Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL INJECTOR › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _060063 2ZR-FXE FUEL _0294216 FUEL INJECTOR A

2ZR-FXE FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
·

Replacement of fuel injector assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 25601L 4.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY

Hide 12262 5.DISCONNECT NO. 2 VENTILATION HOSE

a.
A374331

Slide the clip and disconnect the No. 2 ventilation hose from the cylinder head cover sub-assembly.


Hide 82121 6.DISCONNECT ENGINE WIRE

a.
A374332

Disconnect the 4 fuel injector assembly connectors.


b.

Remove the bolt.


c.

Disengage the clamp to disconnect the engine wire.


Hide 23901 7.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A310731C02
1.031,0.375 1.344,0.531 0.313,0.156 10 false *a
*a Open
V100136

Pull


Open the cover of the fuel pipe clamp and remove the fuel pipe clamp from the fuel tube connector.


b.
A374334

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>2ZR-FXE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23807 8.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A374335

Remove the bolt to separate the clamp of the fuel delivery pipe sub-assembly from the cylinder head sub-assembly.


b.
A374337

Remove the 2 bolts and fuel delivery pipe sub-assembly with the 4 fuel injector assemblies.

NOTICE:

Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.



Hide 23807V 9.REMOVE NO. 1 DELIVERY PIPE SPACER

a.
A374558

Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.


Hide 23250 10.REMOVE FUEL INJECTOR ASSEMBLY

a.
A374339

Pull the 4 fuel injector assemblies out of the fuel delivery pipe sub-assembly.


b.
A374340

Remove the O-ring from each fuel injector assembly.


c.
A374341

Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the fuel injector assemblies with plastic bags to prevent damage and contamination.



d.
A374338

Remove the 4 injector vibration insulators from the cylinder head sub-assembly.