Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM32K0E _58 Vehicle Interior _062271 SEAT BELT _0304120 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The combination meter assembly blinks or turns off the seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner belt assembly (driver seat).

WIRING DIAGRAM

A394825E01
0.052,1.5 1.25,1.875 1.198,0.375 10 false Combination Meter Assembly 1.531,1.5 3.177,1.885 1.646,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 2.458,0.833 2.906,1.031 0.448,0.198 10 false DBKL 2.979,0.844 3.427,1.042 0.448,0.198 10 false MB 3,0.625 3.219,0.802 0.219,0.177 10 false 18 3.948,0.635 4.198,0.792 0.25,0.156 10 false 33 3.938,0.844 4.219,1.031 0.281,0.188 10 false 3H 3.323,1.281 4.406,1.844 1.083,0.563 10 false Instrument Panel Junction Block Assembly 5.031,0.75 5.198,0.906 0.167,0.156 10 false 3 5.833,0.75 6,0.906 0.167,0.156 10 false 2 4.583,1.156 5.552,1.344 0.969,0.188 10 false M61*1, M73*2 4.573,1.333 6.51,1.708 1.938,0.375 10 false Front Seat Inner Belt Assembly (Driver Seat) 0.49,2.375 2.365,2.583 1.875,0.208 10 false : CAN Communication Line 4.281,2.094 6.156,2.302 1.875,0.208 10 false *1: for RHD 4.302,2.396 6.177,2.604 1.875,0.208 10 false *2: for LHD 5.208,0.75 5.365,0.948 0.156,0.198 10 false + 5.646,0.75 5.802,0.948 0.156,0.198 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



HINT:
·

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.Check that the operation of the seat belt warning light is normal first.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION

·

If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Seat Buckle SW Driver seat belt buckle switch ON or OFF ON: Driver seat belt unfastened
OFF: Driver seat belt fastened
-
Body Electrical > Main Body > Data List
Tester Display
D Seat Buckle SW
50003 123 14

OK:

ON or OFF appears on the GTS screen according to the driver seat belt condition.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT)
2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT)
a.

Remove the front seat inner belt assembly (driver seat).

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the front seat inner belt assembly (driver seat) (seat belt warning switch).

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT)

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL

B426689C14
2.083,1 2.417,1.25 0.333,0.25 5.5,0.75 5.833,1 0.333,0.25 2.417,2.146 2.417,1.563 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.156,1.052 2.469,1.25 0.313,0.198 10 false MB 5.583,0.802 5.896,1 0.313,0.198 10 false 3H 2.25,2.198 2.865,2.396 0.615,0.198 10 false DBKL
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 3H instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-18 (DBKL) - 3H-33 Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT) - BODY GROUND)

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
3H-33 - M73-3 (+) Always Below 1 Ω
M73-3 (+) - Body ground Always 10 kΩ or higher
M73-2 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
3H-33 - M61-3 (+) Always Below 1 Ω
M61-3 (+) - Body ground Always 10 kΩ or higher
M61-2 (E) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR