Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2016.10–2018.05
RM32K0E _54 Brake _060048 PARKING BRAKE _0296497 ELECTRIC PARKING BRAKE SYSTEM J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  Electric Parking Brake does not Operate  


WIRING DIAGRAM

C367786E02
0.479,0.719 1.479,0.896 1,0.177 10 false ECU-IG1 NO. 1 0.521,1.302 1.521,1.479 1,0.177 10 false ECU-B NO. 2 2.792,0.438 2.906,0.615 0.115,0.177 10 false 5 2.823,1.531 3.135,1.729 0.313,0.198 10 false M71 2.792,1.042 2.906,1.219 0.115,0.177 10 false 3 2.823,1.688 4.698,1.917 1.875,0.229 10 false Parking Brake ECU Assembly 2.969,0.521 3.281,0.719 0.313,0.198 10 false IG 2.969,1.125 3.406,1.313 0.438,0.188 10 false BECU 5.302,1.313 7.135,1.521 1.833,0.208 10 false Combination Meter Assembly 0.917,2.417 2.75,2.625 1.833,0.208 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the power switch is first turned on (IG).



HINT:

Even if the electric parking brake is operating normally, the parking brake indicator light (red) on the combination meter may be malfunctioning.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.VEHICLE OPERATION CHECK

B

2.VEHICLE OPERATION CHECK
a.

When the vehicle's tires are lifted off the ground and the GTS is used to operate the electric parking brake, check the condition of the rear tires.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>ON-VEHICLE INSPECTION


Result:
Result Proceed to
Lock and release operation is normal and parking brake indicator light turns off or blinks (red) A
Lock and release operation is malfunctioning and parking brake indicator light illuminates (red) or turns off according to switch operation B
Lock and release operation is malfunctioning and parking brake indicator light turns off or blinks (red) C



A

3.PERFORM ACTIVE TEST USING GTS (PARKING BARKE LIGHT)

B

INSPECT REAR BRAKE

C

5.CHECK HARNESS AND CONNECTOR (BECU CIRCUIT)
3.PERFORM ACTIVE TEST USING GTS (PARKING BARKE LIGHT)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Active Test.


f.

Perform the Active Test according to the display on the GTS.

Chassis > Electric Parking Brake > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PKB Light Parking brake indicator light (red) ON or OFF
·

Vehicle stopped

·

Power switch on (IG)

·

Parking brake released


Chassis > Electric Parking Brake > Active Test
Tester Display
PKB Light
50004 184 29

g.

Select the Data List on the GTS.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Parking Brake Light Parking brake indicator light (red) output signal OFF, Light or Blink OFF: Parking brake indicator light (red) turns off
Light: Parking brake indicator light (red) illuminates
Blink: Parking brake indicator light (red) flashes
-
Chassis > Electric Parking Brake > Data List
Tester Display
Parking Brake Light
50003 184 45

h.

Check the operating condition of the parking brake indicator light (red) when operating it using the GTS.

Result:
Result Proceed to
Parking brake indicator light (red) in the Data List does not change using the Active Test. A
Parking brake indicator light (red) in the Data List turns ON/OFF using the Active Test. B




A

REPLACE PARKING BRAKE ECU ASSEMBLY

B

4.INSPECT COMBINATION METER ASSEMBLY
4.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Park
50004 122 69

b.

Check the combination meter assembly.

OK:

Parking brake indicator light (red) turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ECU ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (BECU CIRCUIT)
a.

Turn the power switch off.


b.

Disconnect the M71 parking brake ECU assembly connector.


c.
C319563C25
1.5,0.875 1.938,1.115 0.438,0.24 1.188,2.646 1.292,1.948 true 1.583,0.896 1.927,1.073 0.344,0.177 10 false M71 1.042,2.688 1.531,2.906 0.49,0.219 10 false BECU 0.167,0.135 0.51,0.313 0.344,0.177 10 false *a
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M71-3 (BECU) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - PARKING BRAKE ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - PARKING BRAKE ECU ASSEMBLY)
a.

Turn the power switch off.


b.

Disconnect the M71 parking brake ECU assembly connector.


c.
C319563C26
1.5,0.875 1.938,1.115 0.438,0.24 1.854,2.656 1.635,1.938 true 1.594,0.906 1.938,1.083 0.344,0.177 10 false M71 1.833,2.708 2.219,2.948 0.385,0.24 10 false IG 0.167,0.135 0.51,0.313 0.344,0.177 10 false *a
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M71-5 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR