Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295698 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P10AA00  Clogged EGR Port Imbalance Bank1  


DESCRIPTION

Refer to DTC P030000.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P030000

Refer to DTC P04019C.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P04019C

Refer to DTC P21951D.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P21951D

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P10AA00 Clogged EGR Port Imbalance Bank1 The difference in the air fuel ratios between the cylinders exceeds the threshold when the EGR valve is open (2 trip detection logic).
·

Intake manifold

·

Fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Does not come on DTC stored SAE Code: P10AA

MONITOR DESCRIPTION

By comparing the air fuel ratio when EGR valve is open and closed, a clog in an EGR port can be detected. If the imbalance becomes larger when the EGR valve is open, the ECM will determine that the EGR port is clogged and store this DTC.

CONFIRMATION DRIVING PATTERN

A377955E03
0.063,2.24 1.115,2.625 1.052,0.385 10 false Power Switch on (IG) 0.75,1.958 1.125,2.219 0.375,0.26 10 false Idling 0.073,1.479 1.083,1.885 1.01,0.406 10 false 10 km/h [Engine stopped] 0.094,0.646 1.104,1.219 1.01,0.573 10 false 50 to 60 km/h [Engine running] 1.438,2.677 2.01,3.115 0.573,0.438 10 false Warming up 2.542,2.604 3.094,3.073 0.552,0.469 10 false 10 to 15 seconds 4.427,2.615 4.979,3.083 0.552,0.469 10 false 10 to 15 seconds 3.833,3.229 4.917,3.552 1.083,0.323 10 false 15 to 20 times 1.604,1.823 2.688,2.146 1.083,0.323 10 false [B] 2.646,0.979 3.729,1.302 1.083,0.323 10 false [D] 3.708,0.979 4.792,1.302 1.083,0.323 10 false [E] 1.177,2.104 2.26,2.427 1.083,0.323 10 false [A] 4.167,2.969 5.25,3.292 1.083,0.323 10 false [F] 6.656,2.75 6.948,3.063 0.292,0.313 10 false [G] 2.063,2.51 3.146,2.833 1.083,0.323 10 false [C] 6.802,2.531 7.156,2.771 0.354,0.24 10 false Time 0.229,0.115 1.24,0.417 1.01,0.302 10 false Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [B].

10.

Turn the power switch off [C].

11.

Turn the power switch on (READY).

12.

Start the engine by depressing the accelerator pedal approximately 40% and accelerating the vehicle from 10 km/h (6 mph) to a speed between 50 to 60 km/h (31 to 37 mph) in 10 to 15 seconds [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine does not start, further depress the accelerator pedal.


13.

Decelerate the vehicle to less than 10 km/h (6 mph) and allow the engine to stop [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

The vehicle can be decelerated by any method.


14.

Repeat steps [D] and [E] above 15 to 20 times [F].

15.

Enter the following menus: Powertrain / Engine / Trouble Codes [G].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

18.

Input the DTC: P10AA00.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.





WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

When any air fuel ratio imbalance is detected, the ECM will perform air fuel ratio feedback control to make the air fuel ratio close to the stoichiometric level. This may result in an air fuel ratio imbalance of normal cylinders and DTCs may be stored.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (DTC P10AA00)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P10AA00 is output A
DTC P10AA00 and other DTCs are output B


HINT:

If any DTCs other than DTC P10AA00 are output, troubleshoot those DTCs first.




A

2.REPLACE INTAKE MANIFOLD

B

2.REPLACE INTAKE MANIFOLD
a.

Replace the intake manifold.

Click hereEngine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>INTAKE MANIFOLD>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the intake system.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P10AA00 is output B




A

END

B

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)
5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up.

HINT:

The A/C switch and all accessories should be off and park (P) or neutral (N) should be selected.



f.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Data List / Misfire Count Cylinder #1 to #4.

HINT:

When the "Control the Injection Volume" Active Test is selected (injection volume is 0%), if a misfire count increases, proceed to step 7 (Check Intake System).


Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume
Data List Display
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
50004 372 7 148,149,150,151

g.

According to the display on the GTS, perform the Active Test with the engine idling.


h.

Check the misfire counts (Misfire Count Cylinder #1 to #4) while decreasing the injection volume in 5% increments.

Result:

The cylinder whose misfire count has not increased can be assumed to be running rich. Therefore, perform inspections while focusing on that cylinder.



Result:
Proceed to
NEXT



NEXT

6.CHECK FOR EXHAUST GAS LEAK
6.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

7.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE EXHAUST SYSTEM

7.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.INSPECT SPARK PLUG

NG

REPAIR OR REPLACE INTAKE SYSTEM

8.INSPECT SPARK PLUG
a.

Inspect the spark plug of the cylinder causing the imbalance.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

9.CHECK FOR SPARK (SPARK TEST)

NG

REPLACE SPARK PLUG

9.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

10.CHECK CYLINDER COMPRESSION PRESSURE
10.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
A395416C02
0.25,0.917 0.75,1.167 0.5,0.25 0.25,1.25 0.75,1.5 0.5,0.25 0.25,1.583 0.75,1.833 0.5,0.25 0.25,0.583 0.75,0.833 0.5,0.25 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 0.375,0.625 0.792,0.792 0.417,0.167 10 false C15 0.375,0.948 0.792,1.115 0.417,0.167 10 false C16 0.375,1.281 0.792,1.448 0.417,0.167 10 false C17 0.375,1.615 0.792,1.781 0.417,0.167 10 false C18
*a Front view of wire harness connector
(to Fuel Injector Assembly)


a.

Disconnect the fuel injector assembly connectors.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C15-1 - Body ground Power switch on (IG) 11 to 14 V
C16-1 - Body ground Power switch on (IG) 11 to 14 V
C17-1 - Body ground Power switch on (IG) 11 to 14 V
C18-1 - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

12.CHECK FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE

NG

12.CHECK FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE
a.

Check the fuel injector assembly (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>2ZR-FXE (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

13.CHECK FOR CAUSE OF FAILURE

NG

REPLACE FUEL INJECTOR ASSEMBLY

13.CHECK FOR CAUSE OF FAILURE
a.

If the cause of the problem has not been found even after performing the troubleshooting procedure, perform the inspection below.


b.

Check the intake valve for deposits.

HINT:

As the DTC may have been stored due to deposits on an intake valve, remove the cylinder head and check the intake valves.



Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
14.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output.



Result:
Proceed to
NEXT



NEXT

END