Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295698 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P044313  Evaporative Emission System Purge Control Valve "A" Circuit Open  


DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV so that the intake amount of evaporated fuel routed to the cylinders is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P044313 Evaporative Emission System Purge Control Valve "A" Circuit Open Both of the following conditions are met for 10 seconds or more (1 trip detection logic):
·

The purge VSV operation duty signal is 5 to 95%.

·

The target control value and actual control value do not match.


·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM


Comes on DTC stored SAE Code: P0443

CONFIRMATION DRIVING PATTERN

A179391E66
4.156,1.563 3.76,0.615 3.76,0.615 3.865,0.615 false 1.521,1.948 1.75,2.125 0.229,0.177 10 false [A] 2.844,1.948 3.073,2.125 0.229,0.177 10 false [B] 3.896,3.01 4.125,3.188 0.229,0.177 10 false [C] 4.573,1.333 4.802,1.51 0.229,0.177 10 false [D] 5.094,3.021 5.323,3.198 0.229,0.177 10 false [E] 0.51,2.073 0.885,2.26 0.375,0.188 10 false Idling 4.229,2.604 5.01,2.917 0.781,0.313 10 false 10 minutes or more 2.594,2.583 3.375,2.896 0.781,0.313 10 false 15 minutes or more 1.292,2.583 2.083,2.75 0.792,0.167 10 false Warming up 3.958,0.542 6.594,0.792 2.635,0.25 10 false Between 40 and 60 km/h [Engine running] 0.125,0.375 1.073,0.542 0.948,0.167 10 false Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C switch and all accessories should be off.


10.

Idle the engine for 15 minutes or more [B].

HINT:

Check the Data List item "EVAP (Purge) VSV". When the value of this item is between 5 and 95%, the judgment will be performed.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P044313.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform steps [D] and [E].



16.

With the engine running, drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


17.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

18.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



19.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

20.

Input the DTC: P044313.

21.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




WIRING DIAGRAM

A377769E04
4.115,1.49 5.49,1.688 1.375,0.198 10 false Purge VSV 4.094,1.333 5.469,1.531 1.375,0.198 10 false C12 1.281,2.271 2.813,2.521 1.531,0.25 10 false No. 1 Integration Relay 1.26,2.104 2.635,2.302 1.375,0.198 10 false 1B 0.594,3.219 2.125,3.469 1.531,0.25 10 false Auxiliary Battery 0.469,2.49 2,2.74 1.531,0.25 10 false BATT-MAIN 0.542,1.156 2.073,1.406 1.531,0.25 10 false EFI-MAIN 1.677,1.792 3.208,2.042 1.531,0.25 10 false EFI-MAIN 2.969,1.167 4.5,1.417 1.531,0.25 10 false EFI NO. 3 5.333,1.01 5.792,1.26 0.458,0.25 10 false C63 5.344,2.76 5.802,3.01 0.458,0.25 10 false A38 5.375,0.813 5.583,1.01 0.208,0.198 10 false 33 5.396,2.552 5.604,2.75 0.208,0.198 10 false 46 5.688,0.906 6.146,1.156 0.458,0.25 10 false PRG 5.677,2.656 6.135,2.906 0.458,0.25 10 false MREL 6.083,3.719 6.542,3.969 0.458,0.25 10 false ECM 5.063,0.896 5.271,1.094 0.208,0.198 10 false 1 3.802,0.896 4.01,1.094 0.208,0.198 10 false 2 1.208,1.417 1.417,1.615 0.208,0.198 10 false 6 2.688,0.896 2.896,1.094 0.208,0.198 10 false 4 1.198,0.896 1.406,1.094 0.208,0.198 10 false 3 2.667,1.406 2.875,1.604 0.208,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EVAP PURGE VSV)
A376497C01
0.969,1.802 1.281,2 0.313,0.198 10 false *a 2.594,1.833 2.906,2.031 0.313,0.198 10 false *b
*a VSV is on
*b VSV is off


a.

Disconnect the fuel vapor feed hose assembly (canister side) of the purge VSV.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

f.

Start the engine.


g.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EVAP Purge VSV.

Powertrain > Engine > Active Test
Tester Display
Activate the EVAP Purge VSV
50004 372 1

h.

When the purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction your finger.

OK:
GTS Operation Specified Condition
ON Purge VSV port applies suction to finger
OFF Purge VSV port applies no suction to finger


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV
a.

Inspect the purge VSV.

Click hereEngine / Hybrid System>2ZR-FXE (EMISSION CONTROL)>PURGE VALVE>INSPECTION

Result:
Proceed to
OK
NG




OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)
A376495C09
0.302,1.073 0.688,1.354 0.385,0.281 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 0.375,1.135 0.833,1.333 0.458,0.198 10 false C12
*a Front view of wire harness connector
(to Purge VSV)


a.

Disconnect the purge VSV connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C12-2 - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - PURGE VSV)

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the C12 purge VSV connector.


b.

Disconnect the C63 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C12-1 - C63-33 (PRG) Always Below 1 Ω
C12-1 or C63-33 (PRG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR