Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061839 PRE-COLLISION _0303861 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  C1A4B  Stop Light Relay Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) sends a stop light operation request signal to the stop light switch assembly. If the skid control ECU (brake actuator assembly) detects a malfunction in the stop light switch assembly circuit, the millimeter wave radar sensor assembly stores DTC C1A4B.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4B Stop Light Relay Circuit Diagnosis condition:
·

Power switch to on (IG) and battery voltage between 11 and 14 V


Malfunction condition:
Either of the following conditions is met:
·

When the stop light illumination output (STPO) signal is on, a signal has not been input to the STP terminal for 0.3 seconds or more continuously.

·

When the stop light illumination output (STPO) signal is off, signals input to the STP terminal and STP2 terminal of the skid control ECU (brake actuator assembly) differ for 0.3 seconds or more continuously.


·

Electronically controlled brake system

·

Millimeter wave radar sensor assembly



DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch to on (IG) and battery voltage between 11 and 14 V. ○ ○
Malfunction Status When the stop light illumination output (STPO) signal is on, a signal has not been input to the STP terminal. ○ -
When the stop light illumination output (STPO) signal is off, signals input to the STP terminal and STP2 terminal of the skid control ECU (brake actuator assembly). - ○
Detection Time 0.3 seconds 0.3 seconds
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

The pre-collision system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
HINT:

Pre-collision system DTC C1A4B may be stored due to a malfunction in the VSC system. Therefore, it is necessary to check for and troubleshoot VSC system DTCs first.


a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B



A

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)

B

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A4B is output A
DTC C1A4B is not output B



A

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



B