Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2016.10–2018.05
RM32K0E _54 Brake _060048 PARKING BRAKE _0296497 ELECTRIC PARKING BRAKE SYSTEM J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  Electric Parking Brake AUTO Indicator Light Circuit  


DESCRIPTION

Pulling the electric parking brake switch to the lock side for 5 seconds or more changes the AUTO function (shift-linked function) to ON, and an AUTO Mode ON message is displayed on the multi-information display in the combination meter.

Pressing the electric parking brake switch to the release side for 5 seconds or more changes the AUTO function (shift-linked function) to OFF, and an AUTO Mode OFF message is displayed on the multi-information display in the combination meter.

WIRING DIAGRAM

C367784E01
0.625,4.094 1.073,4.271 0.448,0.177 10 false GND1 2.563,0.563 3.01,0.74 0.448,0.177 10 false LOK1 2.573,1.146 3.021,1.323 0.448,0.177 10 false LOK2 2.583,2.333 3.031,2.51 0.448,0.177 10 false RLS1 2.583,2.969 3.031,3.146 0.448,0.177 10 false RLS2 0.594,4.76 2.969,5.135 2.375,0.375 10 false Electric Parking Brake Switch (Electric Parking Brake Switch Assembly) 1.042,5.385 3.063,5.573 2.021,0.188 10 false : CAN Communication Line 3.906,0.646 4.354,0.823 0.448,0.177 10 false LCK1 3.917,1.229 4.365,1.406 0.448,0.177 10 false LCK2 3.906,2.406 4.354,2.583 0.448,0.177 10 false REL1 3.906,3.073 4.354,3.25 0.448,0.177 10 false REL2 5.219,1.125 7.063,1.354 1.844,0.229 10 false Combination Meter Assembly 5.229,2.365 7.073,2.594 1.844,0.229 10 false Hybrid Vehicle Control ECU 5.313,3.563 6.969,3.938 1.656,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 5.083,4.896 7.125,5.292 2.042,0.396 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.542,4.792 4.76,5.146 1.219,0.354 10 false Parking Brake ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (electric parking brake switch assembly), as the parking brake indicator light (red) blinks when the power switch is first turned on (IG).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING GTS (AUTO MODE)

B

2.READ VALUE USING GTS (AUTO MODE)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and the GTS on.


d.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


e.

Check the values by referring to the table below.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto Mode AUTO (shift-linked) mode permission status OFF or ON OFF: Manual mode
ON: AUTO (shift-linked) mode
-
Chassis > Electric Parking Brake > Data List
Tester Display
Auto Mode
50003 184 628

f.

When switching the mode, check that the Data List display turns on and off.


Result:
Result Proceed to
AUTO indicator light does not illuminate and turn off according to turning Active Test on and off A
AUTO indicator light illuminates and turns off according to turning Active Test on and off B



A

3.CHECK DTC

B

6.PERFORM ACTIVE TEST USING GTS (AUTO MODE)
3.CHECK DTC
a.

Check for DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Result Proceed to
DTC is not output A
DTC is output B



A

4.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

B

4.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Inspect the electric parking brake switch (electric parking brake switch assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the F67 electric parking brake switch (electric parking brake switch assembly) connector.


b.

Disconnect the M71 parking brake ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M71-20 (LCK1) - F67-6 (LOK1) Always Below 5 Ω
M71-15 (LCK2) - F67-3 (LOK2) Always Below 5 Ω
M71-20 (LCK1) or F67-6 (LOK1) - Body ground Always 10 kΩ or higher
M71-15 (LCK2) or F67-3 (LOK2) - Body ground Always 10 kΩ or higher
M71-19 (REL1) - F67-5 (RLS1) Always Below 5 Ω
M71-16 (REL2) - F67-4 (RLS2) Always Below 5 Ω
M71-19 (REL1) or F67-5 (RLS1) - Body ground Always 10 kΩ or higher
M71-16 (REL2) or F67-4 (RLS2) - Body ground Always 10 kΩ or higher
F67-2 (GND1) - Body ground Always Below 5 Ω



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (AUTO MODE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.PERFORM ACTIVE TEST USING GTS (AUTO MODE)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Active Test.


f.

Perform the Active Test according to the display on the GTS.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > Electric Parking Brake > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Auto Mode AUTO (shift-linked) mode ON or OFF
·

Vehicle stopped

·

Ignition switch ON


Chassis > Electric Parking Brake > Active Test
Tester Display
Auto Mode
50004 184 27

g.

Select the Data List on the GTS.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto Mode AUTO (shift-linked) mode permission display ON or OFF ON: AUTO (shift-linked) mode
OFF: Manual mode
-
Chassis > Electric Parking Brake > Data List
Tester Display
Auto Mode
50003 184 64

h.

Perform the Auto Mode Active Test, and check that the Data List display changes.


Result:
Result Proceed to
Check the operating condition of the "Auto Mode" when operating it using the GTS. A
"Auto Mode" in the Data List turns ON/OFF using the Active Test. B



A

REPLACE PARKING BRAKE ECU ASSEMBLY

B

7.INSPECT COMBINATION METER ASSEMBLY
7.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7

b.

Check the multi-information display the combination meter assembly turn ON or OFF in accordance with the GTS operation.

OK:

The message in the multi-information display appears and disappears in accordance with the Active Test operation.



Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ECU ASSEMBLY

NG