Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1210  Zero Point Calibration of Yaw Rate Sensor undone  C1336  Zero Point Calibration of Deceleration Sensor undone  


DESCRIPTION

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition using 2 circuits (GL1, GL2).

The skid control ECU (brake booster with master cylinder assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

HINT:

If there are malfunctions in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) will be stored.

If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.


These DTCs (C1210 and C1336) will also be stored when zero point calibration has not been completed.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1210 Zero Point Calibration of Yaw Rate Sensor Undone 1139 Yaw rate sensor zero point calibration is incomplete.
·

Yaw rate sensor (airbag sensor assembly) installed improperly

·

Yaw rate sensor (airbag sensor assembly)

·

Skid control ECU (brake booster with master cylinder assembly)


VSC DTC
C1336 Zero Point Calibration of Acceleration Sensor Undone 1138 Acceleration sensor zero point calibration is incomplete.
·

Acceleration sensor (airbag sensor assembly) installed improperly

·

Acceleration sensor (airbag sensor assembly)

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform yaw rate and acceleration sensor zero point calibration after clearing previously calibrated data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION



HINT:

When U0124 is output together with C1210 and/or C1336, inspect and repair trouble areas indicated by U0124 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION

NOTICE:

Make sure to perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization after performing "Reset Memory" as the data stored during linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization is cleared.


Chassis > ABS/VSC/TRC > Utility
Tester Display
Reset Memory
50005 105 138
Chassis > ABS/VSC/TRC > Utility
Tester Display
Test Mode
50005 105 166

Result:
Proceed to
NEXT



NEXT

2.PERFORM TEST MODE (SIGNAL CHECK)
2.PERFORM TEST MODE (SIGNAL CHECK)
a.

Using the GTS, perform a Test Mode (Signal Check) inspection sensor check and check that all Test Mode (Signal Check) inspection items change from incomplete to complete.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 4359
OK:

All Test Mode (Signal Check) inspection items change from incomplete to complete



Result:
Proceed to
OK
NG



OK

END

NG

3.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
3.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the power switch off.


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag sensor assembly) is not tilted.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)

NG

4.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Deceleration Sensor Acceleration sensor 1 Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Deceleration Sensor2 Acceleration sensor 2 Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Yaw Rate Sensor Yaw rate sensor 1 Min.: -128 degrees/s, Max.: 127 degrees/s Vehicle stationary: 0 degrees/s
Turning right: -128 to 0 degrees/s
Turning left: 0 to 127 degrees/s
-
Yaw Rate Sensor2 Yaw rate sensor 2 Min.: -128 degrees/s, Max.: 127 degrees/s Vehicle stationary: 0 degrees/s
Turning right: -128 to 0 degrees/s
Turning left: 0 to 127 degrees/s
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Deceleration Sensor
Deceleration Sensor2
Yaw Rate Sensor
Yaw Rate Sensor2
50003 105 14,15,24,25

b.

Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) output value is normal.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C