Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT AIRBAG SENSOR › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0303878 FRONT AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT AIRBAG SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front airbag sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 28800 2.REMOVE AUXLIATY BATTERY

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>REMOVAL

NOTICE:

When remove the auxiliary battery, some systems need to be initialized after the auxiliary battery is installed.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 89174A 3.REMOVE FRONT AIRBAG SENSOR

a.

Check that the power switch off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B453192

Remove the bolt and disengage the claw to separate the front airbag sensor.

NOTICE:

Loosen the bolt while holding the front airbag sensor because the front airbag sensor pin (claw) is easily damaged.



d.

Disconnect the connector to remove the front airbag sensor.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

B312073C28
4.354,1 4.896,0.979 true 3.813,1.75 3.813,1.365 false 0.74,2.448 0.271,1.875 true 4.156,0.708 4.531,0.646 true 4.938,0.875 5.25,1.031 0.313,0.156 10 false *a 3.74,1.792 4.052,1.948 0.313,0.156 10 false *b 0.125,1.719 0.438,1.875 0.313,0.156 10 false *c 4.583,0.521 4.896,0.75 0.313,0.229 10 false (A)
*a White Housing Lock *b Yellow CPA
*c Connector lock is released - -



ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




e.

After disconnecting the connector, check that the position of the white housing lock is as shown in the illustration.

B296255C01
4.76,1.833 5.042,2.073 0.281,0.24 10 false *b 1.396,1.833 1.729,2.125 0.333,0.292 10 false *b 4.76,0.573 5.052,0.885 0.292,0.313 10 false *a 1.396,0.573 1.656,0.844 0.26,0.271 10 false *a
*a Incorrect *b Correct