Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061609 HEATING / AIR CONDITIONING _0300711 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1473  A/C Inverter Start-up Signal System Malfunction  


DESCRIPTION

The inverter activation signal is sent to the compressor with motor assembly from the hybrid vehicle control ECU. Compressor control is stopped and this DTC is stored if there is an open or short in the signal circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1473 A/C Inverter Start-up Signal System Malfunction
Any of the following conditions is met:
·

Open in A/C inverter start-up signal circuit

·

Short in A/C inverter start-up signal circuit


·

Harness or connector between hybrid vehicle control ECU and compressor with motor assembly

·

Compressor with motor assembly

·

Hybrid vehicle control ECU

·

Hybrid control system

·

CAN communication system


-

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (READY) ○ ○
Malfunction Status Open in A/C inverter start-up signal circuit ○ -
Short in A/C inverter start-up signal circuit - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

E334616E06
0.958,1.813 1.417,2.01 0.458,0.198 10 false LIN 1.396,4.146 1.854,4.344 0.458,0.198 10 false 2 0.073,0.958 2.521,1.188 2.448,0.229 10 false Air Conditioning Amplifier Assembly 0.802,3.219 1.26,3.417 0.458,0.198 10 false DOUT 0.958,3.771 1.417,3.969 0.458,0.198 10 false IG1 0.885,4.344 1.344,4.542 0.458,0.198 10 false GND 0.969,5.125 1.427,5.323 0.458,0.198 10 false PB 0.979,5.635 1.438,5.833 0.458,0.198 10 false PE 1.344,5.646 1.781,5.823 0.438,0.177 10 false U1 1.344,5.125 1.781,5.302 0.438,0.177 10 false U1 1.302,4.344 1.74,4.521 0.438,0.177 10 false C13 1.302,3.771 1.74,3.948 0.438,0.177 10 false C13 1.302,3.219 1.74,3.396 0.438,0.177 10 false C13 1.25,1.667 1.708,1.865 0.458,0.198 10 false 2 1.385,3.583 1.844,3.781 0.458,0.198 10 false 1 1.385,3.021 1.844,3.219 0.458,0.198 10 false 3 1.385,4.938 1.844,5.135 0.458,0.198 10 false 2 1.385,5.458 1.854,5.656 0.469,0.198 10 false 1 0.146,2.313 0.604,2.51 0.458,0.198 10 false C20 0.146,2.469 2.594,2.698 2.448,0.229 10 false Battery State Sensor Assembly 2.198,3.917 3.271,4.198 1.073,0.281 10 false ECU-IG1 NO. 3 2.417,6.177 4.094,6.417 1.677,0.24 10 false HV Air Conditioning Wire 0.281,6.417 1.333,6.896 1.052,0.479 10 false Compressor with Motor Assembly 2.219,7.01 4.698,7.344 2.479,0.333 10 false : CAN Communication Line 2.219,7.417 4.156,7.698 1.938,0.281 10 false : LIN Communication Line 5.375,6.927 6.74,7.583 1.365,0.656 10 false Inverter with Converter Assembly 5.375,6.771 5.813,6.948 0.438,0.177 10 false U2 5.438,3.813 7.156,4.302 1.719,0.49 10 false Hybrid Vehicle Control ECU 5.438,3.656 5.875,3.833 0.438,0.177 10 false A49 5.083,5 5.542,5.198 0.458,0.198 10 false 1 5.083,5.521 5.542,5.719 0.458,0.198 10 false 2 5.281,5 5.719,5.177 0.438,0.177 10 false ACPB 5.281,5.521 5.719,5.698 0.438,0.177 10 false ACPE 6.031,3.219 6.469,3.396 0.438,0.177 10 false LIN3 5.781,3.063 6.24,3.26 0.458,0.198 10 false 17 3.76,3.792 5.75,3.99 1.99,0.198 10 false from IG1-NO. 1 Relay

CAUTION / NOTICE / HINT

CAUTION:
·
A361801

When troubleshooting, use either a tool wrapped with vinyl insulation tape or an insulated tool. (It is extremely dangerous when a high-voltage charge passes through a non-insulated tool causing a short.)

·
A340358

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks.

·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C23
1.531,0.75 1.948,0.333 true 1.958,0.219 2.271,0.417 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs for both systems are output simultaneously.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.CHECK FOR DTC

B

2.CHECK FOR DTC
a.

Check if air conditioning system DTCs are output.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
Only DTC B1473 is output A
DTCs B1473 and B1498 are output simultaneously B



A

3.CHECK FOR DTC

B

3.CHECK FOR DTC
a.

Check if hybrid control system DTCs are output.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 397
OK:

Hybrid control system DTCs are not output.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS

NG

4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Compressor Target Speed Compressor with motor assembly Min.: 0, Max.: 7500 -
Body Electrical > Air Conditioner > Active Test
Tester Display
Compressor Target Speed
50004 121 18
OK:

Compressor with motor assembly operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY