Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2016.10–2018.05
RM32K0E _54 Brake _060048 PARKING BRAKE _0296497 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13A3/31  Open or Short in Lock Switch Circuit  C13AB/33  Lock Switch Circuit  


DESCRIPTION

When the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side, a lock request signal is sent to the parking brake ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A3/31 Open or Short in Lock Switch Circuit All of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off.

2.

Terminal LCK1 voltage is less than 2.3 V or more than 4.35 V; or terminal LCK2 voltage is less than 1.5 V* or more than 9.4 V*

3.

Malfunction occurs for approximately 1 second.


HINT:

*: When auxiliary battery voltage is 12 V


·

Electric parking brake switch (electric parking brake switch assembly)

·

Wire harness or connector

·

Parking brake ECU assembly


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.
C13AB/33 Lock Switch Circuit Both of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off.

2.

ON/OFF judgment of lock switch 1 and lock switch 2 does not match for approximately 1 second.


·

Electric parking brake switch (electric parking brake switch assembly)

·

Wire harness or connector

·

Parking brake ECU assembly


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions: C13A3/31
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○
Malfunction Status Terminal LCK1 voltage is less than 2.3 V ○ - - -
Terminal LCK1 voltage is more than 4.35 V - ○ - -
Terminal LCK2 voltage is less than 1.5 V* - - ○ -
Terminal LCK2 voltage is more than 9.4 V* - - - ○
Detection Time Approximately 1 second Approximately 1 second Approximately 1 second Approximately 1 second
Number of Trips 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions: C13A3/31
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off ○ ○ ○ ○
Malfunction Status Terminal LCK1 voltage is less than 2.3 V ○ - - -
Terminal LCK1 voltage is more than 4.35 V - ○ - -
Terminal LCK2 voltage is less than 1.5 V* - - ○ -
Terminal LCK2 voltage is more than 9.4 V* - - - ○
Detection Time Approximately 1 second Approximately 1 second Approximately 1 second Approximately 1 second
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

*: When auxiliary battery voltage is 12 V



DTC Detection Conditions: C13AC/34
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (IG) ○ -
Electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off - ○
Malfunction Status ON/OFF judgment of lock switch 1 and lock switch 2 does not match ○ ○
Detection Time Approximately 1 second Approximately 1 second
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C322444E15
4.927,0.458 5.542,0.656 0.615,0.198 10 false LCK1 4.927,1.063 5.542,1.26 0.615,0.198 10 false LCK2 4.917,2.25 5.531,2.448 0.615,0.198 10 false REL1 4.927,2.875 5.542,3.073 0.615,0.198 10 false REL2 4.646,5.26 6.74,5.656 2.094,0.396 10 false Parking Brake ECU Assembly 4.656,5.094 5.271,5.292 0.615,0.198 10 false M71 4.646,0.354 5.26,0.552 0.615,0.198 10 false 20 4.646,0.958 5.26,1.156 0.615,0.198 10 false 15 4.635,2.146 5.25,2.344 0.615,0.198 10 false 19 4.635,2.771 5.25,2.969 0.615,0.198 10 false 16 3.344,0.354 3.958,0.552 0.615,0.198 10 false 6 3.344,0.938 4.167,1.146 0.823,0.208 10 false 3 3.344,2.135 3.958,2.333 0.615,0.198 10 false 5 3.333,2.76 3.948,2.958 0.615,0.198 10 false 4 2.865,0.354 3.479,0.552 0.615,0.198 10 false LOK1 2.865,0.948 3.479,1.146 0.615,0.198 10 false LOK2 2.875,2.135 3.49,2.333 0.615,0.198 10 false RLS1 2.875,2.771 3.49,2.969 0.615,0.198 10 false RLS2 1.583,1.583 3.01,1.781 1.427,0.198 10 false Lock Switch (Pull) 1.521,3.427 2.948,3.625 1.427,0.198 10 false Release Switch (Push) 0.906,3.917 2.333,4.115 1.427,0.198 10 false GND1 0.677,3.917 0.854,4.115 0.177,0.198 10 false 2 0.865,4.625 2.292,4.823 1.427,0.198 10 false F67 0.865,4.792 3.281,5.188 2.417,0.396 10 false Electric Parking Brake Switch (Electric Parking Brake Switch Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When the electric parking brake switch (electric parking brake switch assembly) is not fully pulled and held to the lock side for 1 second or more, only 1 of 2 internal contacts may contact causing a DTC to be stored. This is not a malfunction.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the power switch is first turned on (IG).



PROCEDURE

1.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Inspect the electric parking brake switch (electric parking brake switch assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the F67 electric parking brake switch (electric parking brake switch assembly) connector.


b.

Disconnect the M71 parking brake ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M71-20 (LCK1) - F67-6 (LOK1) Always Below 5 Ω
M71-15 (LCK2) - F67-3 (LOK2) Always Below 5 Ω
M71-20 (LCK1) or F67-6 (LOK1) - Body ground Always 10 kΩ or higher
M71-15 (LCK2) or F67-3 (LOK2) - Body ground Always 10 kΩ or higher
F67-2 (GND1) - Body ground Always Below 5 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

3.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Clear DTCs
50002 184

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Pull the electric parking brake switch (electric parking brake switch assembly) to the lock side.

HINT:

When the electric parking brake switch (electric parking brake switch assembly) is not fully pulled and held to the lock side for 1 second or more, only 1 of 2 internal contacts may contact causing a DTC to be stored. This is not a malfunction.



e.

Check for DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE PARKING BRAKE ECU ASSEMBLY

B