Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295698 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P013613  O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open  P013617  O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold  P01361C  O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Out of Range  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel ratio. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is high. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel ratio, the oxygen concentration in the exhaust gas is low. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric air fuel ratio.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the TWC is rich or lean, and adjusts the fuel injection duration accordingly. Thus, if the heated oxygen sensor is working improperly due to an internal malfunction, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A375466E01
1.083,2.917 1.333,2.917 true 2.563,2.333 3.146,2.333 true 2.667,2.75 3.083,2.917 true 2.677,1.781 3.198,1.781 true 2.656,1.417 3.313,1.25 3.313,1.25 2.802,1.469 true 2.958,1.24 3.281,0.792 true 1.396,2.823 2.167,3.021 0.771,0.198 10 false Cover 2,3.167 3.323,3.375 1.323,0.208 10 false Exhaust Gas 3.156,2.854 4.479,3.063 1.323,0.208 10 false Coating (Ceramic) 3.208,2.25 4.531,2.458 1.323,0.208 10 false Heater 3.25,1.688 4.552,2.198 1.302,0.51 10 false Solid Electrolyte (Zirconia Element) 3.396,1.177 4.698,1.688 1.302,0.51 10 false Platinum Electrolyte 3.333,0.677 4.635,1.188 1.302,0.51 10 false Housing 2.271,0.635 3.573,1.146 1.302,0.51 10 false Atmosphere 4.417,0.521 5.719,1.031 1.302,0.51 10 false Output Voltage 5.177,0.958 6.656,1.333 1.479,0.375 10 false Ideal Air Fuel Mixture 4.75,2.969 6.792,3.281 2.042,0.313 10 false Richer - Air Fuel Ratio - Leaner

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P013613 O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open Abnormal output voltage:

During active air fuel ratio control, the following conditions (a) and (b) are met for a certain amount of time (2 trip detection logic):

(a) Heated oxygen sensor voltage does not increase to 0.71 V or higher.

(b) Heated oxygen sensor voltage does not decrease to less than 0.21 V.


·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system

·

EGR valve assembly

·

Fuel pressure

·

Fuel system

·

PCV valve and hose

·

Intake system


Comes on DTC stored SAE Code: P0136
P013617 O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold Low voltage (open):

During active air fuel ratio control, the following conditions (a) and (b) are met for certain amount of time (2 trip detection logic):

(a) Heated oxygen sensor output voltage less than 0.21 V.

(b) Target air fuel ratio is rich.


·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system

·

EGR valve assembly


Comes on DTC stored SAE Code: P0137
P01361C O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Out of Range High voltage (short):

During active air fuel ratio control, the following conditions (a) and (b) are met for a certain amount of time (2 trip detection logic):

(a) Heated oxygen sensor output voltage is higher than 0.71 V.

(b) Target air fuel ratio is lean.


·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

EGR valve assembly

·

ECM


Comes on DTC stored SAE Code: P0138

MONITOR DESCRIPTION

Active Air fuel Ratio Control


The ECM usually performs air fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air fuel ratio. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and any malfunctions of the heated oxygen sensor (refer to the diagram below).

Active air fuel ratio control is performed for approximately 30 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Abnormal Heated Oxygen Sensor Output Voltage (DTC P013613)


While the ECM is performing active air fuel ratio control, the air fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the variation in output voltage is small. For example, when the heated oxygen sensor voltage does not increase to 0.71 V or higher during active air fuel ratio control, the ECM determines that the sensor output voltage is abnormal and stores DTC P013613.

A377134E01
2.75,2.354 2.833,2.604 2.833,2.604 3,2.604 false 2.833,2.104 3,1.771 3,1.771 3.167,1.771 false 0.115,0.156 5.156,0.521 5.042,0.365 10 false Heated Oxygen Sensor Circuit Malfunction (P013613: Abnormal Voltage) 0.146,1.365 5.188,1.729 5.042,0.365 10 false Active air fuel ratio control 0.125,2.531 5.167,2.896 5.042,0.365 10 false Heated oxygen sensor voltage 2.25,1.365 2.958,1.885 0.708,0.521 10 false OFF 2.135,2.135 2.844,2.656 0.708,0.521 10 false 0.71 V 2.135,2.917 2.844,3.438 0.708,0.521 10 false 0.21 V 3.083,2.531 3.917,2.781 0.833,0.25 10 false Abnormal 3.208,1.677 4.042,1.927 0.833,0.25 10 false Normal 4.219,0.781 6.042,1.24 1.823,0.458 10 false Approximately 30 seconds 4.698,1.281 6.521,1.74 1.823,0.458 10 false Operation


Open or Short in Heated Oxygen Sensor Circuit (DTC P013617 or P01361C)


During active air fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air fuel ratio to become rich or lean.

If the heated oxygen sensor has an open circuit, or the output voltage of the sensor noticeably decreases, the OSC will be an extremely high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the heated oxygen sensor output will not change.

While performing active air fuel ratio control, when the target air fuel ratio is rich and the heated oxygen sensor output voltage is less than 0.21 V (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P013617.

When the target air fuel ratio is lean and the output voltage is higher than 0.71 V (rich) during active air fuel ratio control, the ECM determines that the sensor output voltage is abnormally high and stores DTC P01361C.

HINT:

*: The TWC has the capability to store oxygen. The OSC and the emission purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P042000


A152992E84
5.823,3.792 6.021,4.031 false 4.292,2.052 4.448,1.729 false 4.448,1.729 4.594,1.729 false 5.302,2.406 5.448,1.719 false 5.448,1.719 5.625,1.719 false 5.677,3.021 5.844,2.563 false 5.844,2.563 6,2.563 false 5.729,6.583 5.969,6.104 false 5.969,6.104 6.104,6.104 false 0.063,0.052 4.406,0.26 4.344,0.208 10 false Heated Oxygen Sensor Circuit Low Voltage (P013617: Open) 0.281,1.219 1.281,1.563 1,0.344 10 false Active Air Fuel Ratio Control 0.281,3.208 1.271,3.563 0.99,0.354 10 false Heated Oxygen Sensor Voltage 0.281,2.083 1.656,2.281 1.375,0.198 10 false Target Air Fuel Ratio 1.979,2.031 2.927,2.396 0.948,0.365 10 false Stoichiometric Air Fuel Ratio 2.781,1.313 3.146,1.51 0.365,0.198 10 false Off 2.51,3.552 3,3.75 0.49,0.198 10 false 0.21 V 0.063,4.208 4.99,4.458 4.927,0.25 10 false Heated Oxygen Sensor Circuit High Voltage (P01361C: Short) 0.281,4.854 1.26,5.229 0.979,0.375 10 false Active Air Fuel Ratio Control 0.281,6.906 1.333,7.271 1.052,0.365 10 false Heated Oxygen Sensor Voltage 0.281,5.74 1.698,5.938 1.417,0.198 10 false Target Air Fuel Ratio 2.094,5.667 3.042,6.031 0.948,0.365 10 false Stoichiometric Air Fuel Ratio 2.74,4.938 3.094,5.135 0.354,0.198 10 false Off 3.958,0.396 5.635,0.667 1.677,0.271 10 false Approximately 30 seconds 4.521,1.281 5.281,1.479 0.76,0.198 10 false Operation 4.479,4.896 5.177,5.094 0.698,0.198 10 false Operation 4.708,5.708 5.104,5.906 0.396,0.198 10 false Lean 4.656,1.646 5.219,1.844 0.563,0.198 10 false Normal 6.146,6.01 6.833,6.208 0.688,0.198 10 false Abnormal 5.688,1.625 6.333,1.823 0.646,0.198 10 false Abnormal 6.063,4.063 6.802,4.26 0.74,0.198 10 false Abnormal 6.052,2.479 6.615,2.677 0.563,0.198 10 false Normal 4.781,2.417 5.146,2.615 0.365,0.198 10 false Rich 2.5,6.708 2.99,6.906 0.49,0.198 10 false 0.71 V 2.51,3.177 3,3.375 0.49,0.198 10 false 0.71 V 2.5,7.094 2.99,7.292 0.49,0.198 10 false 0.21 V


MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor (sensor 2)
Required Sensors/Components (Related) Crankshaft position sensor
Engine coolant temperature sensor
Mass air flow meter
Throttle position sensor
Air fuel ratio sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Heated Oxygen Sensor Voltage Check (Voltage Malfunction, High Voltage and Low Voltage)
Active air fuel ratio control Executing
Active air fuel ratio control begins when all of following conditions met: -
Auxiliary battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Idling Off
Engine speed Less than 4500 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 80%

TYPICAL MALFUNCTION THRESHOLDS

P013613: Heated Oxygen Sensor Voltage Check (Voltage Malfunction)
Either of following conditions is met 1 or 2
1. Both of following conditions are met -
(a) Commanded air fuel ratio 14.4 or less
(b) Heated oxygen sensor voltage 0.21 V or higher, and less than 0.71 V
2. Both of following conditions are met -
(c) Commanded air fuel ratio 14.8 or more
(d) Heated oxygen sensor voltage 0.21 V or higher, and less than 0.71 V

P013617: Heated Oxygen Sensor Voltage Check (Low Voltage)
Both of following conditions are met -
(a) Commanded air fuel ratio 14.4 or less
(b) Heated oxygen sensor voltage Less than 0.21 V

P01361C: Heated Oxygen Sensor Voltage Check (High Voltage)
Both of following conditions are met -
(a) Commanded air fuel ratio 14.8 or more
(b) Heated oxygen sensor voltage Higher than 0.71 V

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used for the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the heated oxygen sensor monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



A264212E41
1.74,2.427 1.563,2.802 1.563,2.802 1.417,2.802 false 4.021,0.719 4.25,0.875 0.229,0.156 10 false [C] 3.49,2.906 4.729,3.063 1.24,0.156 10 false 10 minutes or more 0.563,1.365 1.615,1.802 1.052,0.438 10 false 75 km/h [Engine running] 2.042,2.417 2.406,2.646 0.365,0.229 10 false [A] 0.479,0.479 1.594,0.979 1.115,0.5 10 false 120 km/h [Engine running] 1.25,2.229 1.698,2.49 0.448,0.26 10 false Idling 0.063,2.74 1.396,2.896 1.333,0.156 10 false Power Switch on (IG) 2.677,2.135 3.063,2.406 0.385,0.271 10 false [B] 2.333,2.917 3.135,3.073 0.802,0.156 10 false Warming up 5.01,3.313 5.24,3.469 0.229,0.156 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [B].

10.

With the engine running, drive the vehicle at 75 to 120 km/h (46 to 75 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P013613, P013617 or P01361C.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform steps [C] and [D] again.




WIRING DIAGRAM

A392137E04
0.875,0.417 1.031,0.615 0.156,0.198 10 false 3 2.219,0.844 2.375,1.042 0.156,0.198 10 false 5 2.208,0.396 2.365,0.594 0.156,0.198 10 false 4 0.875,0.844 1.031,1.042 0.156,0.198 10 false 6 1.302,1.219 1.938,1.427 0.635,0.208 10 false EFI-MAIN 0.865,1.896 2.313,2.104 1.448,0.208 10 false No. 1 Integration Relay 0.844,1.719 1.479,1.927 0.635,0.208 10 false 1B 0.396,2.354 1.844,2.563 1.448,0.208 10 false EFI-MAIN 0.385,3.135 1.833,3.344 1.448,0.208 10 false BATT-MAIN 0.542,3.958 1.99,4.167 1.448,0.208 10 false Auxiliary Battery 2.354,0.646 3.021,0.854 0.667,0.208 10 false EFI NO. 3 3.354,0.406 3.51,0.604 0.156,0.198 10 false 2 3.354,1.177 3.51,1.375 0.156,0.198 10 false 4 4.677,0.396 4.833,0.594 0.156,0.198 10 false 1 4.677,1.156 4.833,1.354 0.156,0.198 10 false 3 3.521,0.396 3.75,0.604 0.229,0.208 10 false +B 3.521,1.167 3.75,1.375 0.229,0.208 10 false E2 4.229,0.396 4.604,0.583 0.375,0.188 10 false HT1B 4.229,1.156 4.604,1.344 0.375,0.188 10 false OX1B 3.344,1.813 4.875,2.031 1.531,0.219 10 false Heated Oxygen Sensor 3.344,1.635 3.979,1.844 0.635,0.208 10 false C10 4.365,4.292 5.896,4.51 1.531,0.219 10 false *: Shielded 5.104,3.208 5.229,3.375 0.125,0.167 10 false * 5.594,0.323 5.792,0.51 0.198,0.188 10 false 56 5.552,0.5 5.844,0.677 0.292,0.177 10 false C63 5.552,1.281 5.844,1.458 0.292,0.177 10 false C63 5.563,2.74 5.854,2.917 0.292,0.177 10 false C63 5.563,3.938 5.854,4.115 0.292,0.177 10 false A38 5.604,1.104 5.802,1.292 0.198,0.188 10 false 99 5.573,2.563 5.844,2.74 0.271,0.177 10 false 131 5.615,3.771 5.885,3.948 0.271,0.177 10 false 46 5.927,0.396 6.344,0.583 0.417,0.188 10 false HT1B 5.906,1.167 6.323,1.354 0.417,0.188 10 false OX1B 5.906,2.646 6.323,2.833 0.417,0.188 10 false EX1B 5.917,3.844 6.333,4.031 0.417,0.188 10 false MREL 6.281,4.406 6.698,4.594 0.417,0.188 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Active Test "Control the Injection Volume for A/F Sensor". This Active Test can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following procedure describes how to perform the Active Test "Control the Injection Volume for A/F Sensor" using the GTS.


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

5.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

6.

Idle the engine for 5 minutes or more with park (P) selected.

7.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

8.

Perform the Active Test with the engine idling (change the fuel injection volume).

9.

Monitor the output voltage of the air fuel ratio sensor (A/F (O2) Sensor Voltage B1S1) and heated oxygen sensor (O2 Sensor Voltage B1S2) displayed on the GTS.


HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

Each sensor reacts in accordance with the increases and decreases in the fuel injection volume.



Standard:
GTS Display (Sensor) Injection Volume Status Voltage
A/F (O2) Sensor Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2 Sensor Voltage B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E20
5.792,3.625 7.115,3.896 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.531,1.594 1.979,1.781 0.448,0.188 8 false 12.5% 1.479,1.833 1.927,2.021 0.448,0.188 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 4.156,1.594 4.604,1.781 0.448,0.188 8 false 12.5% 4.115,1.833 4.563,2.021 0.448,0.188 8 false -12.5% 4.146,3.729 4.594,3.917 0.448,0.188 8 false 12.5% 4.104,3.917 4.552,4.104 0.448,0.188 8 false -12.5% 4.104,5.958 4.552,6.146 0.448,0.188 8 false -12.5% 4.104,8.021 4.552,8.208 0.448,0.188 8 false -12.5% 4.156,5.74 4.604,5.927 0.448,0.188 8 false 12.5% 4.156,7.813 4.604,8 0.448,0.188 8 false 12.5% 1.49,7.813 1.938,8 0.448,0.188 8 false 12.5% 1.49,5.75 1.938,5.938 0.448,0.188 8 false 12.5% 1.5,3.677 1.948,3.865 0.448,0.188 8 false 12.5% 1.448,3.896 1.896,4.083 0.448,0.188 8 false -12.5% 1.448,5.948 1.896,6.135 0.448,0.188 8 false -12.5% 1.438,8.021 1.885,8.208 0.448,0.188 8 false -12.5% 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.125,0.688 0.573,0.938 0.448,0.25 10 false Case 0.792,0.583 2.802,0.969 2.01,0.385 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.5,0.583 5.594,1.031 2.094,0.448 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.969,0.583 7.01,1 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4.031 7.125,4.469 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.635 7.125,5.073 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.917,5.604 6.969,5.979 1.052,0.375 10 false - Heated oxygen sensor 5.927,6.198 6.969,6.625 1.042,0.427 10 false - Heated oxygen sensor heater 5.927,6.792 6.969,7.229 1.042,0.438 10 false - Heated oxygen sensor circuit 5.927,7.469 6.813,7.875 0.885,0.406 10 false - Fuel injector assembly 5.917,8.083 7.073,8.417 1.156,0.333 10 false - Fuel pressure 5.917,8.531 7.01,9.313 1.094,0.781 10 false - Gas leak from exhaust system 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG

·

Performing the Active Test "Control the Injection Volume for A/F Sensor" allows the output voltage of the air fuel ratio sensor and heated oxygen sensor to be checked and graphed.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2; and then press the graph button on the Data List view.


NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (DTC P013613, P013617 OR P01361C)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P01361C is output A
DTC P013617 is output B
DTC P013613 is output C
DTC P013613, P013617 or P01361C and other DTCs are output D


HINT:

If any DTCs other than P013613, P013617 and P01361C are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (O2 SENSOR VOLTAGE B1S2)

B

14.CHECK FOR EXHAUST GAS LEAK

C

7.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

D

2.READ VALUE USING GTS (O2 SENSOR VOLTAGE B1S2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


f.

Idle the engine for 5 minutes or more with park (P) selected.


g.

Enter the following menus: Powertrain / Engine / Data List / O2 Sensor Voltage B1S2.

Powertrain > Engine > Data List
Tester Display
O2 Sensor Voltage B1S2
50003 372 218

h.

Read the heated oxygen sensor output voltage while idling.

Result:
Heated Oxygen Sensor Output Voltage Proceed to
1.0 V or higher A
Less than 1.0 V B




A

3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
A216381C02
1.542,2.021 1.083,1.708 false 1.531,2.313 1.094,2.615 false 1.969,2.313 2.313,2.615 false 0.365,0.292 0.542,0.469 0.177,0.177 10 *a 2.365,2.594 2.771,2.75 0.406,0.156 10 OX1B 0.896,2.573 1.115,2.729 0.219,0.156 10 E2 0.875,1.542 1.094,1.698 0.219,0.156 10 +B
*a Component without harness connected
(Heated Oxygen Sensor)


a.

Disconnect the C10 heated oxygen sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+B) - 4 (E2) Always 10 kΩ or higher
2 (+B) - 3 (OX1B) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Turn the power switch off and wait for 5 minutes or more.


b.

Disconnect the C63 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C63-56 (HT1B) - C63-99 (OX1B) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEATED OXYGEN SENSOR - ECM)

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


f.

Idle the engine for 5 minutes or more with park (P) selected.


g.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
A/F (O2) Sensor Voltage B1S1
O2 Sensor Voltage B1S2
50004 372 8 225,218

h.

Change the fuel injection volume using the GTS, and monitor the output voltage of the air fuel ratio sensor (A/F (O2) Sensor Voltage B1S1) and heated oxygen sensor (O2 Sensor Voltage B1S2) displayed on the GTS.

HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as A/F (O2) Sensor Voltage B1S1, and the heated oxygen sensor is displayed as O2 Sensor Voltage B1S2 on the GTS.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
GTS Display (Sensor) Voltage Variation Proceed to
A/F (O2) Sensor Voltage B1S1 (Air fuel ratio) Alternates between higher and less than 3.3 V OK
Remains at higher than 3.3 V NG
Remains at less than 3.3 V


HINT:

A normal the heated oxygen sensor voltage (O2 Sensor Voltage B1S2) reacts in accordance with increases and decreases in the fuel injection volume. When the air fuel ratio sensor voltage (A/F (O2) Sensor Voltage B1S1) remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A337301E01
4.479,1.479 4.813,1.313 4.813,1.313 4.979,1.313 false 4.5,2.302 4.667,2.635 4.667,2.635 4.833,2.635 false 3.5,1.708 3.563,1.854 3.563,1.854 3.729,1.854 false 0.375,2.479 1.448,2.677 1.073,0.198 10 false Voltage 5.854,0.708 6.979,0.958 1.125,0.25 10 false Injection Volume 2.188,0.333 3.313,0.583 1.125,0.25 10 false 12.5% 3.51,1.167 4.635,1.417 1.125,0.25 10 false -12.5% 3.76,1.781 4.25,2.135 0.49,0.354 10 true Normal 5.052,1.24 6.177,1.49 1.125,0.25 10 false Malfunction 0.938,1.885 2.063,2.135 1.125,0.25 10 false 3.3 V 1.052,2.896 2.177,3.146 1.125,0.25 10 false 1 V 1.052,3.396 2.177,3.646 1.125,0.25 10 false 0 V 5.667,2.927 7.104,3.365 1.438,0.438 10 false Heated Oxygen Sensor Output 5.74,1.708 7.063,2.135 1.323,0.427 10 false Air Fuel Ratio Sensor Output 4.906,2.552 6.031,2.802 1.125,0.25 10 false Malfunction



OK

6.INSPECT AIR FUEL RATIO SENSOR

NG

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
6.INSPECT AIR FUEL RATIO SENSOR
HINT:

This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current will indicate below 2.2 mA in this test.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


f.

With the engine running, drive the vehicle at 75 km/h (46 mph) or more for 10 minutes or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.



g.

Stop the vehicle.


h.

Enter the following menus: Powertrain / Engine / Data List / A/F (O2) Sensor Current B1S1.

Powertrain > Engine > Data List
Tester Display
A/F (O2) Sensor Current B1S1
50003 372 230

i.

With brake (B) selected and the engine running, drive the vehicle at 75 km/h (46 mph) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


A152792E94
1.354,2.51 2.635,2.698 1.281,0.188 10 false 10 minutes or more 2.969,2.51 4.177,2.698 1.208,0.188 10 false 5 seconds or more 4.271,2.51 5.469,2.698 1.198,0.188 10 false 5 seconds or more 5.563,2.51 6.74,2.698 1.177,0.188 10 false 5 seconds or more 0.156,0.073 1.458,0.292 1.302,0.219 12 false Driving Pattern: 0.031,1.313 1.021,1.771 0.99,0.458 10 false 75 km/h [Engine running] 0.552,2.198 1.521,2.448 0.969,0.25 10 false 0 km/h


j.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is performed.

Standard Current:

Less than 2.2 mA


HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the GTS.




Result:
Proceed to
OK
NG



OK

17.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
7.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


f.

Idle the engine for 5 minutes or more with park (P) selected.


g.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / O2 Sensor Voltage B1S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
O2 Sensor Voltage B1S2
50004 372 8 218

h.

Change the fuel injection volume using the GTS, and monitor the output voltage of the heated oxygen sensor (O2 Sensor Voltage B1S2) displayed on the GTS.

HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

The heated oxygen sensor has a maximum output delay of approximately 20 seconds.



Standard Voltage:

Fluctuates between 0.4 V or less, and 0.55 V or higher.



Result:
Proceed to
OK
NG



OK

8.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

14.CHECK FOR EXHAUST GAS LEAK
8.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


f.

Idle the engine for 5 minutes or more with park (P) selected.


g.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
A/F (O2) Sensor Voltage B1S1
O2 Sensor Voltage B1S2
50004 372 8 225,218

h.

Change the fuel injection volume using the GTS, and monitor the output voltage of the air fuel ratio sensor (A/F (O2) Sensor Voltage B1S1) and heated oxygen sensor (O2 Sensor Voltage B1S2) displayed on the GTS.

HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as A/F (O2) Sensor Voltage B1S1, and the heated oxygen sensor is displayed as O2 Sensor Voltage B1S2 on the GTS.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
GTS Display (Sensor) Voltage Variation Proceed to
A/F (O2) Sensor Voltage B1S1 (Air fuel ratio) Alternates between higher and less than 3.3 V OK
Remains at higher than 3.3 V NG
Remains at less than 3.3 V


HINT:

A normal the heated oxygen sensor voltage (O2 Sensor Voltage B1S2) reacts in accordance with increases and decreases in the fuel injection volume. When the air fuel ratio sensor voltage (A/F (O2) Sensor Voltage B1S1) remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A337301E01
4.479,1.479 4.813,1.313 4.813,1.313 4.979,1.313 false 4.5,2.302 4.667,2.635 4.667,2.635 4.833,2.635 false 3.5,1.708 3.563,1.854 3.563,1.854 3.729,1.854 false 0.375,2.479 1.448,2.677 1.073,0.198 10 false Voltage 5.854,0.708 6.979,0.958 1.125,0.25 10 false Injection Volume 2.188,0.333 3.313,0.583 1.125,0.25 10 false 12.5% 3.51,1.167 4.635,1.417 1.125,0.25 10 false -12.5% 3.76,1.781 4.25,2.135 0.49,0.354 10 true Normal 5.052,1.24 6.177,1.49 1.125,0.25 10 false Malfunction 0.938,1.885 2.063,2.135 1.125,0.25 10 false 3.3 V 1.052,2.896 2.177,3.146 1.125,0.25 10 false 1 V 1.052,3.396 2.177,3.646 1.125,0.25 10 false 0 V 5.667,2.927 7.104,3.365 1.438,0.438 10 false Heated Oxygen Sensor Output 5.74,1.708 7.063,2.135 1.323,0.427 10 false Air Fuel Ratio Sensor Output 4.906,2.552 6.031,2.802 1.125,0.25 10 false Malfunction



OK

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (FUEL INJECTOR ASSEMBLY, FUEL SYSTEM, INTAKE SYSTEM, ETC.)

NG

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
9.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

HINT:

The A/C switch and all accessories should be off.



f.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / Intake Manifold Absolute Pressure and Engine Independent.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Intake Manifold Absolute Pressure
Engine Independent
50004 372 25 385,428

g.

Confirm that the value of Data List item Engine Independent is "Operate" then check the value of Intake Manifold Absolute Pressure while performing the Active Test.

NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure changes in response to the EGR step position when the value of Engine Independent is "Operate".


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Intake Manifold Absolute Pressure
(Data List)
(EGR valve is fully closed) Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:
·

If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Perform the Active Test after charge control is complete ("Operate" is displayed).

·

While performing the Active Test, if the increase in the value of Intake Manifold Absolute Pressure is small, the EGR valve assembly may be malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of Intake Manifold Absolute Pressure may occur while performing the Active Test. However, the amount that the value of Intake Manifold Absolute Pressure increases will be smaller than normal.




Result:
Proceed to
OK
NG



OK

11.REPLACE AIR FUEL RATIO SENSOR

NG

10.INSPECT EGR VALVE ASSEMBLY
10.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

11.REPLACE AIR FUEL RATIO SENSOR

NG

11.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P013613 OR P01361C)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P013613 OR P01361C)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

c.

Input the DTC: P013613 or P01361C.


d.

Check that the DTC judgment result is NORMAL. If the DTC judgment result is INCOMPLETE, perform the confirmation drive pattern again but increase the vehicle speed.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P013613 or P01361C is output)
B




A

END

B

14.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

15.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

15.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

16.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the C10 heated oxygen sensor connector.


b.

Disconnect the C63 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C10-1 (HT1B) - C63-56 (HT1B) Always Below 1 Ω
C10-3 (OX1B) - C63-99 (OX1B) Always Below 1 Ω
C10-4 (E2) - C63-131 (EX1B) Always Below 1 Ω
C10-1 (HT1B) or C63-56 (HT1B) - Body ground and other terminals Always 10 kΩ or higher
C10-3 (OX1B) or C63-99 (OX1B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

HINT:

The A/C switch and all accessories should be off.



f.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / Intake Manifold Absolute Pressure and Engine Independent.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Intake Manifold Absolute Pressure
Engine Independent
50004 372 25 385,428

g.

Confirm that the value of Data List item Engine Independent is "Operate" then check the value of Intake Manifold Absolute Pressure while performing the Active Test.

NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure changes in response to the EGR step position when the value of Engine Independent is "Operate".


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Intake Manifold Absolute Pressure
(Data List)
(EGR valve is fully closed) Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:
·

If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Perform the Active Test after charge control is complete ("Operate" is displayed).

·

While performing the Active Test, if the increase in the value of Intake Manifold Absolute Pressure is small, the EGR valve assembly may be malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of Intake Manifold Absolute Pressure may occur while performing the Active Test. However, the amount that the value of Intake Manifold Absolute Pressure increases will be smaller than normal.




Result:
Proceed to
OK
NG



OK

19.REPLACE HEATED OXYGEN SENSOR

NG

18.INSPECT EGR VALVE ASSEMBLY
18.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

19.REPLACE HEATED OXYGEN SENSOR

NG

19.REPLACE HEATED OXYGEN SENSOR

Result:
Proceed to
NEXT



NEXT

20.CLEAR DTC
20.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

21.CHECK WHETHER DTC OUTPUT RECURS
21.CHECK WHETHER DTC OUTPUT RECURS
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

c.

Input the DTC: P013613, P013617 or P01361C.


d.

Check that the DTC judgment result is NORMAL. If the DTC judgment result is INCOMPLETE, perform the confirmation drive pattern again but increase the vehicle speed.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P013613, P013617 or P01361C is output)
B



HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

END

B