When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane departure alert system, pre-crash safety system, forward recognition camera system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
56111
1.CLEAN WINDSHIELD GLASS
When reusing the windshield glass:
Using a scraper, remove any remaining adhesive dam and adhesive residue from the windshield glass.
Be careful not to damage the windshield glass.
Clean the outer circumference of the windshield glass with a non-residue solvent.
Do not touch the windshield glass surface after cleaning it.
Even if using a new windshield glass, clean it with a non-residue solvent.
56115A
2.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Install the 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.
Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
56116C
3.INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Using a brush or sponge, coat the installation area of 2 new No. 2 windshield glass stoppers with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
| *a | Back Side of Windshield Glass |
| *b | Ceramic Notch |
| *c | Windshield Glass Edge Side |
Install the 2 new No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 13.7 to 14.7 mm (0.539 to 0.579 in.) |
Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
75533G
4.INSTALL WINDSHIELD OUTSIDE MOULDING
Using a brush or sponge, coat the installation area of a new windshield outside moulding with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
| *a | Back Side of Windshield Glass |
| *b | Edge of Curved Surface |
Install the new windshield outside moulding to the windshield glass as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 6.5 mm (0.256 in.) |
| b | 2.5 to 7.5 mm (0.098 to 0.295 in.) |
56117A
5.INSTALL WINDOW GLASS ADHESIVE DAM
| *a | Cut |
Cut a new window glass adhesive dam so that it is the appropriate size as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 297.9 cm (9.77 ft.) |
Using a brush or sponge, coat the installation area of the new window glass adhesive dam with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
Install the window glass adhesive dam to the windshield glass as shown in the illustration.
| *a | Back Side of Windshield Glass | *b | Ceramic Notch |
| *c | Window Glass Adhesive Dam Positioning Center | - | - |
|
Primer G | - | - |
56153C
6.INSTALL FRONT WINDOW INNER CENTER MOULDING
Perform the following procedure only when replacement of a front window inner center moulding is necessary.
| *a | Back Side of Windshield Glass |
|
Primer G |
Using a brush or sponge, coat the installation area of a new front window inner center moulding with primer G.
| Area | Dimension |
|---|---|
| a | 14.5 mm (0.571 in.) |
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
| *a | Back Side of Windshield Glass |
| *b | Matchmark |
Install the new front window inner center moulding to the windshield glass as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 0.5 mm (0.020 in.) or less |
Do not damage the front window inner center moulding.
Remove the matchmarks.
56111
7.INSTALL WINDSHIELD GLASS
Clean and shape the contact surface of the vehicle body.
Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.
Leave as much adhesive on the vehicle body as possible.
Clean the contact surface of the vehicle body with a piece of cloth saturated with nonresidue solvent.
| *a | Matchmark |
Position the windshield glass.
Using suction cups, place the windshield glass in the correct position.
Check that the whole contact surface of the windshield glass rim is perfectly even.
Align the matchmarks on the windshield glass and vehicle body.
Check that the windshield glass stoppers are engaged to the vehicle body correctly.
Remove the windshield glass.
Using a brush, coat the installation surface on the vehicle body with primer M.
Do not coat the adhesive with primer M.
Do not apply too much primer M.
Allow the primer M to dry for 3 minutes or more.
Throw away any leftover primer M.
If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.
Using a brush or sponge, coat the adhesive application area with primer G.
| *a | Back Side of Windshield Glass | *b | Adhesive Application Area |
| *c | Ceramic Notch | - | - |
|
Primer G | - | - |
| Area | Dimension |
|---|---|
| a | 7.0 mm (0.276 in.) |
| b | 10.0 mm (0.394 in.) or more |
| c | 11.0 mm (0.433 in.) or more |
| d | 19.0 mm (0.748 in.) or more |
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
Apply primer G to the ceramic notches.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
Apply adhesive to the windshield glass.
Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent
| *a | Cartridge Nozzle |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 12.0 to 15.0 mm (0.472 to 0.591 in.) |
| b | 8.0 to 11.0 mm (0.315 to 0.433 in.) |
Load the sealer gun with the cartridge.
Apply adhesive to the windshield glass as shown in the illustration.
| *a | Back Side of Windshield Glass | *b | Adhesive Positioning Center |
| *c | Window Glass Adhesive Dam Positioning Center | *d | Ceramic Notch |
|
Adhesive | - | - |
| Area | Dimension |
|---|---|
| a | 9.5 mm (0.374 in.) |
| b | 3.0 mm (0.118 in.) |
| c | 6.6 mm (0.260 in.) |
| d | 8.0 mm (0.315 in.) |
Apply adhesive to the ceramic notches.
| *a | Matchmark |
Install the windshield glass.
Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.
Check that the windshield glass stoppers are engaged to the vehicle body correctly.
Check the clearance between the vehicle body and windshield glass.
Lightly press the outer surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body.
Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Hold the windshield glass using protective tape until the applied adhesive becomes hard.
Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.
When replacing the windshield glass or front window inner center moulding with a new one:
Remove the 2 protective retainers from the front window inner center moulding.
Do not damage the front window inner center moulding.
Make sure to remove the protective retainers.
w/ Windshield Deicer System:
Connect the connector of the windshield deicer.
8.INSPECT FOR LEAK
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
863C0
9.INSTALL DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY (w/ Digital Audio Broadcasting Antenna)
63311C
10.INSTALL ROOF HEADLINING
Return the front section of the roof headlining to its original position.
74348
11.INSTALL VISOR HOLDER
74320
12.INSTALL VISOR ASSEMBLY LH (w/ Vanity Light)
74310
13.INSTALL VISOR ASSEMBLY RH (w/ Vanity Light)
Use the same procedure as for the LH side.
74320
14.INSTALL VISOR ASSEMBLY LH (w/o Vanity Light)
74310
15.INSTALL VISOR ASSEMBLY RH (w/o Vanity Light)
Use the same procedure as for the LH side.
74325
16.INSTALL VISOR BRACKET COVER
74610A
17.INSTALL ASSIST GRIP SUB-ASSEMBLY
74612
18.INSTALL ASSIST GRIP COVER
62212
19.INSTALL FRONT PILLAR GARNISH ASSEMBLY LH
62211
20.INSTALL FRONT PILLAR GARNISH ASSEMBLY RH
Use the same procedure as for the LH side.
62312B
21.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
22.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
81340
23.INSTALL VANITY LIGHT ASSEMBLY
81260A
24.INSTALL MAP LIGHT ASSEMBLY
25.INSTALL FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)
89941
26.INSTALL RAIN SENSOR (w/ Rain Sensor)
87810
27.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)
87810
28.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)
55708
29.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
85221B
30.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
85211B
31.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
85292B
32.INSTALL FRONT WIPER ARM HEAD CAP
75534
33.INSTALL WINDSHIELD OUTSIDE MOULDING LH
75533
34.INSTALL WINDSHIELD OUTSIDE MOULDING RH
Use the same procedure as for the LH side.