The hybrid vehicle control ECU and compressor with motor assembly communicate via direct line. Compressor control is stopped and this DTC is stored if communication information is cut off or abnormal information is received.
This DTC is also detected if high-voltage electricity supplied from the inverter with converter assembly to the compressor control circuit is shut off.
This DTC will be stored as a history DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1498 | Communication Malfunction (A/C Inverter Local) | Any of the following conditions is met:
·
Error in communication line between the hybrid vehicle control ECU and compressor with motor assembly ·
Open in communication line between the hybrid vehicle control ECU and compressor with motor assembly ·
High-voltage power source shut off |
·
Harness or connector between compressor with motor assembly and body ground ·
Harness or connector between hybrid vehicle control ECU and compressor with motor assembly, battery state sensor assembly ·
Hybrid vehicle control ECU ·
Compressor with motor assembly ·
HV air conditioning wire (harness or connector between compressor with motor assembly and inverter with converter assembly) ·
CAN communication system ·
Hybrid control system |
Memorized |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | Power switch on (READY) | ○ | ○ | ○ |
| Malfunction Status | Error in communication line between the hybrid vehicle control ECU and compressor with motor assembly | ○ | - | - |
| Open in communication line between the hybrid vehicle control ECU and compressor with motor assembly | - | ○ | - | |
| High-voltage power source shut off | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
When troubleshooting, use either a tool wrapped with vinyl insulation tape or an insulated tool. (It is extremely dangerous when a high-voltage charge passes through a non-insulated tool causing a short.)
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks.
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
Inspect the fuses for circuits related to this system before performing the following procedure.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs for both systems are output simultaneously.
Depending on the timing of the power supply to the 12 V power supply circuit and high-voltage circuit when the power switch is turned on (READY), an abnormal information signal may be output, causing this DTC to be stored. If the output DTC is a code that was memorized in the past, check the fuses and wire harnesses. If there is no malfunction, clear the DTC.
Using the GTS, check if the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if hybrid control system DTCs are output.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC P058A01 and P162B87 are output | A |
| Both DTC P058A01 and P162B87 are not output | B |
A
B
Disconnect the C19 battery state sensor assembly connector.
Check if air conditioning system DTCs are output.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B1498 is output | A |
| DTC B1498 is not output | B |
A
B
Reconnect the C20 battery state sensor assembly connector.
Disconnect the C13 compressor with motor assembly connector.
Check if hybrid control system DTCs are output.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC P058A01 and P162B87 are output | A |
| Both DTC P058A01 and P162B87 are not output | B |
A
B
Disconnect the A49 hybrid vehicle control ECU connector.
Disconnect the C20 battery state sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-17 (LIN3) - C13-3 (DOUT) | Always | Below 1 Ω |
| A49-17 (LIN3) - C20-2 (LIN) | Always | Below 1 Ω |
| A49-17 (LIN3) or C13-3 (DOUT) - Body ground | Always | 10 kΩ or higher |
| A49-17 (LIN3) or C20-2 (LIN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Do not disconnect the connector on the high-voltage side.
Disconnect the C13 compressor with motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C13-2 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C13-1 (IG1) - C13-2 (GND) | Power switch on (IG) | 11 to 14 V |
| C13-1 (IG1) - C13-2 (GND) | Power switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A49 hybrid vehicle control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-17 (LIN3) - C13-3 (DOUT) | Always | Below 1 Ω |
| A49-17 (LIN3) or C13-3 (DOUT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
If work is performed without wearing insulating gloves, there is a danger of electric shock.
Disconnect the U1 and U2 HV air conditioning wire connectors.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U1-2 (PB) - U2-1 (ACPB) | Always | Below 1 Ω |
| U1-2 (PB) or U2-1 (ACPB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
If work is performed without wearing insulating gloves, there is a danger of electric shock.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U1-1 (PE) - U2-2 (ACPE) | Always | Below 1 Ω |
| U1-1 (PE) or U2-2 (ACPE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
If work is performed without wearing insulating gloves, there is a danger of electric shock.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U1-2 (PB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG