1.854 1.083,1.333 true 1.49,2.063 1.167,2.406 true 1.5,2.917 1.875,2.063 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 4.604,0.135 4.917,0.333 0.313,0.198 10 false *1 1.844,1.208 2.344,1.406 0.5,0.198 10 false F113 5.625,1.052 6.125,1.25 0.5,0.198 10 false F41 6.469,1.094 6.854,1.281 0.385,0.188 10 false CG 0.615,2.354 1.281,2.552 0.667,0.198 10 false CANL*b 0.5,1.479 1.167,1.677 0.667,0.198 10 false CANH*b 0.635,2.708 1.302,2.906 0.667,0.198 10 false CANL*c 1.021,2.969 1.688,3.167 0.667,0.198 10 false CANL*d 0.521,1.219 1.188,1.417 0.667,0.198 10 false CANH*c 0.521,0.958 1.188,1.156 0.667,0.198 10 false CANH*d
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 5 CAN Junction Connector
*c to ECM *d to Brake Booster with Master Cylinder Assembly


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F113-2 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 5 CAN junction connector
F113-13 (CANL) - F41-4 (CG)
F113-4 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
F113-15 (CANL) - F41-4 (CG)
F113-5 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly
F113-16 (CANL) - F41-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to No. 5 CAN junction connector) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366167C18
1.75,1.167 2.25,1.417 0.5,0.25 5.5,1 6,1.25 0.5,0.25 2.667,2.833 2.156,2.083 true 2.833,0.917 2.167,1.833 true 6.333,1.167 5.729,1.615 true 2.917,1.25 2.292,1.833 true 2.917,1.583 2.417,1.854 true 2.917,2.583 2.292,2.073 true 2.917,2.333 2.406,2.063 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 4.604,0.135 4.917,0.333 0.313,0.198 10 false *1 1.844,1.208 2.344,1.406 0.5,0.198 10 false F115 5.625,1.052 6.125,1.25 0.5,0.198 10 false F41 6.427,1.063 6.844,1.229 0.417,0.167 10 false CG 3,1.135 3.667,1.333 0.667,0.198 10 false CANH*c 3,1.49 3.667,1.688 0.667,0.198 10 false CANH*d 2.99,2.323 3.656,2.521 0.667,0.198 10 false CANL*d 2.958,2.594 3.625,2.792 0.667,0.198 10 false CANL*c 2.698,2.885 3.365,3.083 0.667,0.198 10 false CANL*b 2.917,0.802 3.583,1 0.667,0.198 10 false CANH*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to Brake Booster with Master Cylinder Assembly


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F115-7 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 2 CAN junction connector
F115-18 (CANL) - F41-4 (CG)
F115-8 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F115-19 (CANL) - F41-4 (CG)
F115-9 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake Booster with Master Cylinder Assembly
F115-20 (CANL) - F41-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 2 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)

D

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C366167C19
1.75,1.167 2.25,1.417 0.5,0.25 5.5,1 6,1.25 0.5,0.25 6.417,1.167 5.729,1.615 true 2.281,2.073 2.833,2.5 true 2.833,1.333 2.292,1.844 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 4.604,0.135 4.917,0.333 0.313,0.198 10 false *1 1.844,1.208 2.344,1.406 0.5,0.198 10 false F115 5.625,1.052 6.125,1.25 0.5,0.198 10 false F41 6.5,1.063 6.917,1.229 0.417,0.167 10 false CG 2.917,2.427 3.583,2.625 0.667,0.198 10 false CANL*b 2.917,1.219 3.583,1.417 0.667,0.198 10 false CANH*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F115-8 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F115-19 (CANL) - F41-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C366167C20
1.75,1.167 2.25,1.417 0.5,0.25 5.5,1 6,1.25 0.5,0.25 1.479,1.844 1.083,1.667 true 1.083,2.25 1.479,2.052 true 5.719,1.615 6.417,1.167 true 1.167,2.5 1.625,2.052 true 1.333,2.667 1.75,2.063 true 1.5,2.917 1.875,2.063 true 1.594,1.854 1.083,1.417 true 1.729,1.844 1.083,1.083 true 1.854,1.833 1.167,0.833 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 4.604,0.135 4.917,0.333 0.313,0.198 10 false *1 1.844,1.208 2.344,1.406 0.5,0.198 10 false F113 5.625,1.052 6.125,1.25 0.5,0.198 10 false F41 6.5,1.052 6.885,1.24 0.385,0.188 10 false CG 0.542,2.177 1.208,2.375 0.667,0.198 10 false CANL*b 0.5,1.563 1.167,1.76 0.667,0.198 10 false CANH*b 0.51,1.281 1.177,1.479 0.667,0.198 10 false CANH*c 0.521,0.958 1.188,1.156 0.667,0.198 10 false CANH*d 0.615,0.688 1.281,0.885 0.667,0.198 10 false CANH*e 0.646,2.438 1.313,2.635 0.667,0.198 10 false CANL*c 0.813,2.688 1.479,2.885 0.667,0.198 10 false CANL*d 1.01,2.927 1.677,3.125 0.667,0.198 10 false CANL*e
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU
*c to Inverter with Converter Assembly *d to ECM
*e to No. 4 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F113-2 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU
F113-13 (CANL) - F41-4 (CG)
F113-3 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inverter with converter assembly
F113-14 (CANL) - F41-4 (CG)
F113-4 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
F113-15 (CANL) - F41-4 (CG)
F113-5 (CANH) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 4 CAN Junction Connector
F113-16 (CANL) - F41-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to No. 4 CAN junction connector) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
8.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C351161C81
5.083,0.292 5.49,0.563 0.406,0.271 1.635,0.156 2.042,0.406 0.406,0.25 1.969,1.396 2.25,0.75 true 1.823,1.406 1.583,0.75 true 5.292,1.156 5.667,0.75 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 3.938,0.063 4.25,0.26 0.313,0.198 10 false *1 5.177,0.354 5.49,0.552 0.313,0.198 10 false F41 5.75,0.635 6.271,0.854 0.521,0.219 10 false CG 1.719,0.198 2.031,0.396 0.313,0.198 10 false F74 2.323,0.646 2.792,0.854 0.469,0.208 10 false CA4L 1.188,0.646 1.656,0.854 0.469,0.208 10 false CA4H
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
F74-18 (CA4H) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-17 (CA4L) - F41-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to ground in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR