Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT › 2016.10–2019.09
RM32K0E _52 Drivetrain _061337 AXLE AND DIFFERENTIAL _0299679 REAR AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle hub bolt removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point
·

Lane departure alert system (w/ Steering Control)

·

Simple intelligent parking assist system*1

·

Toyota parking assist sensor system*1

·

Pre-collision system


(Click here)
Initialize back door lock Power door lock control system (Click here)


NOTICE:
·

When removing or installing the rear disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISABLE BRAKE CONTROL

Hide 3.REMOVE REAR WHEEL

Hide 4.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

a.
C365603

Disconnect the No. 2 parking brake wire assembly connector.


b.

Remove the bolt and separate the rear flexible hose from the rear flexible hose bracket.


c.
C365604

Remove the 2 bolts and separate the rear disc brake caliper assembly from the rear axle carrier sub-assembly.

NOTICE:

Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose.



Hide 42431 5.REMOVE REAR DISC

Hide 42312E 6.REMOVE REAR AXLE HUB BOLT

a.
C345044C02
0.677,1.354 0.677,1.135 0.677,1.135 1.125,1.135 true 1.531,1.906 1.531,1.417 1.531,1.417 1.406,1.417 true 1.719,0.802 1.719,0.615 1.719,0.615 1.833,0.615 true 0.615,1.354 0.885,1.542 0.271,0.188 10 true *a 1.448,1.927 1.719,2.115 0.271,0.188 10 true *a 1.865,0.531 2.208,0.74 0.344,0.208 10 true SST
*a Service Nut


Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the rear axle hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

SST
09611-12010  

NOTICE:

Do not damage the threads of the rear axle hub bolts.



Hide 42312E 7.INSTALL REAR AXLE HUB BOLT

a.
C345045C02
2.885,1.323 2.885,0.896 true 2.531,0.438 2.188,0.438 true 1.927,0.344 2.177,0.542 0.25,0.198 10 true *a 2.813,1.344 3.125,1.5 0.313,0.156 10 false *b
*a Service Nut
*b Washer


Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.


b.

Install a washer and service nut to the rear axle hub bolt as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.

NOTICE:
·

Install the service nuts to prevent damage to the rear axle hub bolts.

·

Do not damage the threads of the rear axle hub bolts.




d.

Remove the 3 service nuts and washer from the 3 rear axle hub bolts.


Hide 42431 8.INSTALL REAR DISC

Hide 9.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

a.

Install the rear disc brake caliper assembly to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)


b.

Install the rear flexible hose to the rear flexible hose bracket with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


c.

Connect the No. 2 parking brake wire assembly connector.


Hide 10.INSTALL REAR WHEEL

Hide 11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION


c.

Turn the power switch on (READY).


d.

Depress the brake pedal and release it.