Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM32K0E _58 Vehicle Interior _062271 SEAT BELT _0304120 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

When the power switch is on (IG), the combination meter assembly monitors the state of the front passenger side seat and the front seat inner belt assembly (front passenger seat) and also whether the front passenger seat is occupied. If the front passenger side seat belt is not fastened, the seat belt warning light of the combination meter assembly blinks. If the seat belt is fastened, the warning light goes off.

WIRING DIAGRAM

A394820E02
0.427,1.333 0.885,1.531 0.458,0.198 10 false CPU 1.198,1.333 1.656,1.531 0.458,0.198 10 false I/F 1.771,1.094 2.229,1.292 0.458,0.198 10 false PKBI 2.219,1.063 2.385,1.26 0.167,0.198 10 false 7 2.583,0.99 2.917,1.188 0.333,0.198 10 false 3*1 2.99,0.979 3.323,1.177 0.333,0.198 10 false 3*2 2.99,1.51 3.323,1.708 0.333,0.198 10 false 2*2 2.604,1.51 2.938,1.708 0.333,0.198 10 false 2*1 0.26,2.708 0.594,2.906 0.333,0.198 10 false F4 0.25,2.865 2.25,3.115 2,0.25 10 false Combination Meter Assembly 2.563,1.177 2.896,1.375 0.333,0.198 10 false M53 2.969,1.177 3.302,1.375 0.333,0.198 10 false M51 2.958,1.729 3.292,1.927 0.333,0.198 10 false M51 2.563,1.729 2.896,1.927 0.333,0.198 10 false M53 3.375,1.094 3.708,1.292 0.333,0.198 10 false + 3.385,1.625 3.719,1.823 0.333,0.198 10 false E 2.906,2.177 4.854,2.635 1.948,0.458 10 false Front Seat Inner Belt Assembly (Front Passenger Seat) 4.625,0.969 4.958,1.167 0.333,0.198 10 false 1 4.615,1.188 4.948,1.385 0.333,0.198 10 false O 4.615,1.729 4.948,1.927 0.333,0.198 10 false O 4.625,1.5 4.958,1.698 0.333,0.198 10 false 2 5.021,2.167 6.615,2.719 1.594,0.552 10 false Separate Type Front Seat Cushion Pad (Occupant Detection Sensor) 2.635,3.021 3.635,3.271 1,0.25 10 false *1: for LHD 2.646,3.365 3.646,3.615 1,0.25 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


HINT:
·

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.Check that the operation of the seat belt warning light is normal first.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION

·

If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL



PROCEDURE

1.READ VALUE USING GTS (P-SEATBELT BUCKLE SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch is on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger seat belt buckle switch signal ON or OFF ON: Front passenger seat belt not fastened
OFF: Front passenger seat belt fastened
Perform the inspection while sitting in the front passenger side seat.
Body Electrical > Combination Meter > Data List
Tester Display
P-Seatbelt Buckle SW
50003 122 7

Result:
Result Proceed to
ON or OFF is displayed on the GTS screen according to the front passenger side seat belt condition and front passenger seat condition (occupied or unoccupied) A
ON or OFF is not displayed normally on the GTS screen according to the front passenger side seat belt condition B



A

REPLACE COMBINATION METER ASSEMBLY

B

2.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (FRONT PASSENGER SEAT) - COMBINATION METER ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (FRONT PASSENGER SEAT) - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the F4 combination meter assembly connector.


b.

Disconnect the M53*1 or M51*2 front seat inner belt assembly (front passenger seat) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F4-7 (PKBI) - M53-3 (+) Always Below 1 Ω
F4-7 (PKBI) or M53-3 (+) - Body ground Always 10 kΩ or higher
M53-2 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
F4-7 (PKBI) - M51-3 (+) Always Below 1 Ω
F4-7 (PKBI) or M51-3 (+) - Body ground Always 10 kΩ or higher
M51-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FRONT PASSENGER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FRONT PASSENGER SEAT)
a.

Remove the front seat inner belt assembly (front passenger seat).

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the front seat inner belt assembly (front passenger seat).

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY (FRONT PASSENGER SEAT)

4.INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)
a.

Remove the separate type front seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL


b.

Inspect the separate type front seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)