Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2016.10–2020.08
RM32K0E _55 Steering _061343 STEERING COLUMN _0303431 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Steering Lock does not Lock  


DESCRIPTION

The steering lock actuator or upper bracket assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little, as is done for a vehicle with a mechanical key, to change the position of the lock hole.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Steering Lock does not Lock
Entry&Start
·

Lock Request Receive

·

S Code Check

·

L Code Check

·

Steering Lock


Main Body
·

FL Door Courtesy SW (for LHD)

·

FR Door Courtesy SW (for RHD)


Power Source Control
·

Shift P Signal


-

WIRING DIAGRAM

C315118E17
0.094,1.406 1.688,2.125 1.594,0.719 10 false ID Code Box (Immobiliser Code ECU) 4.479,4.802 7.156,5.365 2.677,0.563 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 0.094,1.24 0.51,1.542 0.417,0.302 10 false F21 0.896,0.635 1.313,0.938 0.417,0.302 10 false LIN1 1.25,0.479 1.667,0.781 0.417,0.302 10 false 2 0.24,3.729 1.417,4.427 1.177,0.698 10 false Main Body ECU (Multiplex Network Body ECU) 1.698,3.74 3.229,4.365 1.531,0.625 10 false Certification ECU (Smart Key ECU Assembly) 1.698,3.573 2.052,3.906 0.354,0.333 10 false F1 2.625,2.531 3.042,2.833 0.417,0.302 10 false LIN 2.917,2.344 3.333,2.646 0.417,0.302 10 false 13 2.927,3.271 3.344,3.573 0.417,0.302 10 false 25 2.49,3.375 2.906,3.677 0.417,0.302 10 false SLR+ 5.375,2.51 5.792,2.813 0.417,0.302 10 false LIN 5.188,2.354 5.604,2.656 0.417,0.302 10 false 5 5.365,2.948 5.781,3.25 0.417,0.302 10 false B 5.188,2.813 5.573,3.219 0.385,0.406 10 false 7 5.365,4.167 5.781,4.469 0.417,0.302 10 false GND 5.365,3.396 5.781,3.698 0.417,0.302 10 false IGE 5.188,3.271 5.573,3.677 0.385,0.406 10 false 3 5.177,4.021 5.563,4.427 0.385,0.406 10 false 1 4.271,3.104 5.146,3.438 0.875,0.333 10 false STRG LOCK 4.49,4.615 5.51,4.833 1.021,0.219 10 false F78 2.958,2.844 3.823,3.219 0.865,0.375 10 false from Auxiliary Battery 0.771,5.375 4.438,5.573 3.667,0.198 10 false : CAN Communication Line 0.771,5.083 3.052,5.323 2.281,0.24 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Perform either of the following operations to lock/unlock the steering:

-

To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG).

-

To lock the steering, turn the power switch off with the shift lever in P, and then open a door.


·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the steering lock ECU (steering lock actuator or upper bracket assembly), certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), registration must be performed (refer to Service Bulletin).

·

After performing repairs, confirm that the problem does not recur.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.READ VALUE USING GTS (LOCK REQUEST RECEIVE)
a.

Use the Data List to check if the steering lock command is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lock Request Receive Reception state of steering lock request signal by certification ECU (smart key ECU assembly) sent to ID code box (immobiliser code ECU)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".



OK or NG OK: Lock request received within 10 seconds of opening any door with power switch off and shift lever in P
NG: Except above
If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Lock Request Receive
50003 125 68
OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the power switch from on (IG) to on (ACC) or off and opening a door with the shift lever in P, and OK is displayed on the GTS screen.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (S CODE CHECK)

NG

10.READ VALUE USING GTS (DOOR COURTESY SW)
2.READ VALUE USING GTS (S CODE CHECK)
a.

Use the Data List to check if S code certification is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 125 65
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (L CODE CHECK)

NG

9.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
3.READ VALUE USING GTS (L CODE CHECK)
a.

Use the Data List to check if L code certification is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator or upper bracket assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

8.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Disconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C350526C09
1.5,0.833 2,1.083 0.5,0.25 0.917,1.813 1.25,2.427 true 2.521,1.802 2.188,2.417 true 0.323,0.208 0.635,0.365 0.313,0.156 10 false *a 1.635,0.833 2.01,1.104 0.375,0.271 10 false F78 0.552,1.719 0.917,1.917 0.365,0.198 10 false GND 2.573,1.667 2.833,1.875 0.26,0.208 10 false B
*a Front view of wire harness connector
(to Steering Lock ECU Steering Lock Actuator or Upper Bracket Assembly))


Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F78-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.


Standard Voltage:
Tester Connection Condition Specified Condition
F78-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Reconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C241547C80
0.083,0.917 0.583,1.167 0.5,0.25 0.354,2.896 1.729,3.063 1.375,0.167 2.313,2.958 2.719,3.073 0.406,0.115 1.563,4.031 2.521,4.198 0.958,0.167 2.302,1.104 2.823,1.917 true 1.573,2.896 2.896,2.625 2.896,2.625 2.635,2.958 true 2.115,4.198 2.115,4.458 true 1.854,1.104 1.083,1.917 true 0.24,0.146 0.563,0.375 0.323,0.229 10 false *a 2.927,2.521 3.104,2.708 0.177,0.188 10 false *b 2.042,4.469 2.344,4.667 0.302,0.198 10 false *c 0.219,0.927 0.531,1.094 0.313,0.167 10 false F78 0.938,1.948 1.458,2.208 0.521,0.26 10 false IGE 2.708,1.958 3.063,2.125 0.354,0.167 10 false GND 3.052,4.01 3.427,4.177 0.375,0.167 10 false GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
*b Steering Lock Motor not Operating
*c Steering Lock Motor Operating


Check the signal waveform according to the condition(s) in the table below.

Standard Frequency:
Item Content
Tester Connection F78-3 (IGE) - F78-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Operating → Not operating


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG).

-

To lock the steering, turn the power switch off with the shift lever in P, and then open a door.





Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


c.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


d.

Check for deformation and corrosion of the connector case and terminals.

OK:

There is no deformation or corrosion of the connector case or terminals.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F78-3 (IGE) - F1-25 (SLR+) Always Below 1 Ω
F78-3 (IGE) or F1-25 (SLR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Reconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


c.
C350527C18
1.5,0.583 2,0.833 0.5,0.25 2.583,2.75 1.865,1.979 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 2.542,2.802 2.948,2.969 0.406,0.167 10 false IGE 1.625,0.594 1.938,0.75 0.313,0.156 10 false F78
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G26-3 (IGE) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

8.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Perform registration (refer to Service Bulletin).


c.

Use the Data List to check if L code certification is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

9.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


b.

Perform registration (refer to Service Bulletin).


c.

Use the Data List to check if S code certification is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 125 65
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

10.READ VALUE USING GTS (DOOR COURTESY SW)
a.

Using the GTS, check the following main body ECU (multiplex network body ECU) Data List item by opening and closing the driver door to confirm the state of the front door courtesy light switch assembly.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly RH (for RHD) ON or OFF ON: Front door RH open
OFF: Front door RH closed
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part.
FL Door Courtesy SW Front door courtesy light switch assembly LH (for LHD) ON or OFF ON: Front door LH open
OFF: Front door LH closed
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part.
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 197,199
OK:

The Data List item changes in accordance with the opening and closing of the driver door.



Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (SHIFT P SIGNAL)

NG

GO TO LIGHTING SYSTEM (DOOR COURTESY SWITCH CIRCUIT)

11.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Move the shift lever to P.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position (P) signal ON or OFF ON: Shift lever in P
OFF: Shift lever not in P
·

Use this item to determine if the shift position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal
50003 223 1
OK:

ON is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (STEERING LOCK)

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (PROBLEM SYMPTOMS TABLE)

12.READ VALUE USING GTS (STEERING LOCK)
a.

Check that the steering is unlocked.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Lock State of whether steering lock ECU (steering lock actuator or upper bracket assembly) determined steering is locked Set or Unset Set: Steering locked
Unset: Steering unlocked
If this item displays "Unset", the steering is not locked.
Body Electrical > Entry&Start > Data List
Tester Display
Steering Lock
50003 125 47
OK:

Set is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (LOCK REQUEST RECEIVE)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

13.READ VALUE USING GTS (LOCK REQUEST RECEIVE)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


b.

Perform registration (refer to Service Bulletin).


c.

Turn the power switch on (IG).


d.

Use the Data List to check if the steering lock command is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lock Request Receive Reception state of steering lock request signal by certification ECU (smart key ECU assembly) sent to ID code box (immobiliser code ECU)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".



OK or NG OK: Lock request received within 10 seconds of opening any door with power switch off and shift lever in P
NG: Except above
If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Lock Request Receive
50003 125 68
OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the power switch from on (IG) to on (ACC) or off and opening a door with the shift lever in P, and OK is displayed on the GTS screen.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)