Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
48760B
1.INSTALL REAR SUSPENSION SUPPORT ASSEMBLY
Secure the rear suspension support assembly in a vise using aluminum plates.
Do not overtighten the vise.
Install the rear suspension support assembly to the rear shock absorber assembly.
Apply a few drops of adhesive to the threads of a new rear support to rear shock absorber nut.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
| *a | Torque Wrench Fulcrum Length |
| *b | Turn |
| *c | Hold |
Using SST and a 6 mm hexagon socket wrench, hold the rear shock absorber rod and tighten a new rear support to rear shock absorber nut.
Securely insert the 6 mm hexagon socket wrench into the rear shock absorber rod to prevent damage to the rear shock absorber assembly when tightening the rear support to rear shock absorber nut.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using SST (fulcrum length of 40 mm (1.57 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):
20 N*m (204 kgf*cm, 15 ft.*lbf)
48554A
2.INSTALL REAR SHOCK ABSORBER CAP
Install the rear shock absorber cap to the rear shock absorber assembly.
48540
3.TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY
Temporarily install the rear shock absorber assembly to the rear axle carrier sub-assembly with the nut.
Hold the rear axle carrier pin while rotating the nut.
4.STABILIZE SUSPENSION
| *a | Wooden Block |
| *b | Jack |
|
Wooden Block Placement Location |
Using a jack and a wooden block, apply load to the suspension so that the rear No. 2 suspension arm assembly is positioned as shown in the illustration.
34.5 mm (1.36 in.)
Do not raise the jack up too high.
The vehicle could fall, resulting in a serious accident.
When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.
Make sure to perform this operation with the vehicle kept as low as possible.
48790
5.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY
Temporarily install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt and nut.
Insert the bolt with the threaded end facing the rear of the vehicle.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
48540
6.CONNECT REAR SHOCK ABSORBER ASSEMBLY
Connect the rear shock absorber assembly to the vehicle with the 2 bolts.
Temporarily tighten bolt A and then fully tighten the 2 bolts in the order of B and A.
48540
7.INSTALL REAR SHOCK ABSORBER ASSEMBLY
| *1 | Rear Axle Carrier Pin |
| *a | Torque Wrench Fulcrum Length |
| *b | Ball Joint Lock Nut Wrench |
| *c | Turn |
| *d | Hold |
Using a ball joint lock nut wrench fully tighten the rear shock absorber assembly with the nut.
Hold the rear axle carrier pin while rotating the nut.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a ball joint lock nut wrench (fulcrum length of 150.25 mm (5.92 in.)) + torque wrench (fulcrum length of 400 mm (1.31 ft.)):
91 N*m (928 kgf*cm, 67 ft.*lbf)
48790
8.INSTALL REAR UPPER CONTROL ARM ASSEMBLY
Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
48840A
9.INSTALL REAR STABILIZER LINK ASSEMBLY
89408C
10.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)
57628C
11.INSTALL REAR FLOOR SIDE MEMBER COVER LH
57627A
12.INSTALL REAR FLOOR SIDE MEMBER COVER RH
13.INSTALL REAR WHEEL
14.INSPECT AND ADJUST REAR WHEEL ALIGNMENT
15.PERFORM INITIALIZATION (w/ Height Control Sensor)