Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061839 PRE-COLLISION _0303861 PRE-COLLISION SYSTEM Y

PRE-COLLISION  PRE-COLLISION SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use these procedures to troubleshoot the pre-collision system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
2.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
Pre-collision System Customer Problem Analysis Vehicle Brought to Workshop
Year Month Day
Dealer name Person in charge at headquarters Telephone number
Shop name Person in charge at shop
Frame type Frame No. First Registered Year Total distance traveled
Customer Concerns (Include details) Does not operate
Operates abnormally
Date of malfunction occurrence (Since when) Year Month Day Approx. Time
Date of last inspection Year Month Day
Frequency of problem symptoms Once / Occasionally (times per day, times per month) / Every time certain conditions are met ( )
Weather Sunny / Cloudy / Rain / Snow (Amount of snowfall cm) / Other ( ) Vehicle speed Approximately ( ) km/h
Place Prefecture
(Attach a map if possible)
Driving path (where vehicle turned, where driver attempted to drive to, etc.)
* Describe the conditions immediately after the occurrence in as much detail as possible.
Conditions of Occurrence Diagram
E322002

E322001E01
0.771,1.104 0.313,0.458 0.313,0.458 0.719,0.458 true 1.365,1.042 1.646,0.76 1.646,0.76 1.99,0.76 true 0.406,1.854 0.198,1.854 0.198,1.854 1.063,1.177 true 1.875,1.271 2.083,1.438 true 1.563,1.469 1.719,1.885 1.719,1.885 1.927,1.885 true 0.75,0.063 1.99,0.26 1.24,0.198 10 false Diagram Example 0.781,0.385 3.229,0.583 2.448,0.198 10 false Oncoming vehicle 2.042,0.677 3.208,1 1.167,0.323 10 false Stopped vehicle 0.479,1.792 1.406,2.01 0.927,0.219 10 false Occurred here 1.979,1.823 3.052,2.021 1.073,0.198 10 false Vehicle 2.135,1.354 3.427,1.604 1.292,0.25 10 false Approximately ( ) m

Surrounding road conditions
Describe whether there were any billboards, metal objects on the road (manholes), guardrails, pipes, cat's eyes, gate bars, etc.
Urban area / Suburbs / Highway / Other ( ) Road surface conditions Temperature About °C ( °F)
Direction of travel Straight / Right turn / Left turn / Right curve / Left curve Snow wall(s) Y / N
Driving lane Number of lanes on one side (lanes) / ( ) lane(s) from left Backlighting Y / N
Condition of external area around detection sensor No foreign matter / Foreign matter (water, snow, ice, other)
Additional information about condition of vehicle exterior (other than above)
DTC First Time (when vehicle brought to workshop)
Second Time (after clearing DTC)
Status of operation switch Pre-collision system cancel switch Far / Medium / Near / OFF VSC OFF switch ON / OFF
Serial number of main part
* Fill in when removing, installing or replacing part
Forward recognition camera
Describe the items to the right in as much detail as possible. Driver operation Accelerator pedal operated / Brake pedal operated / Steering wheel operated Time elapsed after engine was started Approximately ( ) minutes
Tire pressure inspection result Front: LH ( ) kPa RH ( ) kPa Standard ( ) kPa
Rear: LH ( ) kPa RH ( ) kPa Standard ( ) kPa
Sensor optical axis inspection result Forward recognition camera Accident history Y / N
Millimeter wave radar sensor assembly Accident history Y / N
Vehicle modified Y ( ) / N
Items installed or attached around windshield glass Drive recorder* / Radar detector / Navigation unit (genuine/non-genuine) / ETC / Charms or toys / Other:
*: As information regarding the item is important for the investigation, make sure to obtain the item if permission is given by the customer.

Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the power switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*
4.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*


c.

Connect the GTS to the DLC3.


d.

Turn the power switch to on (IG).


e.

Turn the GTS on.


f.

Turn the cruise control main switch on.


g.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Misalignment Reading.


h.

Check the amount of misalignment and make a note.

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Misalignment Reading
50005 220 4405

i.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Offset Reading.


j.

Check the amount of offset and make a note.

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Offset Reading
50005 220 4406

Result:
Proceed to
NEXT



NEXT

5.CHECK CAN COMMUNICATION SYSTEM*
5.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check if the CAN communication system is functioning normally.

HINT:

Refer to CAN Bus Check in CAN Communication System.

for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


OK:

CAN communication system is functioning normally.



Result:
Proceed to
OK
NG



OK

6.INSPECT WARNING LIGHT

NG

6.INSPECT WARNING LIGHT
a.

Check the condition of the warning lights on the combination meter assembly.


Result:
Result Proceed to
Only the PCS warning light is blinking A
The PCS warning light is not blinking
The PCS warning light and other warning lights are illuminated or blinking B



A

7.INSPECT MULTI-INFORMATION DISPLAY

B

GO TO MALFUNCTIONING SYSTEM

7.INSPECT MULTI-INFORMATION DISPLAY
a.

Check if a pre-collision system warning message is displayed on the multi-information display in the combination meter assembly.


Result:
Result Proceed to
"Pre-Collision System Malfunction Visit Your Dealer" is displayed A
Any of the following messages is displayed:
·

"Pre-Collision System Unavailable"

·

"Pre-Collision System Unavailable Clean Sensor"

·

"Front Camera Unavailable"

·

"Front Camera Vision Blocked. Clean and Demist Windshield"


B
Warning message is not displayed C



A

8.CHECK FOR DTCs (PRE-COLLISION SYSTEM)

B

C

CHECK CONDITIONS WHEN PRE-COLLISION SYSTEM DID NOT OPERATE

8.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
HINT:

Refer to DTC Check / Clear.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR


a.

Check for DTCs and note any codes that are output.

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

b.

Clear the DTCs.

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

c.

Recheck for DTCs.

i.

Attempt to duplicate the malfunction and check if the DTCs are output again.

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220


Result:
Result Proceed to
Malfunction is duplicated but DTCs are not output A
Malfunction cannot be duplicated and DTCs are not output B
DTCs are output C



A

9.PROBLEM SYMPTOMS TABLE

B

C

9.PROBLEM SYMPTOMS TABLE
HINT:

Refer to Problem Symptoms Table.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

10.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

12.CONFIRMATION TEST
10.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

11.ADJUST, REPAIR OR REPLACE
11.ADJUST, REPAIR OR REPLACE
NOTICE:

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

12.CONFIRMATION TEST
12.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END