Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2016.10–2020.08
RM32K0E _58 Vehicle Interior _061839 PRE-COLLISION _0303861 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  C1A11  Front Radar Sensor Incorrect Axial Gap  C1A14  Front Radar Sensor Beam Axis Not Adjusted  


DESCRIPTION

When the system determines that the vehicle is driving straight ahead based on signals from the yaw rate and acceleration sensor (airbag sensor assembly), etc., the millimeter wave radar sensor assembly performs self-diagnosis to check if the sensor beam axis is misaligned.

C1A11 is output when it is determined that the millimeter wave radar sensor assembly beam axis is misaligned.

If sensor beam axis adjustment is not performed after installing a new millimeter wave radar sensor assembly, C1A14 is output.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A11 Front Radar Sensor Incorrect Axial Gap After the power switch is turned to on (IG), misalignment of the millimeter wave radar sensor assembly continues for 0.1 seconds or more Millimeter wave radar sensor assembly
C1A14 Front Radar Sensor Beam Axis Not Adjusted At a vehicle speed of 10 km/h (7 mph) or higher, axis misalignment of the millimeter wave radar sensor assembly was not adjusted for 0.1 seconds or more Millimeter wave radar sensor assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



PROCEDURE

1.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Check if the stored DTCs are current DTCs.


b.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
Current DTC C1A11 is output A
Current DTC C1A14 is output B
History DTC C1A11 is output C



A

2.CHECK VEHICLE CONDITION

B

12.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

C

14.CLEAR DTC (PRE-COLLISION SYSTEM)
2.CHECK VEHICLE CONDITION
a.

Check the operating conditions of the vehicle.

HINT:

DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is temporarily misaligned due to the vehicle being overloaded.



Result:
Result Proceed to
Vehicle is not overloaded or has not been towed. A
Vehicle is overloaded or has been towed. B



A

3.CHECK WHEEL ALIGNMENT

B

10.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
3.CHECK WHEEL ALIGNMENT
a.

Check the front and rear wheel alignment (toe).

Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT

HINT:

DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is misaligned due to incorrect wheel alignment (toe).



Result:
Result Proceed to
Front or rear wheel is misaligned (toe) A
Front and rear wheels are not misaligned (toe) B



A

4.ADJUST WHEEL ALIGNMENT

B

7.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY
4.ADJUST WHEEL ALIGNMENT
a.

Adjust the alignment (toe) of the wheels.

Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
6.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
HINT:

After performing the radar sensor beam axis adjustment, if the same DTC is output again after the DTC detection conditions are met, replace the millimeter wave radar sensor assembly.


a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A11 is not output A
DTC C1A11 is output B



A

END

B

8.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
7.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Check that the bracket of the millimeter wave radar sensor assembly is not deformed.

HINT:

When the bracket is deformed, replace the millimeter wave radar sensor assembly.


OK:

The bracket is not deformed.



Result:
Proceed to
OK
NG



OK

5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

8.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
8.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC (PRE-COLLISION SYSTEM)
9.CLEAR DTC (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

Result:
Proceed to
NEXT



NEXT

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

10.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Return the vehicle to normal operating conditions.


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT (PRE-COLLISION SYSTEM)
11.CHECK DTC OUTPUT (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A11 is not output A
DTC C1A11 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS MISALIGNED DUE TO THE VEHICLE BEING OVERLOADED OR TOWED)

B

3.CHECK WHEEL ALIGNMENT
12.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

13.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
13.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
HINT:

After performing the radar sensor beam axis adjustment, if the same DTC is output again after the DTC detection conditions are met, replace the millimeter wave radar sensor assembly.


a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A14 is not output A
DTC C1A14 is output B



A

END (SENSOR BEAM AXIS ADJUSTMENT WAS NOT COMPLETED)

B

8.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
14.CLEAR DTC (PRE-COLLISION SYSTEM)
a.

Check for DTCs related to misalignment of millimeter wave radar sensor assembly.

HINT:

If only history DTCs are stored, they may have been stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when beam axis learning was performed.



b.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

Result:
Proceed to
NEXT



NEXT

END