The millimeter wave radar sensor assembly is connected to the skid control ECU (brake actuator assembly) by a CAN communication line.
When entering test mode, the skid control ECU (brake actuator assembly) communicates with the millimeter wave radar sensor assembly and determines whether the vehicle is equipped with a pre-collision system.
U023A is output when it is determined that the vehicle is not equipped with a pre-collision system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U0235 | Lost Communication with Cruise Control Front Distance Range Sensor | When entering test mode, the skid control ECU (brake actuator assembly) determines that the vehicle is not equipped with a pre-collision system | ·
Skid control ECU (Brake actuator assembly) ·
Millimeter wave radar sensor assembly ·
Wire harness or connector |
When replacing the millimeter wave radar sensor assembly, always replace it with a new one.
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
The pre-collision system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC U0235 and other DTCs are output | A |
| Only DTC U0235 is output | B |
A
B
Check for DTCs.
| Result | Proceed to |
|---|---|
| Electronically controlled brake system DTC are not output | A |
| Electronically controlled brake system DTC are output | B |
A
B
When entering test mode, the skid control ECU (brake actuator assembly) communicates with the millimeter wave radar sensor assembly to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit test mode within 5 seconds of entering test mode.
Procedure to Enter Test Mode (Signal Check)
Turn the power switch to on (IG).
for Manual Transmission:
Check that the shift lever is in neutral and apply the parking brake.
for Automatic Transmission:
Check that the shift lever is in P and apply the parking brake.
Put the steering wheel in the neutral position.
Connect the GTS to the DLC3.
Turn the power switch to on (IG).
Turn the GTS on.
Switch the skid control ECU (brake actuator assembly) to Test Mode (Signal Check) using the GTS. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.
Do not exit test mode within 5 seconds of entering test mode. If test mode is exited within 5 seconds of entering test mode, DTC U0235 may be stored. If DTC U0235 is output after exiting test mode, enter test mode again, wait at least 5 seconds, then recheck for DTCs.
| Tester Display |
|---|
| Signal Check |
Test Mode (Signal Check) Display Check
Check that the ABS warning and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.
If the ABS warning and slip indicator lights remains illuminated or does not illuminate when Test Mode (Signal Check) is entered, a component or wire harness may be malfunctioning.
End of Test Mode (Signal Check)
Turn the power switch to off and disconnect the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC U0235 is not output | A |
| DTC U0235 is output | B |
A
B
Replace the millimeter wave radar sensor assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL
Adjust the millimeter wave radar sensor assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC U0235 is not output | A |
| DTC U0235 is output | B |
A
B
Replace the skid control ECU (brake actuator assembly).
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT