Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0303875 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 62180A 1.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY

NOTICE:

When installing a curtain shield airbag assembly, have assistants hold it to prevent it from bending.


a.

Check that the power switch off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Engage the hooks and claws (A) to temporarily install the curtain shield airbag assembly.

B459842C01
1.365,0.823 1.5,0.604 true 2.51,0.896 2.646,1.219 true 3.271,0.688 3.406,0.469 true 4.729,0.823 4.875,0.635 true 6.563,2.115 6.792,1.771 true 3.656,2.24 3.906,2.24 true 1.583,1.844 1.833,1.844 true 1.688,2.25 1.906,2.479 true 1.229,2.417 1.083,2.552 1.083,2.552 1.542,2.427 true 1.531,0.469 1.76,0.667 0.229,0.198 10 true *b 2.667,1.24 2.896,1.438 0.229,0.198 10 true *c 3.427,0.323 3.656,0.521 0.229,0.198 10 true *b 4.917,0.51 5.146,0.708 0.229,0.198 10 true *b 6.385,2.104 6.615,2.302 0.229,0.198 10 false *d 3.948,2.135 4.177,2.333 0.229,0.198 10 false *a 1.875,2.51 2.104,2.708 0.229,0.198 10 false *2 0.917,2.5 1.146,2.698 0.229,0.198 10 false *c 1.865,1.698 2.094,1.896 0.229,0.198 10 false *1
*1 Clip *2 Curtain Shield Airbag Clip Spacer
*a Pin *b Claw (A)
*c Claw (B) *d Spacer Location



d.

Install the 3 new bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

NOTICE:

Do not twist the curtain shield airbag assembly when installing it.



e.

Install the curtain shield airbag assembly with new spacer and new clip.

HINT:

Engage the claws (B) to install each new clip.



f.

Using needle nose pliers, push the pins into the clips.

NOTICE:
·

Do not damage the pins.

·

Make sure that the pins of the clips are pushed in firmly.




g.
B459841C01
2.583,0.667 2.167,0.333 true 1.698,1.885 1.365,1.552 true 1.167,1.448 1.333,1.615 0.167,0.167 10 true *a 1.979,0.229 2.292,0.385 0.313,0.156 10 false *b
*a Airbag Connector
*b Airbag Connector Lock


Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



h.

Push in the airbag connector lock to install the airbag connector.

NOTICE:

Securely lock the airbag connector lock.



Hide 2.INSTALL ROOF HEADLINING ASSEMBLY

Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION