Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2016.10–2018.05
RM32K0E _54 Brake _060048 PARKING BRAKE _0296497 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13A1/12  Short in Power Supply Relay Circuit  


DESCRIPTION

The following DTCs are stored when a malfunction occurs in the parking brake ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A1/12 Short in Power Supply Relay Circuit Both of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off.

2.

Parking brake ECU assembly power source relay shorted for approximately 60 seconds.


·

Wire harness or connector

·

Electric parking brake switch (electric parking brake switch assembly)

·

Parking brake ECU assembly


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (IG) ○ -
Electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off - ○
Malfunction Status Parking brake ECU assembly power source relay is shorted ○ ○
Detection Time Approximately 60 seconds Approximately 60 seconds
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C322443E14
5.177,4.26 5.792,4.458 0.615,0.198 10 false REL2 5.188,3.604 5.802,3.802 0.615,0.198 10 false REL1 5.188,2.438 5.802,2.635 0.615,0.198 10 false LCK2 5.188,1.813 5.802,2.01 0.615,0.198 10 false LCK1 5.188,0.448 5.802,0.646 0.615,0.198 10 false IG 4.979,0.344 5.594,0.542 0.615,0.198 10 false 5 4.906,1.719 5.521,1.917 0.615,0.198 10 false 20 4.906,2.313 5.521,2.51 0.615,0.198 10 false 15 4.885,3.49 5.5,3.688 0.615,0.198 10 false 19 4.906,4.125 5.521,4.323 0.615,0.198 10 false 16 4.844,4.885 5.458,5.083 0.615,0.198 10 false M71 4.844,5.042 6.781,5.354 1.938,0.313 10 false Parking Brake ECU Assembly 3.615,1.656 4.229,1.854 0.615,0.198 10 false 6 3.604,2.281 4.406,2.552 0.802,0.271 10 false 3 3.604,3.458 4.333,3.698 0.729,0.24 10 false 5 3.604,4.094 4.271,4.333 0.667,0.24 10 false 4 1.354,0.635 2.427,0.854 1.073,0.219 10 false ECU-IG1 NO. 1 3.167,1.708 3.781,1.906 0.615,0.198 10 false LOK1 3.146,2.292 3.76,2.49 0.615,0.198 10 false LOK2 3.167,3.49 3.781,3.688 0.615,0.198 10 false RLS1 3.156,4.115 3.771,4.313 0.615,0.198 10 false RLS2 1.792,2.917 3.063,3.115 1.271,0.198 10 false Lock Switch (Pull) 1.771,4.74 3.26,4.979 1.49,0.24 10 false Release Switch (Push) 1.177,5.271 1.792,5.469 0.615,0.198 10 false GND1 0.896,5.25 1.573,5.656 0.677,0.406 10 false 2 1.063,5.938 1.677,6.135 0.615,0.198 10 false F67 1.073,6.104 3.479,6.51 2.406,0.406 10 false Electric Parking Brake Switch (Electric Parking Brake Switch Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the power switch is first turned on (IG).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - IG POWER SOURCE CIRCUIT)
a.
C319563C23
1.51,0.844 1.948,1.073 0.438,0.229 1.5,2.771 1.615,1.938 true 1.604,0.885 1.938,1.083 0.333,0.198 10 false M71 1.438,2.813 1.771,3.01 0.333,0.198 10 false IG 0.156,0.135 0.49,0.333 0.333,0.198 10 false *a
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)


Turn the power switch off.


b.

Disconnect the M71 parking brake ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M71-5 (IG) - Body ground Power switch off Below 2.5 V


Result:
Proceed to
OK
NG




OK

2.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Inspect the electric parking brake switch (electric parking brake switch assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the F67 electric parking brake switch (electric parking brake switch assembly) connector.


b.
C319563C24
1.5,0.875 1.938,1.115 0.438,0.24 1.385,2.635 1.625,2.135 true 2.5,2.625 2.292,2.135 true 2.021,2.635 1.813,2.146 true 2.802,2.083 2.521,2.083 true 1.594,0.906 1.938,1.083 0.344,0.177 10 false M71 1.229,2.677 1.615,2.917 0.385,0.24 10 false LCK2 1.896,2.677 2.281,2.917 0.385,0.24 10 false REL2 2.406,2.677 2.792,2.917 0.385,0.24 10 false REL1 2.854,2.021 3.24,2.26 0.385,0.24 10 false LCK1 0.167,0.135 0.51,0.313 0.344,0.177 10 false *a
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)


Disconnect the M71 parking brake ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M71-20 (LCK1) - Body ground Always 10 kΩ or higher
M71-15 (LCK2) - Body ground Always 10 kΩ or higher
M71-19 (REL1) - Body ground Always 10 kΩ or higher
M71-16 (REL2) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE PARKING BRAKE ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR