The headlight ECU sub-assembly RH controls the headlight cleaner motor and pump assembly.
The headlight cleaner control relay controls the headlight cleaner motor and pump assembly.
First check that the front washer operates normally.
Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.
Check the headlight type.
| Result | Proceed to |
|---|---|
| for LED Headlight | A |
| for Halogen Headlight | B |
A
B
Read the Data List according to the display on the GTS.
Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Front Window Washer Switch | Washer switch condition | ON/OFF | ON: Windshield wiper switch assembly (front washer switch) on
OFF: Windshield wiper switch assembly (front washer switch) off |
- |
| Tester Display |
|---|
| Front Window Washer Switch |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A10 headlight cleaner control relay connector.
Inspect the headlight cleaner control relay.
Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER CONTROL RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight Cleaner Control Relay) |
Disconnect the headlight cleaner control relay connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A10-3 (IG) - Body ground | Power switch on (IG) | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A10-4 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight Cleaner Control Relay) |
Disconnect the headlight cleaner control relay connector.
Using a service wire, connect A10-6 (PB) and body ground.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Check the headlight cleaner motor and pump assembly operate.
Headlight cleaner motor and pump assembly operate.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A10 headlight cleaner control relay connector.
Disconnect the A17 headlight ECU sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A10-2 (H) - A17-7 (HLC) | Always | Below 1 Ω |
| A10-2 (H) or A17-7 (HLC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A17 headlight ECU sub-assembly RH connector.
Disconnect the F36 windshield wiper switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A17-18 (FRWA) - F36-7 (WF) | Always | Below 1 Ω |
| A17-18 (FRWA) or F36-7 (WF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight Cleaner Motor and Pump Assembly) |
Disconnect the headlight cleaner motor and pump assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A55-1 - Body ground | Power switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A55 headlight cleaner motor and pump assembly connector.
Disconnect the A10 headlight cleaner control relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A55-2 - A10-6 (PB) | Always | Below 1 Ω |
| A55-2 or A10-6 (PB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight Cleaner Control Relay) |
Disconnect the headlight cleaner control relay connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A10-5 (FRWA) - Body ground | Power switch on (IG), front washer switch off | 11 to 14 V |
| Power switch on (IG), front washer switch on | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight Cleaner Control Relay) |
Disconnect the headlight cleaner control relay connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A10-3 (IG) - Body ground | Power switch on (IG) | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A10-4 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight Cleaner Control Relay) |
Disconnect the headlight cleaner control relay connector.
Using a service wire, connect A10-6 (PB) and body ground.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Check the headlight cleaner motor and pump assembly operate.
Headlight cleaner motor and pump assembly operate.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3F-31 - Body ground | Light control switch in head position | Below 1 V |
| Light control switch off | 4.2 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3F instrument panel junction block assembly connector.
Disconnect the A10 headlight cleaner control relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3F-31 - A10-1 (HDLO) | Always | Below 1 Ω |
| 3F-31 or A10-1 (HDLO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3F-31 - MB-15 (HRLY) | Always | Below 1 Ω |
| 3F-31 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the headlight cleaner control relay assembly with a new or a known good one.
Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER CONTROL RELAY>REMOVAL
| Result | Proceed to |
|---|---|
| The operation of the headlight cleaner returns to normal. | OK |
| The operation of the headlight cleaner does not return to normal. | NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight Cleaner Motor and Pump Assembly) |
Disconnect the headlight cleaner motor and pump assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A55-1 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A55 headlight cleaner motor and pump assembly connector.
Disconnect the A10 headlight cleaner control relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A55-2 - A10-6 (PB) | Always | Below 1 Ω |
| A55-2 or A10-6 (PB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG