Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2016.10–2018.05
RM32K0E _54 Brake _060048 PARKING BRAKE _0296497 ELECTRIC PARKING BRAKE SYSTEM J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  Electric Parking Brake System AUTO Function Circuit  


DESCRIPTION

The parking brake ECU assembly receives shift position information from the hybrid vehicle control ECU via CAN communication, and wheel speed signal and stop light switch signals from the skid control ECU assembly.

In addition, front seat inner belt information and driver seat door courtesy switch information is received from the main body ECU (multiplex network body ECU).

The electric parking brake system AUTO function (shift-linked function) automatically releases the parking brake when the following conditions are met: 1) Power switch is on (IG), 2) brake pedal is depressed, and 3) shift lever is moved out of P. When the shift lever is moved to P with these conditions met, the function automatically locks the parking brake.

The electric parking brake system AUTO (shift-linked function) automatically engages the parking brake when the shift lever is moved to P and disengages the parking brake when the shift lever is moved out of P when the power switch is on (IG) and the brake pedal is depressed.

WIRING DIAGRAM

C367784E01
0.625,4.094 1.073,4.271 0.448,0.177 10 false GND1 2.563,0.563 3.01,0.74 0.448,0.177 10 false LOK1 2.573,1.146 3.021,1.323 0.448,0.177 10 false LOK2 2.583,2.333 3.031,2.51 0.448,0.177 10 false RLS1 2.583,2.969 3.031,3.146 0.448,0.177 10 false RLS2 0.594,4.76 2.969,5.135 2.375,0.375 10 false Electric Parking Brake Switch (Electric Parking Brake Switch Assembly) 1.042,5.385 3.063,5.573 2.021,0.188 10 false : CAN Communication Line 3.906,0.646 4.354,0.823 0.448,0.177 10 false LCK1 3.917,1.229 4.365,1.406 0.448,0.177 10 false LCK2 3.906,2.406 4.354,2.583 0.448,0.177 10 false REL1 3.906,3.073 4.354,3.25 0.448,0.177 10 false REL2 5.219,1.125 7.063,1.354 1.844,0.229 10 false Combination Meter Assembly 5.229,2.365 7.073,2.594 1.844,0.229 10 false Hybrid Vehicle Control ECU 5.313,3.563 6.969,3.938 1.656,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 5.083,4.896 7.125,5.292 2.042,0.396 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.542,4.792 4.76,5.146 1.219,0.354 10 false Parking Brake ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the power switch is first turned on (IG).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING GTS (AUTO MODE)

B

2.READ VALUE USING GTS (AUTO MODE)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto Mode AUTO (shift-linked) mode permission status OFF or ON OFF: Manual mode
ON: AUTO (shift-linked) mode
-
Chassis > Electric Parking Brake > Data List
Tester Display
Auto Mode
50003 184 628

g.

When switching the mode, check that the Data List display turns on and off.

Result:
Result Proceed to
The Data List display does not turn on and off according to mode switching A
The Data List display turns on and off according to mode switching B




A

3.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

B

5.READ VALUE USING GTS (SHIFT POSITION)
3.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Inspect the electric parking brake switch (electric parking brake switch assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the F67 electric parking brake switch (electric parking brake switch assembly) connector.


b.

Disconnect the M71 parking brake ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M71-20 (LCK1) - F67-6 (LOK1) Always Below 5 Ω
M71-15 (LCK2) - F67-3 (LOK2) Always Below 5 Ω
M71-20 (LCK1) or F67-6 (LOK1) - Body ground Always 10 kΩ or higher
M71-15 (LCK2) or F67-3 (LOK2) - Body ground Always 10 kΩ or higher
M71-19 (REL1) - F67-5 (RLS1) Always Below 5 Ω
M71-16 (REL2) - F67-4 (RLS2) Always Below 5 Ω
M71-19 (REL1) or F67-5 (RLS1) - Body ground Always 10 kΩ or higher
M71-16 (REL2) or F67-4 (RLS2) - Body ground Always 10 kΩ or higher
F67-2 (GND1) - Body ground Always Below 5 Ω



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (SHIFT POSITION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (SHIFT POSITION)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position Position of shift lever P, N, R, D or Unknown P: Shift lever in P
N: Shift lever in N
R: Shift lever in R
D: Shift lever in D or B
When not normal, shift position signal system may be malfunctioning
Chassis > Electric Parking Brake > Data List
Tester Display
Shift Position
50003 184 600
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (STOP LIGHT SWITCH)

NG

6.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch Stop light switch assembly input signal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Chassis > Electric Parking Brake > Data List
Tester Display
Stop Light Switch
50003 184 597
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (DOOR COURTESY SW)

NG

7.READ VALUE USING GTS (DOOR COURTESY SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical > Main Body > Data List


f.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly RH (for RHD) ON or OFF ON: Front door RH open
OFF: Front door RH closed
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part.
FL Door Courtesy SW Front door courtesy light switch assembly LH (for LHD) ON or OFF ON: Front door LH open
OFF: Front door LH closed
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part.
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 197,199
OK:

The Data List item changes in accordance with the opening and closing of the driver door.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (D SEAT BUCKLE SW)

NG

8.READ VALUE USING GTS (D SEAT BUCKLE SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical > Main Body > Data List


f.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Seat Buckle SW Driver seat belt buckle switch OFF or ON ON: Driver seat belt unfastened
OFF: Driver seat belt fastened
-
Body Electrical > Main Body > Data List
Tester Display
D Seat Buckle SW
50003 123 14
OK:

Unset or Set is displayed on the GTS according to the driver seat belt condition.



Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ECU ASSEMBLY

NG