The radio and display receiver assembly and stereo component amplifier assembly are connected by the AVC-LAN communication line.
This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly and stereo component amplifier assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15D3 | Stereo Component Amplifier Disconnected | When either condition below is met:
·
The stereo component amplifier assembly is/was not connected while the power switch is/was on (ACC or IG). ·
Communication between the master unit and the stereo component amplifier assembly is not possible when the hybrid control system is started. |
·
Stereo component amplifier assembly power source circuit ·
AVC-LAN circuit between radio and display receiver assembly and stereo component amplifier assembly ·
Stereo component amplifier assembly ·
Radio and display receiver assembly ·
Harness or connector |
The radio and display receiver assembly is the master unit.
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | The power switch is/was ON or ACC | ○ | - |
| The hybrid control system is started | - | ○ | |
| Malfunction Status | The stereo component amplifier assembly is/was not connected | ○ | - |
| Communication between the master unit and the stereo component amplifier assembly is not possible | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
Inspect the fuses for circuits related to this system before performing the following procedure.
If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.
| Result | Proceed to |
|---|---|
| DTC B15C3 is not output. | A |
| DTC B15C3 is output. | B |
A
B
Check that optional components (including associated wiring) which generate radio waves are not installed.
| Result | Proceed to |
|---|---|
| Optional components (including associated wiring) are installed. | A |
| Optional components (including associated wiring) are not installed. | B |
Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.
A
B
Remove optional components (including associated wiring).
Do not remove optional components or associated wiring without the permission of the customer.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the stereo component amplifier assembly connectors.
| *a | Front view of wire harness connector
(to Stereo Component Amplifier Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F75-3 (GND) - Body ground | Always | Below 1 Ω |
| F75-18 (GND2) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F75-1 (+B) - F75-3 (GND) | Power switch off | 11 to 14 V |
| F75-16 (+B2) - F75-3 (GND) | Power switch off | 11 to 14 V |
| F76-12 (ACC) - F75-3 (GND) | Power switch on (ACC) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F125 radio and display receiver assembly connector.
Disconnect the F76 stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F125-7 (TX1+) - F76-8 (TX+) | Always | Below 1 Ω |
| F125-8 (TX1-) - F76-7 (TX-) | Always | Below 1 Ω |
| F125-7 (TX1+) - Body ground | Always | 10 kΩ or higher |
| F125-8 (TX1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the stereo component amplifier assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL