Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › SIMPLE INTELLIGENT PARKING ASSIST SYSTEM › 2016.10–2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0303239 SIMPLE INTELLIGENT PARKING ASSIST SYSTEM C

PARK ASSIST / MONITORING  SIMPLE INTELLIGENT PARKING ASSIST SYSTEM  C1612  IG Voltage is High  


DESCRIPTION

This DTC is stored when the clearance warning ECU assembly judges, as a result of its self check, that the voltage received by terminal IG is not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1612 IG Voltage is High IG voltage is high
·

Wire harness or connector

·

Clearance warning ECU assembly



WIRING DIAGRAM

E361568E01
0.979,0.677 4.042,0.875 3.063,0.198 10 false from IG1-NO. 1 Relay 2.885,0.885 4.875,1.083 1.99,0.198 10 false ECU-IG1 NO. 4 5.469,0.698 5.781,0.896 0.313,0.198 10 false IG 5.208,0.573 5.365,0.771 0.156,0.198 10 false 8 5.208,1.01 5.365,1.208 0.156,0.198 10 false 1 5.479,1.135 5.635,1.333 0.156,0.198 10 false E 5.385,1.677 5.844,1.875 0.458,0.198 10 false F38 5.396,1.833 6.594,2.427 1.198,0.594 10 false Clearance Warning ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization may be needed. Refer to Calibration.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs
50002 170

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the F38 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY IG POWER SUPPLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY IG POWER SUPPLY)
a.

Disconnect the clearance warning ECU assembly connector.


b.
E361567C01
0.323,0.958 0.74,1.26 0.417,0.302 2.281,1 2.698,0.583 true 1.51,1.75 1.24,1.063 true 2.76,0.49 3.073,0.688 0.313,0.198 10 false IG 1.49,1.802 1.646,2 0.156,0.198 10 false E 0.406,1.021 0.865,1.219 0.458,0.198 10 false F38 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F38-8 (IG) - F38-1 (E) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR